Jump to content

Harder

501st Stormtrooper[TK]
 View Profile  See their activity

  • Posts

    208

  • Joined

  • Last visited

 Content Type 

Posts posted by Harder

  2. Let's do it Harder...

    in ESB Build Threads

    Posted

    ok, so now I have some questions:

     

    Everything seems to fit well, except the thigh pieces.  I am considering three options.  1. do nothing its normal, and please tell me if I am over doing it, 2. I raise up the thigh plates by shortening the elastic holders of the thigh plates to the underbelt, or 3. I need to cut and resize the thigh plates.

     

    p5jDiT7.jpg 

    There is a distinctive gap in the top of the thighs.  The knees are normal-ish, but my girlfriend can put a full hand inside at the top as it was fit on the first time.

     

    iNlojFi.jpg

     

    three fingers if she does sideways.

    7qEhU8s.jpg

     

    Second to the thighs, the shins are super hard to hook up and tend to pop apart.  I can slip my foot through them without unhooking them.  This also seems too loose.  Please advise on this.

    you can see from my left shin plate, its popped back open but again I can slip it on closed.

    p5jDiT7.jpg

     

     

     

    Next, I noticed the bicep plates are not linked or tied to the shoulders in any way, and they kept sliding down to my elbow. Which makes me stand a little funny, unless im doing some sort of action.  I am thinking I need to connect the biceps to the shoulders to keep them in place.  For ESB, is this something I can do, or what is the preferred suggestions to make this fit a little better?

    EHh5XPH.jpg

     

     

    Another "fit" concern is the belt and drop boxes.  The snaps are nearly centered on the lower abdomen plate, however, and maybe its just poor quality, but the drop boxes are right there, and cut.. leaving well, less than desired appearance.  The craftsmanship is not what I would've expected.

    1lNQIvh.jpg2lVpb5H.jpg 

     

     

     

    Lastly, I noticed the green film inside the helmet is rather flimsy and cheap and again, poorly crafted.

    Is this normal?

    uyades1.jpg

     

     

     

    All these little detail points, I will admit, once fully on, it doesn't look half bad.

     

    tWA24Be.jpg

     

    Kcgk3zJ.jpg

     

    BE90uNC.jpg

     

    I think this picture is the worst ever.  You can easily se how the thighs are too big, and even at the calf.

    • Like 1

  3. Let's do it Harder...

    in ESB Build Threads

    Posted

    Hello all.  Yesterday the BBB came.  Pics are here, and I have of course suited up to see how things fit.  I do have some questions.

     

    I will start with the unboxing.

    xbvPL58.jpg

    Fedex came promptly 2 hrs and 15 mins later than predicted.  You can imagine my anxiousness for that time, wondering where the truck was being robbed.

     

    BEpjeSO.jpg

    A few posed pictures and I immediately went into opening it.

     

    TalWMty.jpg nQHCZRT.jpg w0OZRpI.jpg k8BMReV.jpg DqDlWRR.jpg eq2N2j3.jpg

     

    And the money shot is here..

    k4uhpxM.jpg 

    What a manchild. lol!!

     

     

     

     

     

    • Like 5

  15. Polishing armor that won't damage ABS???

    in Tutorials, Tips and HOWTOs

    Posted

     WHAT!  not sure were you got that from NEVER use acetone base products on plastic will ruin finish,  just simple car polish.
     
    Mark (AP)

    It is safe to vapor polish plastic. I am a ME in polymer science and plastics.

    I will agree with this statement, I wouldn’t use it directly on the plastic or paint. I did state only if it’s solid color thru. This thread was about polishing plastic, but I see it’s really asking about polishing paint. Or the subject is now, rather. In that circumstance, yes. Vapor polishing will not give the best result.

    Nonetheless, doing proper research into various methods of polishing and knowing the piece being worked on is always my recommendation.


    Sent from my iPhone using Tapatalk

  19. Should I buy a Kit ?

    in ANH (Stunt and Hero)

    Posted

    Good morning!

    Completely agree with the previous comments before me. The question your asking is really your question.

    To their point. Some people prefer to have that experience. And some are looking for the fast route.

    I will tell you my choice. I chose to buy, yes at a high cost, a fully commissioned set of armor. I did a lot of research, and I’ve also purchased the posible mannequin, electronics, etc. I have a degree in ME, PSY, BA, and Statistics. I am more than capable to build my own. But for me.. my decision came down to Volunteering and Trooping.

    I highly desire to help people. I have personal experience with children with needs and I saw the affect in their spirits and strength when the troopers come and volunteer. It fills my heart immeasurably.

    That was my deciding factor. But much like different ingredients in chicken soup, even the 501st needs variety of people.

    You should decide what gives you the most benefit, personally.

    Either way, you’ll not be disappointed.

    Good luck future trooper!


    Sent from my iPhone using Tapatalk

    • Like 1

  23. Anyone have suggestions for a CLEAN mesh install?

    in Assembly, Mods, and Painting

    Posted

     

    16 hours ago, MaskedVengeance said:


    If you’re in the contiguous US and PM me your mailing address I’ll send you some.


    Sent via Imperial Tapatalk Comms

     

    Sent!

     

    13 hours ago, gmrhodes13 said:

    I'd be really interested to see over time if there was any bleed through, some paint and thinners can react with ABS and colors can bleed.

     

    I don't use the same paint/covering I normally just use enamel satin spray paint, doesn't reflect light having a dull finish and also doesn't affect the ABS, I made sure I tested that before using it.

     

    Just for interests sake I saw this on a recent EIB request, looks like a material not a paint/coating but still very cool, I'm not sure how it will go with sweat though, can get pretty wet in there, I know I've removed my armor after a hot troop to find a waterfall of sweat inside the backplate and chest

     

    Xd8IbeZ.jpg&key=10af8bd106a0b90b4d43d5cb

     

     

     

    I like this!!  I want to offer some of my professional experience.  I am a degreed BS in ME specific to Polymer Science of Plastics.  Yes, most all plastics can experience some level of chemical reaction to paint.  There's "a way" to do it.  Example is all the plastic parts in the automotive industry.  I won't go into all the chemical formulas about how certain types of alcohol or specifically ethanol can render down the polymer chains of ABS from polymers to monomers.  Anyway, a thin coat of either clear or binder to the plastic before applying any color, will prevent any breakdown or bleeding.

     

    Krylon brand paint has a couple extra carbon elements in the paint which help it grip and bind really good to plastic, especially ABS since it has a Carbon, Nitrogen, Hydrogen backbone.  You "can" use an acrylic paint if you like, however, I strongly suggest using an oil de-binder first, like Dawn dish soap, rinse, and let dry for at least 30-45 mins.. followed by light sanding to give it a rougher surface.

    • Like 1
×
×
  • Create New...