AbrahamLINC0LN
Member-
Posts
52 -
Joined
-
Last visited
About AbrahamLINC0LN
Contact Methods
-
Skype
Abraham LINC0LN
Profile Information
-
Gender
Male
-
Location
Long Island, NY
Standard Info
-
Name
Shawn
-
My AP armor build [*AP]
AbrahamLINC0LN replied to AbrahamLINC0LN's topic in Build Threads Requireing Maintenance
My kit came pre-trimmed. Do you know where I can get ABS of a similar quality out in a store? -
My AP armor build [*AP]
AbrahamLINC0LN replied to AbrahamLINC0LN's topic in Build Threads Requireing Maintenance
Jeep frog - what did you use for the kidney? Spare ABS from your build or did you get the plastic somewhere else? -
My AP armor build [*AP]
AbrahamLINC0LN replied to AbrahamLINC0LN's topic in Build Threads Requireing Maintenance
So as of now I have the forearms, biceps, shoulders done. Vader Dave Ab buttons on chest plate. Shins curing now. Love those magnets. Snap plates on kidney top, biceps, shoulder bells, chest to back bridge with white strap. thermal detonator is done with metal clips. Still need to: Snap plate on forearms, sniper plate, thighs, chest strapping, kidney shims, crotch tabbage, Han button, thigh to Ab snaps -
My AP armor build [*AP]
AbrahamLINC0LN replied to AbrahamLINC0LN's topic in Build Threads Requireing Maintenance
Where do you recommend I put the foam on the armor - on the outside side of all armor (pushing it away from the ab)? -
My AP armor build [*AP]
AbrahamLINC0LN replied to AbrahamLINC0LN's topic in Build Threads Requireing Maintenance
From Beren's post, it looks like the front of the thighs were glued and finished and then he dealt with the back alignment. Is this correct? When I try to match up my thighs, it looks like the most importnt thing to consider is the front of the thigh that shows. Shouldn't the front seams have matching/opposite angled cuts? -
My AP armor build [*AP]
AbrahamLINC0LN replied to AbrahamLINC0LN's topic in Build Threads Requireing Maintenance
I checked it out and retread it three times. Sadly my AP thighs have a different cut than yours it seems. Can you or anyone else offer their thoughts based on the above picture? I feel like it might be as lined up as it will get. I need confirmation, validation, or opposition to just glueing it as is. -
My AP armor build [*AP]
AbrahamLINC0LN replied to AbrahamLINC0LN's topic in Build Threads Requireing Maintenance
So I mocked up the right thigh. Can someone give me advice on how you think I should trim? -
My AP armor build [*AP]
AbrahamLINC0LN replied to AbrahamLINC0LN's topic in Build Threads Requireing Maintenance
So I met with CureMode and got to talk to him about the build. I was glad to meet a fellow fan and to see his armor up close.Now I have a better understanding of test fitting and how to proceed with my build. I ordered 20 N52 magnets, and while I wait for those to come in the mail, I'm going to glue on all my inner shims and use the lil ABS squares that came with my kit to make a buttload of snap plates. My biceps can be finished if I can find the time. I'm hoping ot have my biceps, forearms, shins and thighs done this weekend. I'll put up pictures when I get that all done. -
My AP armor build [*AP]
AbrahamLINC0LN replied to AbrahamLINC0LN's topic in Build Threads Requireing Maintenance
I have small hands. I know my wrist will wiggle through. I think I'm going to have to trim the top of the forearm to the first groove. I feel like when I bend my elbow, if it was to that point, i could bend my elbow completely. -
My AP armor build [*AP]
AbrahamLINC0LN replied to AbrahamLINC0LN's topic in Build Threads Requireing Maintenance
I trimmed down the forearms and glued inner shims on each. When it cures, i'll dremmel the excess off. -
My AP armor build [*AP]
AbrahamLINC0LN replied to AbrahamLINC0LN's topic in Build Threads Requireing Maintenance
So I trimmed down the forearm to roughly 13 mm on each side which leaves a reasonable amount of space on each side of the cover strip. When I rest the piece on my arm and bend, it pinches a lot. How much trimming by the elbow do you suggest and what kind of trim do you suggest: shave off the top or round down the part that stabs my elbow? -
My AP armor build [*AP]
AbrahamLINC0LN replied to AbrahamLINC0LN's topic in Build Threads Requireing Maintenance
After a few hours of messing around with the trimmed pieces and sanding, I have a question for you experts. On the forearms, I have something like 20-25 mm on each inside end that I am to butt join. Do I need to trim that down more to like 8-15 mm per side? For all other arms, shins, legs, do I want to trim them all down to have the cover strip covering most of the face of where the pieces join? -
My AP armor build [*AP]
AbrahamLINC0LN replied to AbrahamLINC0LN's topic in Build Threads Requireing Maintenance
also note, I was sent cover strips for all parts. He even included some black elastic and black chem gloves. I probably should have asked him while trimming to round the ammo on the knee and cut the belt at 45 degree angle, but oh well, I can cut and sand those beasts down myself. I'm curious how the sniper plate will mount. Obviously, stay tuned. -
My AP armor build [*AP]
AbrahamLINC0LN replied to AbrahamLINC0LN's topic in Build Threads Requireing Maintenance
Well the UPS guy showed up today and a big grin shot over my face. Insert obligatory box pic here: Box opened: Pieces out of the box still wrapped: Since this armor was purchased trimmed, I am looking forward to seeing how each piece fits. Though one thing I noticed already was RETURN EDGES!!! my pops was holding that chest plate up I got a lot of stuff going on this weekend, so as much as I'd love to just disappear into nerd-vana and just get this armor built, I have to wait a few days. But rest assured, I will be unpacking the pieces and ooh-ing and ahh-ing and marvelling at the awesome shiny new armor. Props to TK-1336 for making my day. -
My AP armor build [*AP]
AbrahamLINC0LN replied to AbrahamLINC0LN's topic in Build Threads Requireing Maintenance
Well my armor has been shipped, expecting arrival Friday. Too bad I am busy all weekend I had this kit pre-trimmed, so I am curious as to how much re-working/cutting/sanding is required. I hope he sent extra ABS cuts for cover strips. Correct me if I'm wrong, but can't the excess plastic from re-sizing pieces function as a cover strip? How do you all like to start an armor build? Forearms --> Biceps --> Shins --> Thighs . . . .