PGHtrooper21

The good thing is that for a box of 100 the price $5.00 includes shipping to the lower 48 States! I want to see if these are correct before I order them. Andy

Stephen, To the left of the ab belt and below the drop boxes, what is the strip with the three round buttons for? Is that for the covers for the snaps on the ab belt? Andy

Stephen, Thanks. Thanks for the info. Are you using E6000 to glue everything? I am using E6000 on my AP build. Are you using a blade for "score and cut"? or sicssors? Keep us updated with the build! Cheers! Andy

While searcing for Brass "8mm or 5/16" split Rivits, I came across this site. ----------- While scrolling down I came across "Flower Shaped Brass Split Rivits" Do any of these work? Andy

Stephan, Hi, AWESOME KIT from the pics!!!!!! Are there any "trim lines" on the kit? Did you do any "Trimming" on it? Is the pvc harder to trim than abs or easer? Next year I might buy one! Andy

I wear corrective lenses. The problem I see is if your prescription changes you will need to invest in another set of lenses. Also, how would it effect if the lense is bubble for "Hero" and "Flat" for "Stunt" It is like taking your glasses and slanting them. When you do it, things start to become blurred. Also, sometimes when the lense is made it is not right and have to be made again? Also, when installing the lense into the helmet how is it going to be installed? Glue, tape or some type of holding device? If the lense gets damaged, is it insured or will the person have to pay a fee to replace it? Swimming and diving glasses are designed to be more secure and fitted to the individual. While our helmets depending on what is used inside are not designed and secured as well. Just my thoughts. Andy

Thanks again to all who were helpng me with my pics problem! Now I am ok! All the time I spent the last few months working on this Helmet, taking pictures uploading them to photobucket and writing my journal and pasting them here, and run into the problem that I had was frustrating. Seeing them all posted makes me feel alot better! Thanks to all on FISD!!!! TROOPERS HELPING OTHER TROOPERS!!!!! Andy

After I painted the lines, I looked at some screen worn helmets on Starwarshelmets.com to get an idea of putting on “Rank Bars Strips†on the “Ear Bumpsâ€. I decided to put it on the third “Bumpâ€.

After letting the ears dry, I begin the outlining of the “Ear Bumpsâ€. I used a “No. Liner Brush†for this. I dipped the brush into the Gloss Black Paint and wiped off the excessive paint and went to it. I made sure to secure my Helmet in my lap and started with the sides going very carefully along the edge of the “Grey Paint†and the “Pencil Lineâ€. I did this for both sides.

I picked up†Prym Creative Liquid Seam Sealant†from ‘Wal Mart. I did this to prevent the ends of the “Elastic†from fraying. I read the instructions and it said to get a pin and poke a hole at the tip of the bottle and put the sealant on the edge of the fabric and let sit for 15 minutes. I put the sealant on both sides of the end of the “Elastic†and the tip as well. Make sure you put the “elastic†to dry on a piece of paper or cardboard with the edges up so it could dry. When putting on the sealant, doing it helps to be outside or in a well-ventilated area so to keep the fumes at bay.

Now on to finish up the other strap; I basically did the same thing as for the first strap. The difference is to put the other tool parts on the snapping tool. I then folded over the end part of the “elastic†and then marked the edge with the Yellow Pencil. Then I measured, spaced and marked the snap with the Yellow Pencil. I also used another snap as a guide for centering the mark. I did not put a piece of elastic on this side as on the other strap. I measured and it did not need one. I used the “Revolving Punch Tool†and squeezed and punch a hole into the “elastic. I then I placed the snaps in the “Elastic†and placed the “Snap Tool†on the snaps and hold it in place, and took it down to my cellar and got my hammer and tapped a few times to secure the snap. The trick of this and the previous part is to hold the “Snap Tool†securely while not trying to hit your fingers! I found out when tapping the snaps you can tell when the snap is secure by the sound the tool makes and the feel of the hammer on the “Snap Toolâ€.

Next up, is putting on the snaps. For this I would like to thank Karin “Queen of The Hand guards on FISD for the size of the straps. I tried to measure with the helmet on and I was not confident with my measurements. So I would like to say a ‘THANK YOU†to Karin again. When doing this step, I put the snaps on the cutting mat to line them up with each other. I again read the back of the snaps to see which snap goes with each other. Them I opened up the Snap Tool I read the back a few times to understand what needs to be done. I then put each of the tools in the proper part of the tool for use. Then I started to work on the longer side with the two snaps. I folded the one side over to where I could fit, center and space two snaps. I used a tape measure to space the distance between them and to center them. The reason why I did this is to make sure that the snaps connect snug. I then used the Yellow Pencil to mark where I want to punch the holes. I put an extra piece of “Black Elastic†between the fold. I made sure to mark the end of the fold with the Yellow Pencil and to line up the pieces evenly and secure it with a “Black Paper Clipâ€. I adjusted the “Revolving Hole Punch†for the right setting and squeezed and punched out two holes. Then I placed the snaps where they need to be placed I then I placed the snaps in the “Elastic†and placed the “Snap Tool†on the snaps and hold it in place, and took it down to my cellar and got my hammer and tapped a few times to secure the snap. Also, on the same side I put on an extra “eyelet†for support.

I used “Eyelets†in the “Black Elastic†so the elastic will not tear over time when pulling on the straps.