Jump to content

Jeklynhyde

Member
  • Posts

    76
  • Joined

  • Last visited

Everything posted by Jeklynhyde

  1. I do not have a picture ready for that at the moment, but I will not move along on that until i have posted a pic of the chest for sure!
  2. Was aiming at having the helmet completed by the end of a week, but now I'm debating electronics. I would like to fully deck out the helmet (hearing amp, speakers, fans, static burst/radio chatter) and that's got me thinking that it may be easier to do with the helmet not completely assembled yet. I'm busy digging into the research on that, could go either way I suppose. Also I'm debating on swapping out the flimsy green-tinted film that was provided with something a little more significant. I believe I read somewhere that welder's visor has been used. - In other words, plenty of research still yet to go. A couple other parts I'm stuck on - The forearms were giving me a hell of a time trying to get them glued together. Even after a 24-hour cure time on the E6000, the cover strips kept pulling apart - too much pressure from the curvature for the E6000 to take... I may need to look into ABS cement to get those to behave correctly. As for the chest plate, I think I may cut the neck line slightly deeper to avoid having to cut the bottom edge and recreate the return there. I know it's canon to Mark Hamill's suit to have no return edge, and I know return edge can be restored (looking at Diana's thread), but it's so close to working as is.. We shall see.
  3. So after more than a year's inadvertent hiatus, I'm looking to get back into working on and completing this build. Plenty of time to do so with the COVID thing going on (not that I got out much to begin with anyway). I just wrote up a status update on my profile to give a PSA about mental health. Click my name to go check it out. I think I will start up where I left off with trying to get the helmet completed. Plenty of research to do to get back into the flow of things, but expect updates soon!
  4. I'd like to take a couple minutes to do a

    PSA about Mental Health

     

    It's easy to assume that everyone's life is the model of perfection when you only get to see what small snippets of it that they post online or disclose to you in conversation.

    It's easy to assume that everyone is out there leading a happy life with no strife - or that things just roll off their backs like water to a duck.

     

    But that really isn't the case.

    We've all got struggles. We've all got really hard things to deal with.

    Life isn't easy. Sometimes just being alive is a struggle.

     

    When it comes to mental illness, there are many faces and many variations therein.

    I am someone who struggles with depression. My variation seems to be flared up by stress and can cause a total lack of interest in the things I used to love. It can bring my whole world to a screeching halt. It can make even the simplest tasks difficult to push through, let alone getting out of bed to face another day.

    But the way it is one day is not the way it is every day. I have seen happy days and I will see them again. I have faced difficult times and made it through them, maybe a little worse for the wear, but with new experiences and perspectives on life.

     

    It helps me to think of the flare-ups as growing pains and not just unwarranted anguish and suffering.

    When I find myself in a low spot I encourage myself to take the time for self-reflection. Treat the flare-up as a symptom of some other issue; my body is telling me, "something is wrong". What is making me unhappy? What am I dissatisfied with? What do I need? What am I missing? What would help me out right now, in this moment?

     

    What often works the best is: if someone I cared about felt like this, what would I say to them? What would I do for them? How could I take care of them and lift some of the burden to make things easier?

     

    This is just something that I have to deal with on my trip through this life.

     

     

    So for those troopers that are also suffering or close to someone who struggles, you are not alone.


    Take the time to stop being caught up in the flow of life, put away the distractions, and check in with yourself.

    It might feel like the world is kicking your an impolite person, but hang in there. You will come out on top if you keep persevering. Just take it one week, one day, one hour at a time when you need to.

    Work on self-care. Show some self-compassion. And do your research - the more you know, the better chance you have of dealing with the things that life throws at you.

     

    And openly consider talking with a mental health counsellor if you aren't already.

     

    Additional PSA about Counselling

    I am a strong advocate for counselling.

    Don't be afraid of reaching out for help. Don't let the negative stigmas surrounding mental illness stop you from doing what is right for you.

     

    Seeking professional help IS NOT A SIGN OF WEAKNESS.

    Most people keep their feelings bottled up inside and it takes an immense amount of COURAGE to open up and be vulnerable to another human being. Just ask Brené Brown.

    (Lots of great content from her. If you haven't looked into her stuff yet, seriously check it out. She covers a lot of deep topics but does so with lots of humor interspersed, so it's rather a joy to watch on top of being very informative.)

     

    Counselling is also not just for those that feel that they are at the end of their rope.

     

    Counsellors can help you out if you are feeling stuck in life, are struggling with a specific issue and need guidance, or just feel like you need to talk to someone when you don't feel like you can talk to anyone else. They can help give you coping tools and strategies, provide insight into certain unhealthy behaviours and patterns and advise on how to avoid them in future, and promote healthy lifestyle habits that support growth and reduce flare-ups.

     

    And you don't need to feel bad about "weighing someone else down". They are literally being paid to listen to you and help you out. It's their job. And most professionals get a deep sense of gratification from being able to help people out, no matter how hard the situation.

     

    One caveat is that not all counsellors are the same. Some specialize in different areas that don't apply to you, some have personal views that conflict with your own, some are just bad at their job (they're human too!) - so you may need to do a little "shopping around" to find one that you feel that you connect with and can trust.

     

    Reaching out can be a difficult step and trying to find a counsellor in the first place can be a daunting task. In these days, internet searches are very much your friend. I found my current counsellor through the Psychology Today website and was able to request an appointment via email, but there are many online resources.

     

    Additionally, many companies are partnered with an Employee Assistance Program, or EAP, which can be used by the employee or even friends and family (you don't have to be working for the company that supplied it to use the service). If the process of finding a counsellor is too daunting for you, consider reaching out to an EAP. In some cases they have mental health professionals available, or they can help you locate one close by that is within your financial means.

     

    I am neither religious, nor currently in the education system, but you can also reach out to religious organizations or school guidance counsellors if you feel you need help. Religious organizations may have a certain agenda in promoting their views, but many will offer assistance to those that reach out for help regardless if you are a member or not. These types of individuals are also a good option if you lack the financial means, though professionals often have reduced rates for those that are enduring financial hardship.

     

     

    I've said a lot, and there's really a lot more that I could say on the subject, but I'll save that for another time and probably some other platform.

     

    Stay healthy guys!

    You are loved! And your contributions are appreciated!
     

    - Jeklyn Hyde

    1. JavierPerero

      JavierPerero

      This is very informative. I love these themes. I am interested in understanding psychology .

