Jump to content

ATA ABS Helmet Build Thread


Recommended Posts

Hello,

 

This is my first build and i am starting with a ATA Helmet. I received the brow box some month ago, but i must admit i was a little bit stressed and take a lot of time to watch build threads to be sure i can apply : "Think twice, cut once !"

I'll try to follow the advices of this build thread : http://www.whitearmor.net/forum/topic/14806-how-to-assembling-ata-abs-helmet-1/

 

OK, so let's start !

IMG_0476.jpg

IMG_0477.jpg

The kit looks really beautiful ! 

 

I start by marking the trim area around the ears with a whiteboard erasable pen. I then used a plastic piece to mark the top of the cap

IMG_0478.jpg

IMG_0479.jpg

IMG_0480.jpg

 

I then drilled a hole in the junction area

IMG_0482.jpg

Same on the other side

IMG_0483.jpg

 

I then start to cut with a metal knife. The ABS is really thick ! It's hard to cut.

IMG_0484.jpg

 

IMG_0485.jpg

 

Then i do the same on the face plate

IMG_0486.jpg

IMG_0487.jpg

 

And the section under the neck

IMG_0489.jpg

 

According to the post i'm using as a reference, i draw line at 1.25" above the eyes (around 3.2 cm)

IMG_0490.jpg

and then i cut it

IMG_0491.jpg

 

I am then sanding all the cuttings to have something smooth and clean

IMG_0493.jpg

 

 

Time to cut the eyes. I mark the bump around the eyes with the whiteboard marker

IMG_0492.jpg

 

Using a Dremel i'll cut the eyes

IMG_0494.jpg

 

IMG_0495.jpg

IMG_0496.jpg

 

Then, using sandpaper and small file i smooth all the cuttings

IMG_0497.jpg

 

Using the dremel, i then sands the back of the teeth to open them

IMG_0498.jpg

 

Then, using a hobby blade and some small files, i opened all the teeth

IMG_0499.jpg

 

IMG_0500.jpg

 

what do you thing of my frown ? Should i "square" it a little bit more ?

Edited by sebastien
  • Like 1
Link to comment
Share on other sites

  • 3 weeks later...

Ok, next run.

I tried to fit both parts of the helmet together and attach with clamps :

IMG_0543.jpg

I checked on both sides how it fits

IMG_0544.jpg

IMG_0545.jpg

 

Then, i drilled the ear hole to attach both parts together :

IMG_0546.jpg

And add the screw :

IMG_0547.jpg

Same on the other side :

IMG_0548.jpg

 

On the left side (looking at the helmet), it seem to fit well :

IMG_0549.jpg

 

On the right side, i have a small plastic part that is not going the good way. It's seems the problem is the same for all ATA :

IMG_0552.jpg

 

I do not already have my heat gun, so i used an iron to get that piece back on the good side :

IMG_0553.jpg

 

It's starting to really look gooooood !

IMG_0554.jpg

 

Ok, now it's time to go for the hardest part : the ears....

Hopefully, ATA Helmet kit comes with 2 pairs, so you can make mistakes.

 

Let's take a beer-stop, move to the garage where i can make more dust and start with that ears.

OK, first step, i tried to use a whiteboard pen to draw the "flat" part of the ear :

IMG_0559.jpg

 

Then i draw the curved part, following approximatively the indentation i can guess and another line far below to show where i need to cut. I start cutting straight the flat part using my magic dremel extension :

IMG_0560.jpg

 

the cut is rough, it really looks horrible on the pictures. But the idea is just to remove some material and then to sand until i have the perfect fit.

 

IMG_0561.jpg

 

Ok, some material is removed, it's now time to move to the sanding tool :

IMG_0562.jpg

 

Looks really much better  :)

IMG_0563.jpg

 

OK, there's really too much material and i need to sand more

IMG_0565.jpg

 

Still sanding until it fits on both sides. I do not have pictures, but on the flat side, i also sand the front portion for 2mm to match the fit between the rear side and the front side of the helmet :

IMG_0566.jpg

 

IMG_0567.jpg

 

Then i drilled the holes :

IMG_0568.jpg

The lower hole too and screwed everything together :

IMG_0569.jpg

 

I then sand the lower portion of the ears, near the bucket opening to have something smooth

IMG_0570.jpg

 

OK, next ear, on this one, the limit seems much more clear (should have started with this one  :laugh1: ) :

IMG_0571.jpg

Rough cut :

IMG_0572.jpg

And final fit :

IMG_0573.jpg

IMG_0574.jpg

 

Now i removed the screws and washed the bucket to remove mold oil (it smells like my engine oil  :lol: ) :

IMG_0575.jpg

 

OK, that's it for this run. Next step : painting. I'm still wondering if i would like to plasti-dip the inner bucket and before that, i need to determine if i will attach the lens on the screws (more simple) or cut eyes in the lens material and attach it on some small wood pieces attached around the eyes (nicer but really more complex).

