Hunterdisarm

Thank you for the clarification. I will wear my centurion rocker with pride.

Thank you Sly11 and ukswrath for your service to the Legion and FISD. Additionally thank you for the acknowledgment on my completion of level 3 requirements.<br><br> Question:<br> Are EIB/Centurion badge ranks considered to be held concurrently? Or does possessing Centurion replace EIB as a "rank," if you will?

Hunter Nelson TK-81457 FISD: HunterDisarm Alpine Garrison EIB Recipient #613 http://www.whitearmor.net/forum/topic/37981-tk81457-requesting-anh-stunt-eib-status-mtk613/ Mandatory Information: Armor = MTK Helmet= MTK Blaster= Hyperfirm Optional: Height = 5'11" Weight = 150lbs Boots =TK Boots Canvas belt = DIY Hand Plates = Trooperbay Latex Electronics= N/A Neck Seal= Darman Stunt Holster = Darman ANH One call out for "extra credit" Armor Fit/Assembly was to trim my TD clips to conceal under the belt. If I assumed incorrectly that this was only a suggestion, please advise and I will correct for Centurion app. The loose threads (visible below) were remedied as seen in the dedicated belt photos below. Thank you again for your consideration and service to the Legion.

Thanks Joseph! That is a good tip, I picked that idea off another build. You can just *barely* see the loop Velcro peeking out of the side in my TD shot. I've see. What impact the aluminum stock had on other armor!

Additionally, are there certificates available?

The excitement is worth the wait! Thank you for your service to FISD and for awarding me with this honor. I'll have this on the Centurion board shortly, right after I trim down those TD clips

I hope that these are satisfactory! *EDIT* as I am posting these, on my way out the door for work... I see I missed the middle hook on the left shin and the hole is showing. If needed I can re-take this late today fully closed. Please advise, thank you.

Well, updating that bit from my phone seems to have knackered my photos. I'll post those back up in a few hours after work.

Legion profile:<br> <a data-ipb='nomediaparse' href='http://www.501st.com/members/displaymemberdetails.php?userID=21860'>http://www.501st.com/members/displaymemberdetails.php?userID=21860</a>

Hunter Nelson "HunterDisarm" TK-81457 Alpine Garrison http://www.501st.com/members/displaymemberdetails.php?userID=21860%27 Mandatory Information: Armor = MTK Helmet= MTK Blaster= Hyperfirm Optional: Height = 5'11" Weight = 150lbs Boots =TK Boots Canvas belt = DIY Hand Plates = Trooperbay Latex Electronics= N/A Neck Seal= Darman Stunt Holster = Darman ANH FRONT BACK Left Right (the loose threads have been fixed, see dedicated belt photo below) Left Detail Right Detail Helmet Front Left Right Back Mic Tips Backlit Belt (loose strings from above photo have been trimmed and hems sealed) Neckseal Blaster Left Blaster Right D-Ring TD Rear Action Shot Strapping Cod/Butt Abdomen Detail Thank you for your consideration. I am ready to respond to your feedback.

TK 81457 Requesting access.<br><br> Member Prof.<br> <a data-ipb='nomediaparse' href='http://www.501st.com/members/displaymemberdetails.php?userID=21860'>http://www.501st.com/members/displaymemberdetails.php?userID=21860</a><br><br> Best Regards

My MTK kit finally shipped, so I'm going to post my WIP now.<br><br> This is my first build and I am aiming to build for Centurion. If there are any points of screen accuracy beyond centurion requirements, please share? Armor: MTK (Shipped) Helmet: MTK (Shipped) Boots: TKBoots (On-Hand) Under Suit: Under Armour (OH) Belt: DIY (OH) Holster: Darman (OH) Neck seal: Darman (OH) Blaster: Hyperfirm (Ordered) Here is the belt I crafted as I wait for my kit to arrive. Layers of fraying canvas, white denim twill weave outer and white satin lined. Just like the originals according to my research. I cut the strips 8cm wide. I added a layer of very heavy fusible interfacing that I cut slightly narrower than the canvas I pinned the inner 4 layers together and stitched about an inch in to reinforce everything. Then I pinned the denim strip and folded over my satin liner and stitched them in one go. I also whipped up some wire brackets for my elastic setup: