Viko2307 Posted September 24 Report Share Posted September 24 (edited) Hello everyone. I am writing from Peru to ask for help and opinions on the parts of the armor I am making. It is a new personal project for this year. I would greatly appreciate your opinions and advice. https://drive.google.com/drive/folders/1x8xGKPWGw87yB7lB043U-ITC19w04lAG Edited September 24 by Viko2307 Link Quote Link to comment Share on other sites More sharing options...
gmrhodes13[Staff] Posted September 24 Report Share Posted September 24 Hello what make is this armor, it looks very soft in the details Same helmet different thread See how soft the details are compared with screen used Quote Link to comment Share on other sites More sharing options...
Viko2307 Posted September 25 Author Report Share Posted September 25 (edited) hace 4 horas, gmrhodes13 dijo: Hola, ¿de qué marca es esta armadura? Se ve muy suave en los detalles. Mismo casco, hilo diferente Vea qué suaves son los detalles en comparación con la pantalla utilizada It is not from any brand. It is a handmade work. I cannot upload files to the forum because they tell me they are too big. However, everything is in the drive link that I shared. Edited September 25 by Viko2307 Faltó texto Quote Link to comment Share on other sites More sharing options...
gmrhodes13[Staff] Posted September 25 Report Share Posted September 25 7 hours ago, Viko2307 said: It is not from any brand. It is a handmade work. I cannot upload files to the forum because they tell me they are too big. However, everything is in the drive link that I shared. Normally we use a free online image host such as Imgur, upload your photos there and copy the links into the thread Once again very soft details on your images, you also molded the ab plates to the abdomen, these should be separate, posterior doesn't look right Very soft pull, especially the O Thigh ammos strip mounted incorrectly Sorry I don't have time to go through every photo, perhaps post a build thread Quote Link to comment Share on other sites More sharing options...
Nairy[Staff] Posted September 25 Report Share Posted September 25 The back plate looks very small, the kidney plate also looks quite large! Quote Link to comment Share on other sites More sharing options...
Viko2307 Posted October 1 Author Report Share Posted October 1 After / Before the helmet 1 Quote Link to comment Share on other sites More sharing options...
gmrhodes13[Staff] Posted October 1 Report Share Posted October 1 1 minute ago, Viko2307 said: After / Before the helmet Image is too small to see any details Try uploading to Imgur then copy and paste the link into your thread Quote Link to comment Share on other sites More sharing options...
Viko2307 Posted October 1 Author Report Share Posted October 1 hace 32 minutos, gmrhodes13 dijo: Image is too small to see any details Try uploading to Imgur then copy and paste the link into your thread https://imgur.com/gallery/UbcWgEi Quote Link to comment Share on other sites More sharing options...
dblcross[TK] Posted October 2 Report Share Posted October 2 The after looks like a totally different helmet. 1 Quote Link to comment Share on other sites More sharing options...
Nairy[Staff] Posted October 2 Report Share Posted October 2 Quote Link to comment Share on other sites More sharing options...
gmrhodes13[Staff] Posted October 2 Report Share Posted October 2 Some information and references to compare with screen used helmets http://www.starwarshelmets.com/original-ANH-Stunt-Stormtrooper-armor-helmets.htm Ear bumps and mouth should be gloss grey, note no paint on gums Also refences in our gallery Some details from the CRL, some higher level requirements you may wish to address: Helmet Frown is painted gray and does not leave the teeth area. A total of 8 cut outs in the teeth area of the frown are present. OPTIONAL Level two certification (if applicable): Ideally, the tube stripes are positioned approximately a pencil width from the side of the cheek. Fall of tube stripe tops ideally lean toward the front. Correct Aerators/Hovi-MIX tips are present. Screens used shall be of a wide type mesh, with the rim of the mic and the inside white or painted white. OPTIONAL Level three certification (if applicable): Ear bars shall have only one bump painted in black (rank stripes). Ideally, placement of ears (and screws) should closely follow the rear angle of the trap above them Rank stripe Fall tube stripes, pencil width The "ideal" ear placement is as seen below, where the screws line up with the rear angle of the trap right above it. Because some armorers design their helmets differently or send them pre-assembled this is not always possible to achieve, but it is suggested that you try to get as close as you can. Note: Top ear screws should ideally be located directly below the rear of the trap. Brow trim open at rear Hope the information is useful for you 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.