To be continued :smiley-sw013:  

Edited by sebastien
Link to comment
Share on other sites

OK, next run.

I tried to find a moskito mesh to stick inside the teeth

IMG_0590.jpg

I cut it the shape of the mouth

IMG_0593.jpg

 

OK, now it's time to paint ! I really do not feel comfortable with painting so i asked for some help of my wife  ;) 

I purchased Humbrol paint.

 

I started with the easiest, the mic tips

IMG_0597.jpg

I painted them using black mate spray paint

IMG_0598.jpg

To be sure i would not make any mistake, i purchased a "DaveM" decals set :

IMG_0607.jpg

started with the back shapes :

IMG_0608.jpg

then front shapes :

IMG_0609.jpg

 

I taped the outside of the mouth to be sure there will be no paint outside the mouth

IMG_0592.jpg

 

OK, my wife decided to start with the vocoder :

IMG_0605.jpg

It's looking gooood darling !

IMG_0610.jpg

IMG_0611.jpg

then the mouth (OK, the blue tape is really useless...) :

IMG_0613.jpg

 

Removed the tape, its looking really good after the second coat and the mic tips :

IMG_0631.jpg

 

The ears, starting with a black coat :

IMG_0612.jpg

then the gray one :

IMG_0627.jpg

 

 

I cut the lens material to get a straight band :

IMG_0600.jpg

 

I then drilled a hole on one side :

IMG_0601.jpg

and attached the lens to the first screw :

IMG_0602.jpg

I then drilled the second hole and attached the lens to the second screw :

IMG_0603.jpg

using a whiteboard marker i draw the nose shape and the cut the nose :

IMG_0604.jpg

 

I then mount the helmet all together with the lens, say "hello" Mr "No stripes" :

IMG_0636.jpg

 

time to stick the stipes :

IMG_0642.jpg

 

yes !

IMG_0644.jpg

 

It's awesome, i love it !

IMG_0646.jpg

 

OK, next i tried to stick the s-shaped liner under the bucket, but i experienced some problems :

IMG_0641.jpg

IMG_0640.jpg

It seems i have some "bumps" as the s-shaped liner is bend too much. I tried it in different ways and the photo above seem to be the best i was able to achieve...

Do you have an idea about the way i can avoid this ?

Link to comment
Share on other sites

the "bumps" are usually pretty unavoidable due to the bucket shape. What you can do is put super glue inside the bump and clamp it tight. This will diminish the bump completely.

 

as for as the build goes, looks good. I would however try to open up the painting on the frown a bit to try to get as close as possible to the "teeth" upper and lower marks.

Link to comment
Share on other sites

the "bumps" are usually pretty unavoidable due to the bucket shape. What you can do is put super glue inside the bump and clamp it tight. This will diminish the bump completely.

 

as for as the build goes, looks good. I would however try to open up the painting on the frown a bit to try to get as close as possible to the "teeth" upper and lower marks.

OK, thanks for the super glue tip, i will do that.

For the teeth too, you are right, when i look at pictures in centurion applications it seems the paint is closer to border.

Link to comment
Share on other sites

oh and sorry to keep adding to your list, but please fix the ears. Make sure the black line is much thinner. Basically you want the lines uniform in your build to look like the sticker outlines you have. 

Just use the gray and open up little by little.

Link to comment
Share on other sites

  • 8 months later...

OK, i took me around 1 year to finally take pictures and update my build thread  :laugh1:

I reduced the size of the black lines to match the stickers

IMG_2317.jpg

 

And add more paint on the frown

IMG_2316.jpg

 

try to add just a touch more gray on the frown to get it as close to the external "mouth" lines as possible for the top. the bottom looks flush..

Edited by illusionz_09
Link to comment
Share on other sites

Duh on my part. I've even posted on it. 

 

No problem, thank you for your encouragements on both of my threads  :duim:

 

try to add just a touch more gray on the frown to get it as close to the external "mouth" lines as possible for the top. the bottom looks flush..

 

Ok, thank you for this feedback, i will do it.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...