Fash Posted January 25, 2017 Report Share Posted January 25, 2017 Here i go Name = Ashley Bryce Forum Name = Fash Legion ID = 30094 Garrison = UK Armor Maker = DA Props Helmet Maker = DA Props Blaster Type = Shear Tec rubber blaster E11 Boots Maker = Loake chelsea boot hand painted Canvas belt = ISD Hand Plates Type = ISD Silicone Electronics = Rom FX Neck Seal Type = ISD Faux leather Holster Maker = ISD Quote Link to comment Share on other sites More sharing options...
Fash Posted January 25, 2017 Author Report Share Posted January 25, 2017 sorry forgot a photo so here it is also the title is wrong can admit change please so it reads as it should EIB it my sausage fingers sorry Quote Link to comment Share on other sites More sharing options...
ukswrath[Staff] Posted January 31, 2017 Report Share Posted January 31, 2017 Thanks Ashley, Andrew or myself will be with your shortly Quote Link to comment Share on other sites More sharing options...
Fash Posted January 31, 2017 Author Report Share Posted January 31, 2017 Thanks look forward to hearing from you guys Quote Link to comment Share on other sites More sharing options...
ukswrath[Staff] Posted February 4, 2017 Report Share Posted February 4, 2017 Hello Ashley welcome to your EI review and thank you for your application. Lets take a look. CRL and EIB Application Requirements: All submission photos have been posted. Your armor displays all the necessary elements to qualify for Expert Infantry. Welcome trooper, congratulations! Other-Armor Fit/Assembly: In this section we review observations made by your fellow troopers and ourselves. Some observations may lead to suggestions to improve the overall look of your armor. If any suggestion affects any application, it will be listed separately in the above or below sections. We have a few areas to go over but nothing incredibly major. 1) Starting from the top and working our way down you've done wonderful job painting your helmet. The rear trap stripes should amount to around 13, you seems to have 17 which makes the traps themselves look crowded or busy. We're recommending you repaint this area to match what you see in the reference helmet photo we've provided. Reference photo 2) Though very minor the right side shoulder bell gap is larger the left. a minor adjustment here should do the trick. 3) The back plate to kidney gap should be little to no gap. With your arms down it appears to be within spec but when you lift your arms up the gap grows which leads us to suspect you're using elastic to connect the two. We're suggesting you use nylon webbing or similar to help prevent this from happening. Reference photos 4) It appears a good majority of the cover strips on your limps are too long, they should stop at or before the edge of the armor. To make the armor look more uniform and for your own safety we're suggesting you trim them back a bit. Reference photo 5) The vertical Ab button has too much return edge and should be trimmed down a bit, As seen in the reference photo I've provided it should be Reference photo 6) Minor return edge on the wrist side of your forearms. Not a big deal but the there should be no return edge in this area. Reference photo 7) The cover strip on the rear of the shin should stop just below the upper return edge. This will need to be trimmed back. Reference photo Centurion Suggestions: In this section we prepare you for Centurion. If there were any areas of concern they would be discussed here. We do have a couple areas that will need to be address before applying for Centurion if you choose to do so. 1) There can be little to no gap between the ab and kidney ans stated in the CRL. This will need to be corrected. The most common solution is to either tighten the connecting straps. If you're using elastic, nylon webbing would be the alternative and suggested. For level three certification (if applicable): Ideally there no gap between the abdomen and kidney armor. Reference photo 2) Your's is not bad but the drop box is to be aligned with the outer edge of the waist ammo belt. Reference photo. That's it! Excellent job on your build. Hope to see you at Centurion. Quote Link to comment Share on other sites More sharing options...
Fash Posted February 4, 2017 Author Report Share Posted February 4, 2017 Thank you so much for the advice will start work on the adjustments and see you at the next level Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.