-
Posts
18 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Articles
Media Demo
Posts posted by Hoggzman
-
-
Thanks Glen :-)
-
Wooooooppwooopwoooppppp!!
Thank you SO much!
I will have some time next week here as it's half term holidays, so I will be cracking away at those improvements.
Thank you for the very detailed feedback, it will help me on my journey to Centurion hopefully :-)
I may celebrate with a beer now :-)
-
Thanks Jim!! Certainly was fun to do, and to troop in, a WHOLE different ball game to Vader :-)
-
Thanks Matt, easy to do if required. ;-)
Yes, been looking at TK Boots, seen a couple of the guys with the shiny ones, think overall the TK ones looked best.
:-)
-
Thanks everyone!
Yes, I will lower that a bit, but won't be able to too much as I don't want to see the holes left by the old snaps ;-)
Drop boxes have in fact been raised to meet the belt since those clearance pictures were taking, they sit here now....
Would the paint on the crotch rivet have an impact on Centurion or EIB? I say that because I know it's not screen accurate, but I wanted a super white clean an shiny perfect Persil Trooper look ;-)
Thanks again guys :-)
-
And so I am!! Actually hadn't spotted that until just now, TBH it was a very quick kit up for pictures, my bad! :-)
The biceps, yup, quite roomy at present, but I'm addressing that by increasing my arm size instead of decreasing the armour as part of my quest to be a better Vader too ;-)
-
Name : Steve Braund
TKID : 12212
Forum name : Hoggzman
Garrison : UKG
Armour : RS
Helmet : RS
Blaster : Doopydoos full kit.
Height : 6'
Weight 13st 2
Boots : RS
Canvas Belt : RS
Hand plates : RS latex
Neck seal : Made by me
Holster : RS
FULL BODY SHOTS
Front
Left
Rear
Right
DETAIL SHOTS
Ab buttons
Left kidney / ab
Shoulder bridge
TD
Neck seal
Gloves
Belt
Holster
Cod strap
STRAPING
Internal chest
Shoulder elastic
BLASTER
Left
Right
Spring
HELMET
Front
Left
Rear
Right
Hovi tip
Lens
Aaaaaaand ACTION!
There's one, set for stun....
Thank you for your consideration folks. :-)
-
TK12212 requesting access to apply for EIB please.
http://www.501st.com/members/displaymemberdetails.php?userID=15706
-
Next I had a crack at a bicep. I measured and trimmed and measured and trimmed to get the correct fit round my arm, keeping a return edge on the top part of the bicep
but removed the return along the bottom edge
as this seemed after some research to be the way that were on screen, and also because it will help me bend my arm without too many pinches. I will use some internal foam to pad these out as I wanted to allow room for my arm to get bigger...
To join the two halves I've used 15mm cover strips and butt joints as recommended, the corners of the strips just slightly rounded.
Next with these I will add some internal strips to add overall strength.
-
Next I trimmed the end caps and the centre plate down for the thermal detonator / O2 canister on the belt.
Easiest way I found to do this for the centre plate was score the circular part, then cut up to it, almost creating teeth, which could then be bent backwards and snapped off, them sanded flat.
Next, I cut the end caps down, sanded and popped these on, E6000 the centre plate in position after sanding that smooth at the edges, and firmly strap in place for 24 hours curing time.
-
Hi all.
So, for the troops where I can't do Vader, and to annoy my Wife ready for when she's built her Jawa, I decided it was time to build myself a TK.
After lots of research, asking questions and thinking about the finish I wanted, I decided to go down the idealised TK route, what I imagined, rather than what they actually looked like on screen, controversial I know, but there we go.
So I ordered myself a set of RS PVC from the lovely, and very nice to deal with, Rob, Si and Andrea at RS.
Just a matter of a few days later, this little beauty arrives....
Very exciting!
So, here we go....
I've decided to start with the shins.
I've cut my two 20mm wide front cover strips, trimmed the return ages on the inside top to a first pass (I may trim down more after a test fit, but I figure it's sensible to trim less than more, you can't glue it back on when it's gone) and clamped together shin number one overnight with good old E6000.
To get the front strip in the position I wanted, I offered it up to the shins, and marked the inner most edge where I wanted it (furthest away from the edge) the measured 10mm out, and marked here. I figured 10mm on each shin side = 20mm, which should give me a nice central strip without too much flat front shin poking out either side, I wanted a nice curved look to the front as I'd seen in most reference photographs I've studied.
This is where I'm at right now.
Not a lot, but it's a start :-)
-
I'm wrestling with the same decision here, this post has been very useful, thanks to everyone who contributed.
Still haven't decided however...;-)
-
Hi Sam. Yeah I'm glued to their forum right now, some uber useful stuff there and some lovely people, just like here.
Sure thing mate yeah, would love to help you out if I can, I'll happily pm you any little gems that I find along the path to the dark side ;-)
-
Thanks Kevin, I have indeed applied over there too.
Can't tell you how excited we are about this here, can't wait to get suited up for the first time. :-)
-
Hi all, I'm Steve, I'm Claire's other half.
I'm actually looking to put together a top notch set of Vader armour to accompany by better half. I don't know if anyone on here has any advice, or would know anyone that does, as I'm keen to do a good job!
Many thanks everyone :-)
-
Ahh hello, don't I know you from somewhere?
Request EIB certificate
in Request Expert Infantry Status
Posted
Steve Braund 12212 EIB A4
Thanks and nice to meet you at MCM Mathias, I was the guy with the long hair and beard in the RS PVC ;-)