hiro2501

I am currently working on the chest plate and upper arm parts. In my case, I don't need the optional Level 3 certification at this point. However, since the chest is in a prominent position in the whole armor, I plan to make holes and line it with black fabric this time to ensure that the finish meets the highest possible standard. Also, the initial hot cut edges of each part are obviously rough and not smooth, so I plan to fix them as I go. This is the current state of the front and back of the chest. Should I shave off the 6 small holes until they form a smoother curve?

I had a dream of receiving the 501st's approval before SWCJ2025, but it didn't come true. However, even if it's a slow pace, I'm happy that I feel like the completion of my armor is getting better by completing the work steadily.

JB weld adhesives and putties are also sold in my country. I expect that there will be many modifications to the armor build, not just this upper arm part, but in various other places. To do this, I feel that more information on adhesives and putties is needed. Thank you for your valuable information. I also appreciate you informing me of the activity schedule of each detachment, including the 501st, regarding SWCJ2025.

Thank you. It's encouraging to me.

I used epoxy putty to fill in the gaps in the joints, then used polyester putty to create an even smoother surface. This was my first experience using putty, and I ended up ordering the wrong type of putty when I ordered it. What arrived at my house was lacquer putty, not polyester putty. I looked up the instruction manual and watched YouTube, and there didn't seem to be much difference in how they were used, so I used them as they were. In other words, this image is of the lacquer putty. I'm very worried about the finished product because I have nothing to compare it to. But I'm going to keep using the file to smooth out the surface. This is an image using epoxy putty. This is Cemedine.CO epoxy putty for plastics. For the lacquer putty, I used Tamiya putty basic type. Starwars Celebration Japan 2025 will be held from April 18th. Are there any of you seniors who will participate? I will participate in the event. It was my dream to participate with armor approved by the 501st Japan Chapter, but unfortunately I will not be able to make it in time. However, I am very excited to be able to exchange SW culture with many people. I have also prepared my first SWAG. Would it be possible to post a link to my SWAG X here?

When I access imgur using Chrome on my regular PC, an ad appears at the top and a three-second countdown appears on the right, after which the entire screen goes black. At first I suspected that it was due to my PC settings, and searched various websites, but the cause remained a mystery. I realized that I could turn off the intrusive ads by using an incognito window, so I started using imgur little by little. Is my use of Direct link correct? I used some leftover armor scraps with E6000 adhesive to trim the corners of the upper arms at an angle, which is a characteristic of TLJ.

Thank you for your quick reply. I will look for the DIRECT LINK option and try that.

I think I'm finally starting to understand how to use imgur. I'm able to display photos here using a direct link.

当初の計画では、昨年中に製作を終え、501st日本支部への入隊を申請し、今年のSWCJに日本支部の一員として参加する予定でした。しかし、時間的な都合でいろいろと都合がつかず、SWCJ開催前に参加するのは非常に難しいと悟りました。今年の初めには、もっとシンプルに鎧を作ろうと考え、細かいことは気にしなければ間に合うかもしれないと考えていました。 しかし、501st日本支部の先輩がこう言ってくれました。「鎧は急いで作ると失敗すると取り返しのつかないことになる。丁寧に作った方がいい」また、「丁寧に作業すれば、完成した時には一生大切にできる宝物になる」と。 それで、私の製作はゆっくりと、しかし確実に完成に向けて始まります。 全てのパーツを削り、切断面を軽くする作業と並行して、TLJ装甲を製作する過程で特徴の一つと思われる上腕部の切断部分の製作に着手しました。これは、このサイトの偉大な先輩方からのアドバイスを聞き逃してしまい、指示通りにパーツをカットしてしまったためです。

みなさんこんにちは。 imgur　という写真を管理する無料のサーバーサイトを 多くの方々が利用していますが、 残念ながら私のPCや回線状況によるものなのか、全くアクセスすることができず利用できません。 アーマーの組み立て進捗状況をお知らせする際に、写真は有効だと考えてるので、 何か別の方法やサイトがあれば、ご享受ください。また、そのようなサイトを利用しなくとも、 ここのサーバーに直接投稿しても構わないのであれば、それにこしたことはありません。 アーマー組み立ての現状は、TLJの特徴のひとつともいえる、上腕部のパーツの一部変形作業をしています。 Hello everyone. Many people use imgur, a free server site for managing photos, but unfortunately, perhaps due to my PC or internet connection, I am unable to access it at all and cannot use it. I think that photos are effective in letting you know the progress of the armor assembly, so if there are any other methods or sites, please let me know them. Also, if you don't mind posting directly to this server without using such a site, that would be great. Currently, I am working on partially transforming the upper arm parts, which is one of the characteristics of TLJ.

I would love to meet you at Celebration Japan. I've followed you on Instagram.

I'm honored. I don't have all the parts yet, so I'm ordering them in as I go.

It's an honor. I'll do my best.

I'm honored. I'm not sure yet, but I'll give it a try.

Thank you. It's an honor.

Nice to meet you. I gave up many times, thought many times, and worried many times, but I bought ANOVOS armor with new hope in my heart, but it didn't arrive even after more than three years across the Pacific Ocean. The company changed, the COVID-19 pandemic occurred, and two more years later, in 2024, the "Denuo novo FOTK TLJ" arrived. I am currently aiming to join the 501st Japan branch, and I will start assembling this armor from now on. Of course, I still don't have enough necessary parts and information. I would like to aim to complete it with the enthusiasm and advice of the many seniors gathered here. Thank you very much for your cooperation. はじめまして。何度も諦め、何度も考え、何度も悩みましたが、新たな希望を胸にANOVOSアーマーを購入しましたが、太平洋を越えて3年以上経っても届きませんでした。会社が変わったり、COVID-19パンデミックが発生したり、さらに2年後の2024年に「Denuo novo FOTK TLJ」が届きました。私は現在501st日本支部への入隊を目指しており、これからこのアーマーの組み立てに取り掛かります。もちろん、必要なパーツや情報はまだまだ足りません。ここに集まった多くの先輩方の熱意とアドバイスを頂きながら完成を目指したいと思います。どうぞよろしくお願い致します。