Darren TK-11916

Congratulations Dale!

Wow. Thank you thank you thank you! I greatly appreciate your consideration and acceptance. Also, a huge thanks to everyone who helped me along the way. UKSWRATH I couldn't have done it without your tutorial and one on one help along the way. Now I'll shut up and troop.

I re-shot those angles. I think they are improved over what I posted last week. With that said, I feel I need to apologize. I'm going to submit these, but I fear they aren't up to Centurian standards. I find myself terribly frustrated with these gaps. I honestly do not think it's the armor or the build. It's me. To be more accurate, there is too much me. Looking back to my Basic photos in April, this issue was not there. If you cannot approve, I totally understand. I'm going to get back to the gym, start getting miles on the road and get back to fighting weight. When I do, if you would allow, I'll resubmit. In any case, here are my re-takes. Thank you for your time and thank you for allowing me the chance to make the correction. ~ darren

Yes no problem. I'll be able to do that tomorrow evening at the latest. Thank you!

Darren Mullen 501st ID- TK-11916 FISD Forum Name- Darren TK-11916 70th Explorer Garrison Armor Maker- Anovos Helmet Maker- Anovos Blaster Type- Hyperfirm Elite Height- 5'10" Weight- 220 Boots Maker- TKBoots Canvas Belt- TKittell Hand Plates Type- Latex Electronics- Aker/Icomm & UKSWRATH fans and SHA Neck Seal Type- Anovos Holster Maker- Anovos 501st Legion Profile: http://www.501st.com...hp?userID=20951 EIB Link: http://www.whitearmor.net/forum/topic/36732-tk-11916-requesting-anh-stunt-eib-status-anovos-567/ FRONT ACTION PHOTO LEFT SIDE REAR RIGHT SIDE LEFT AB/KIDNEY, HOLSTER DETAIL RIGHT AB/KIDNEY DETAIL AB BUTTON DETAIL INTERNAL STRAPPING SHOULDER BRIDGE DETAIL INTERNAL STRAPPING COD CONNECTION COD CONNECTION FOREARM & WRIST DETAIL GLOVES WITH LATEX HAND GUARDS (TrooperBay) GLOVES & FLEXIBLE HAND GUARDS THIGH AMMO PACK THIGH AMMO PACK SIDE & INTERIOR THIGH AMMO PACK SIDE & INTERIOR SNIPER KNEE SNIPER KNEE SIDE SNIPER KNEE SIDE BELT BELT INTERIOR & AMMO PACK REAR NECK SEAL HELMET FRONT HELMET LEFT HELMET REAR HELMET RIGHT HELMET HOVI TIP & VOCODER DETAIL FROWN DETAIL HELMET EAR SCREW DETAIL LENS COLOR S-TRIM THERMAL DETONATOR THERMAL DETONATOR BACK THERMAL DETONATOR BACK SCREW DETAIL BLASTER BLASTER BLASTER, D-RING, COUNTER & SCOPE DETAIL Thank you for your consideration. Respectfully submitted, Darren Mullen, #TK 11916 Wichita, Kansas

FANTASTIC! I'm thrilled and honored to be accepted for EIB. Thank for your compliments and your suggestions for improvements. I'll get right to work and see you at the next step.

Sly11, I made the alterations and adjustments as you suggested. The photos of those corrections are below: Cod and Butt plate connection hardware paint removed: Shoulder bell to chest plate and shoulder bridge gap narrowed: Back plate to kidney plate uneven gap corrected: Thank you for your suggestions and allowing me the opportunity to make the needed corrections. Darren Mullen

No worries.<br><br> Sounds good. I'm on it. Thank you

I hear what you're saying and I see your point. I've waffled back and forth on that. I used starwarshelmets.com and the ANH helmet examples as a reference, and I saw that nearly every frown was slightly different from bucket to bucket. So then I just went with personal preference and stopped when I liked how it looked. If the reviewers suggest I paint a little I will.<br><br> Thanks for your thoughts!

Sounds good allan1313! Thank you. That paint comes off easily enough. No problem there. Guess I thought if a little while paint here and there was good, more everywhere would be even better. And the eyes, I've been back and forth myself with those. My thought process being, less is more, and it's better to take off too little rather than too much. Thanks for your feedback and your advice!

Name: Darren Mullen 501st TK ID: 11916 FISD forum name: Darren TK-11916 Garrison: 70th Explorers 501st Legion Profile: http://www.501st.com/members/displaymemberdetails.php?userID=20951 Armor Maker: Anovos Helmet Maker: Anovos E-11 Blaster: HFx Elite Height: 5'10" Weight: 200 pounds Boots: TK boots Canvas belt: Kittell Hand Plates: Trooperbay Electronics: iComm w/ Aker Amp, UKSWrath fans, UKSWrath SHA system ordered Neck Seal: Anovos Holster: Anovos PHOTOS FULL BODY: ACTION SHOTS: ARMOR DETAILS: HELMET DETAILS: ACCESSORY DETAILS: BLASTER DETAILS: Thank you for your consideration. Respectfully submitted Darren Mullen Wichita Kansas

TK-11916 respectfully requesting 501st access http://www.501st.com/members/displaymemberdetails.php?userID=20951 Thank you!