Jump to content

Request pre approval - TK24079 - imperial shock trooper


Recommended Posts

Hi guys 

hope you are well ? 
 

TK24079 requesting pre approval for a TK shock trooper lvl1 

(already TK in French Garrison ANH stunt)


I've followed several build here in the forum

 

details and pcs  

- Armor and helmet from DA props (build myself)

- gloves Mappa 

- hand guard type ESB 

- boots from Keep trooping 

- DLT19 from RS props master 

- thermal detonator part DA props build myself 

- Canvas Belt from Artneoes (Etsy) Spanish member 

 

Picture attached on the folder link below


https://postimg.cc/gallery/nB8RXFV
 

Thanks for your time and feedback guys 

warmest 

 

Edited by bubuc44
Link to comment
Share on other sites

Hello Alexandre, 

 

Your armour looks great and other than some minor dressing issues, I feel it will be good for basic approval. My only concern that you may come across with approval could be the degree of weathering,  The CRL calls for light scuffing or battle worn.  Your armour appears to be more weathered than most I have seen but ultimately it will be up to your GML to decide if it is too weathered or not.

 

With respect to dressing, your left shin is not closed completely at the back and your right shin is sitting a bit high.  With the red shin and white velcro for closure, the opening becomes much more obvious as compared to all white TK's.  With your right shin up slightly, it highlights the colour difference from wear on your boot.  Some have used velcro on the front of the boot to hold the shin in place. 

EMxId4R.jpg

 

Your forearms cold also come up slightly to make the gap between the biceps and forearm the same as the gap between the forearm and hand plate. Your left side looks good, the right needs slight adjustment.

 

ysF4vUt.jpg

 

 

Link to comment
Share on other sites

Thanks for your reply @Doggydoc and for your time in my review :) highly appreciated 

 

theses elements highlighted apears to be mainly dressings issues correct ?
 

regarding : the right hand forearm (your right) it’s too low I had to put it a bit higher

and regarding the Velcro and high / gap of the leg (I’ve attached other picture on the link below but yeah had to put it on alone…) I’ve fold my right leg a bit on all pictures as I did not adjusted it properly during my try and it was annoying me .. sorry for that 


link

https://postimg.cc/gallery/Ppk0myp

 

about the weathering I’ve got your point but I’ve taken as reference build here in the forum and it appears that there is some with a good weathering to (attached in the previous link a pictures of our brother @zv288bot and his Shocktrooper) and indeed mine is a bit heavier I agree with you but still not a sandy 😅 (at least not as mine)

 

the build I am talking about 


Except theses “dressing elements” and I have to apologies for that as dressing alone is always such a journey especially with a new armor… and I guess also the fact that my neck seal is unfortunately not properly put on the inside of the armor (cf back picture) do you see any major element to review to process with a validation request ? 
 

and again : thanks for your time and help in this :) highly appreciated again

warmest 

 

 

Edited by bubuc44
  • Like 1
Link to comment
Share on other sites

5 hours ago, bubuc44 said:

Canvas Belt from Artneoes (Etsy) Spanish member 

 

The belt should be made from nylon/cordura or nylon/cordura-like material.

 

From the TK Shock Trooper CRL:

  • The soft belt proper is tightly woven nylon/cordura like/style material or material with a tightly woven nylon/cordura like/style covering. Size must be 2.25" (57mm) to 2.5" (64mm) wide. The color is to be white to off-white.
Link to comment
Share on other sites

33 minutes ago, Tilheyra said:

 

The belt should be made from nylon/cordura or nylon/cordura-like material.

 

From the TK Shock Trooper CRL:

  • The soft belt proper is tightly woven nylon/cordura like/style material or material with a tightly woven nylon/cordura like/style covering. Size must be 2.25" (57mm) to 2.5" (64mm) wide. The color is to be white to off-white.

thanks for your response brother 

 

perdon my French : belt is not canvas / coton but is off white and Cordura . Sorry wrong fabric word 

regarding measurement it is exactly 64 mm 

IMG_3134.png

Link to comment
Share on other sites

21 hours ago, bubuc44 said:

theses elements highlighted apears to be mainly dressings issues correct ?

Yes, they are just dressing issues and should be easily fixed.  Not sure if you have elastic between your biceps and forearms, but that helps a lot with spacing. 
I totally understand the dressing alone issues. 

Link to comment
Share on other sites

Yes I do (below picture) 

 

 

 

the only elastic I don’t have because it’s not required on the ROTJ style are the one that are around the biceps and the shoulder bells .(and I had to say they are useful on my other Tk and TD)

 

what I will do is in a close future during a trooping I’ll ask to one of my garrison brother to do picture with me and will review and post everything here 

 

again, many thanks for your valuable feedback which are highly appreciated 

IMG_3154.png

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...