  5. Ok. So going back through my earlier posts here, I see that some of the photos are breaking. The error being "URL signature expired". So I'm going to consider Facebook to not be a good place to host pictures. So I've taken the time to create a google photos album of all the pictures I've already uploaded. I'm going to go through and update all the pictures in previous posts so that they won't expire again (hopefully). So far, I've replaced all the images in the first post. I'll wait a little while to see if it lasts (or if pictures start majorly breaking - not too difficult to update now that I've got the pictures uploaded to another source location), then I'll update the other posts. In other news: As it turns out, sportsball game stadiums don't like it when you wear masks to their events... even when they're Star Wars themed..... so the pressure is off for getting it done before then. I was side-tracked a bit by realizing that my older pictures were starting to break. But I still plan to get the helmet (I should be saying bucket, shouldn't I?) completed next in line. My current pause point is trying to find the size of drill needed for the rivet holes, haha. I've already set the brow trim to length, but I'll make a separate update for that. Cheers!
  6. When it was first glued in place, it kept contact, but after bending it to assess the lower join, it split away along a fair portion of one edge. One of my friends suggested using Loctite, but I'm not sure how well that would work. Squishing the sides together for the lower join causes this strip to split significantly from the one side. A little bit better view to show the separation. Will need to determine a heat-bend solution. Cut the left forearm cover strip to size. Dry fit testing clamp positioning. And with glue and more magnets. Waiting to cure. Sooooo. In other news, I've been invited to go to a sports-ball game on Star Wars Day. Since sitting for an unknown number of hours in a plastic suit of armour seems non-conducive to either my butt or the plastic, I've decided to shift my attentions to the bucket completion so that I can wear it for the game. So I'm digging into the research on how I wanna do the trimming around the eyes and the frown teeth. I've already purchased some Plasti-Dip so that I can black out the inside of the bucket while it's still in two pieces, as I've heard that it's a lot easier to do that way. I've also been digging into the EIB/centurion request threads and making note of the corrections suggested to others. I'm definitely going to make sure my ears are slanted to match the angle of the brow detail bit at the top and make sure my tube stripes are a pencil width away from the cheek edges. Beyond that I've recently been updating a youtube playlist of all the music I'm jamming out to while I work on things. Right now that's a lot of dance and French music (Stormae in particular - super recommend!), haha. Here it is if you're interested: https://www.youtube.com/playlist?list=PLyG3QoHhi8SfZGwLfNf1Sblj5bx72TY7D And tonight, my drink of choice is Fireball! The rough edge of the mask... Used this as a practice surface for more precise Dremel work before moving on to cleaning up the teeth and eyes. Rough edges of the eyes from the inside. Rough edges of the frown teeth from the inside. Best results from the Dremel are achieved by using the tool like a pencil. I found it easier to get the angles I wanted and see the effect I was creating by Dremeling from the outside in with the eyes. Got me some Plasti Dip. And taped off around the eyes and frown teeth. I didn't think about getting around the other edges till later. Close-up on the tap squished into the frown teeth. And the outside glamour shot. Another view inside of the tape-off. Doing this in a basement with no proper ventilation... Gotta still use the proper PPE. Started spraying without tape to cover the edges and some got on the outside. So I got smart and put tape around the edges for both cap and face. A bit excessive. Turning it around I ended up dripping some excess on the tarp throw and the floor. And now it waits. I did get a little on the outside, but it was pretty easy to scrub off using the painters tarp.
  7. You're making excellent progress Cricket! Awesome job on the grappling box! Keep it up! I'm excited to see more updates
  8. Gluing cover strips on the biceps, one side at a time. I wanted a tight bond, so I got full coverage by using bar clamps and C-clamps AND magnets, haha. THE CLAAAAMPS. Blue tape on the inside keeps any glue from squishing out onto the clamps and is easily removable after cure time. Last one set to cure. Next step is the forearms. The thing that was holding me back from completing the forearms was the overall length. I was debating between trimming the wrist end more, or cutting the elbows out deeper. I think I can manange with a deeper elbow cut. That decision was holding me back from setting a final cover strip length. But I've made the decision, so now I can progress. Taping the inside of the forearm to keep it in place for gluing. Trying to keep the line at the wrist edge even. I taped a couple popsicle sticks together and then to the ends of my bar clamps. I put one of them on the wrong side, but it ended up working anyway XD. "Dry fit" testing out all the clamping gets good coverage before any glue gets involved. Inside view. This will be a little more difficult to get the magnets set correctly once I go to glue this other side. And glue in place and set to cure.
  9. Paints arrived! Turns out I don't think I'll be needing the Gloss 48 (Mediterranean Blue) as this was an old recommendation. But I've got it if I need it. Put all the screws in, taping the brackets to the armour to keep them correctly associated, then painted the ends. This kept the screws from touching other surfaces while drying. Got coverage all around the heads of the screws to account for any face that would still be visible. Set them to the side for close to 24 hours before I installed the first set of brackets on one edge. The paint was still kind of malleable, so I let it sit for a while longer before I installed the rest. Even then the paint still got mussed up a bit. All the back brackets mounted. I squeezed in a little E6K into each of the holes before I screwed everything in place. I should have figured out the straps first so that I could avoid some hand-sewing... Otherwise I would need to take up at least one screw per bracket in order to slide them in . Cut up the elastic for the connections. Temporarily have them kept in place with staples just in case I need to take it apart again for any reason. I may repaint some of the screw heads to cover up what I managed to knick off. At least now I can do better torso fitting. Painted the abdomen button panels!
  10. That looks fantastic! I'm looking forward to that build! It's going to be tons of fun.
  11. I _am_ the accuracy bug xD haha. Thanks for the info! I'll check it out. Just got the screw heads painted for the back brackets. Once they're dried i should be able to get the elastics in place - if the elastics slack out over time,or don't hold things tight enough, i can replace them for nylon then. Also sorry for spam reacts. Finally figured out how to like other people's posts - double-click, geez, haha.
  12. I bent the rest of the brackets into proper form to lie flat. Cut a piece down to size for both return edge width as well as curvature Squeeze out some Gorilla Glue superglue gel Use another piece of scrap plastic as a spreader and get full coverage. Hold it into place and try not to get fingers glued to the armour... Repeat till cry, then drill more holes and mount more brackets. Scuffs on the inside because I drilled from the inside and it was a tight squeeze. Going for the original rivets for the drop boxes, I saw that they were single cap rivets... Looks like that's what it should have been for the whole belt too, but too late there. I was able to use some pliers to remove the "double" cap from the rivets that were included with the RS kit. Punched some holes in the elastics for the drop boxes. On the outside, now a single cap rivet And on the inside, the cap end. Testing out the positioning of the straps and the boxes before things get glued in place. Once I was happy with their positioning, I drew on, then cut out circles for where the abdomen snaps go. In order for the best positioning for the boxes to line up to the outer edges, I ended up cutting out small semi-circles on the other side of the strap as well to account for the outer rivets, and allow more range closer to the end of the belt. I cauterized the open edges of the elastic. Then I sewed around the edges for extra durability. I wiggled the straps into place, put E6000 underneath, just on the interior facing strap edge, and taped them down in case they felt like going places. One note: There is some wiggle room with the inner drop box within the outer box. I drew myself a little picture to figure out which way to squeeze the inner box in comarison to the belt in order to cinch up any possible slack. And that is - if you glue the inner box as far down as possible, it reduces the gap (ever so slightly) between the top of the outer box and the bottom of the belt. I hammered down the rivets to the inner drop boxes, then glued the straps in place, _then_ I glued the inner and outer boxes together. This allowed for the best amount of flexibility in positioning. Strap glued, Drop box gluing. Lined up very nicely with both edges. And the final product. Stage right / Stage left In other news: E-11 came in today! And all of the parts.... This gets to wait for a little while. Maybe until it's a little warmer outside I can paint it in the garage. Tomorrow the paints should come in. I went and bought a sealing iron and some plastic polish as well, so nothing else should stand in my way (except for myself) in my path to completion
  13. I got stuck on the shaping of the kidney section. I can't quite progress with the mounting until I sort out the final shaping (as I would rather install the reinforcing pieces in their final position rather than having to attempt to melty-bend two thicknesses of ABS) but then I realized that the belt will help squeeze the armour a little. I did another test fit and it doesn't look horrible. I may not attempt any more additional shaping. The thinking behind this is that if I cut down the shape the kidney section any more, I will need to trim down the sides. In its current shape, it just manages to meet up with the ab section and it feels snug, yet not constricting. But... if I want to shape it more, I can do so in the future. With the kidney taped to the ab in position, I tested out the chest sizing again. If I cut out the neck a little more, I may be able to get away with not having to cut and reshape the bottom return edge. (We'll see. I may end up trimming it anyway). I suppose I should add: I am somewhere between 5'6" and 5'7".
  14. That sounds like an excellent idea actually. I have read here and there about the returns on the back being prone to cracking. And after seeing the originals with the screw holes needing to be relocated because they tore out (at least that's what seems to have happened), I definitely wanted to reinforce and do what I can to prevent the potentially inevitable.
  15. Using the scrap from the kidney, I cut out small bits for mounting support. following Fragarock's and UKswrath's build threads. I know this isn't movie accurate, but does this affect centurion status? So far, I only did it to the upper back. Can be undone if needed. Superglued them in place on the back. Re-marked the points for the holes. Drilled the them at 7/64. I used a 7/32 drill on the outer return edge to give the holes a little chamfer to countersink the screws slightly. Installed brackets. If you hit this step, before gluing all the screws in place, you may want to cut and attach the elastics so that once you're ready to glue them, you can just slip the other bracket into an already sewn elastic. I did not do this and now I will need to do some careful hand-sewing.
  16. The other battlestation. I started with 200, but eventually boosted it to 250. Time to attack that wobble Started with a more focused tip for the curved section. You can see in the background it's flattened out. For this I ended up using my fingers for the most part. Switched to a wider tip to concentrate on the flatter, longer sections. Curve is a lot flatter now. And I was able to push down the bulge in the middle Flat once again. For the edge, grabbed the wood block, heated up along the edge and pressed it out a bit Used some curved, wide, flat pliers to grab and bend the plastic without removing the heat The gloves allowed me to hold and manipulate the part with my hands or the pliers without any risk to my flesh. Managed to get the cut out curves into shape again too. Heat gun allowed for much better control. Even if I end up cutting more off, it was good to get more comfortable with the use of the tool. I had to mess with it a bit more, but I was able to maintain the overall curve. Matching it to the back, it looks like I'm going to need to do a little more shaping further from the sharper parts of the curve. Also, thank goodness for the editor saving input. I would have had to have rewritten so many posts by now XD
  17. Ramping up the battlestation again. Pot on the right is for cold water bath. Turns out it was more useful for cooling down my hands Full pot, rolling boil. Part of the problem before was that I couldn't get the part shaped quickly enough before it cooled down. Put on some gloves that let me handle and shape the plastic in the water. When the heat got too hot even with the gloves, I dunked my hands in the cool water. Grabbed some popsicle sticks and used pliers to compress the edge. Testing to see that it would work. This would have been easier if I had not trimmed down the return edges so much already, but alas. This is what I've got to work with. Ready to enter the pot. Found a block of wood to try to assist shaping. You can see the popsicle sticks and pliers did the trick to flatten out the return edge. Cut two pieces and played with it for a while. Still wobbly, but in the right shape. Next step may be the heat gun, but now that I know ~200 degrees does the trick to get it a little bendy (but not floppy), I'll start at that temp with the heat gun so that I don't overdo it.
  18. Not yet, but i may need to get one! That is definitely on my list. Thanks for the suggestion!
  19. Thank goodness! Thanks for posting that! I thought i was going a little crazy over here. I hadn't taken very good before pictures or measurements so i was starting to freak out a little. I do have a heat gun which would allow for greater control so long as i can direct it correctly, but i haven't figured the right temperature yet.
  20. Then here's where I go wrong... In reading about the hot bath technique to help shape parts, I traced the outline of the bottom edges (Right from the front, and Left from the front). Smaller dutch oven doesn't allow for quite as much submersion as I was expecting... ... So I got out my big pasta pot. After the first attempt, the left side was still significantly out of place. The right side wasn't as bad... I think the first bath worked decently for it (no before image on this one) After a number of attempts... It's at a better curve, but I'm not liking how curved the top got. The right side managed to get to the right shape But in the process, the left side got way too bent out of shape. The return edge got all curled up. Deformed side To the point where it looks like that whole side is shrunken - Turns out this is part of the lovely asymmetry as part of original casting from the RS armour. ... and warped - Don't worry! This is how it's supposed to look for RS armour. warped.. warped....
  21. Taking a look at the mounting brackets, they're all the same length minus the three super long ones. But they're all skewed, the same side on all of them is lifted up. So I bent the ones I was working with so both sides were on the same plane. Using pliers to hold the vertical part steady and twist the other side in line. I also decided to take off all the stickers from the insides of all the parts. Sticker residue was being a bother. Did a little research, and it turns out WD-40 does an excellent job. Nearly immediately removes the residue and does not damage the plastic. All clean. Once removed, wash it down with dish detergent to remove any residual. Getting the bracket positioning sorted. Following Ukswrath's build thread. Used tape to help draw the second hole mark. In matching the back to the kidney to mark the kidney's lines, I see that they won't line up without significant bend to either the kidney or the back. Kept the brackets used for the measurements taped to the plates in case of any length differences due to the bend reshaping. Using tape to make the kidney bend to a better shape to match the back. With the tape in place, the curve and gap look better. Been watching House in the background - It's the Darth Vader episode XD.
  22. Just made an E-11 blaster kit purchase from DoopyDoos. On the docket for tonight: torso sizing and strapping. Let's see if i can get it done in one shot xD
  23. Maybe i won't have to trim it then. I haven't really trimmed either of the bridge pieces and I've left the return around the front neck edge. We'll see... I won't cut anything down till i get some strapping in place and find out what i can get away with xD. Thanks for the input!
  24. Dry fitting.... Definitely going to have to trim that chest. Womp-womp. In order to get it on without too much trouble, I taped the chest to the back with enough room to fit my head through, so the chest is a little floppy positionally - Correct positioning would be with chest plate nearly in direct contact with the back plate at the shoulders. Chest attached. Side and back view taping return edge to return edge. Back kidney compared to upper back looks a little wide comparatively. Chest not attached. Side views with ab-kidney overlap. Back view. Kidney-upper back looks a little tighter. That booty though XD. I think connecting the crotch will sort the bottom curve out fine.
×
×
  • Create New...