Jump to content

TK23108 requesting ANH Stunt EIB status [AP] (Inactive)


Recommended Posts

Armor maker: AP commissioned build

Helmet maker: AP commissioned build

Blaster maker: Quest Design

 

Bart Busse

https://www.501st.com/members/displaymember.php?userID=36154&costumeID=124

5'10"

155 lbs

Boot maker: Imperial Boots

Canvas belt supplier: AP

Handguard supplier: AP

Holster maker: AP

 

Photos:

 

Front/Back:

 

ErbaXIJ.jpg

iX5KL72.jpg

 

Left/Right:

dSq7vIx.jpg

16iCI1J.jpg

 

Left/Right arms raised:

 

y3DgMxI.jpg

L0UjPlh.jpg

 

Action shots (don't have the hang of that yet, take your pick):

 

0J3sand.jpg

3XhK8jf.png

Wog5dS4.png

 

Ab button close up:

JsOzImP.jpg

 

Cod & posterior connection:

 

2t1bltr.jpg

 

Interior strapping:

 

XDTxyJu.jpg

 

Wrist openings:

 

D8O0jkq.jpg

 

Helmet left/right/front/back:

 

afNtwU2.jpg

x2bp4u2.jpg

kYySVd2.jpg

dCWnEqh.jpg

 

Backlit helmet lens:

 

jYJcttY.jpg

 

Hovi tip close up:

 

sTejesB.jpg

 

Neck seal:

 

2JVZFH5.jpg

 

TD front and back:

 

SH1fwS9.jpg

UQiV7hD.jpg

 

Holster and belt (riveted to ab plate from  AP):

 

0mn0Wtg.jpg

KkHXnvz.jpg

ujxmv9R.jpg

yveiXPv.jpg

 

Boots:

 

huTcHEZ.jpg

 

Gloves:

 

b9UJgpK.jpg

 

Blaster left/right/back:

 

Wupg9BA.jpg

B55pWFj.jpg

bpAcl0o.jpg

HGhbT5c.jpg

 

Additional photos:

 

jsNiHKV.jpg

zrCmcdo.jpg

 

tTpnzMh.jpg

D5JxeLf.jpg

 

rtzRXxj.jpg

pVaEfLH.jpg

k0Ok67I.jpg?1

 

If there is anything missing please let me know.

 

Thank you for your consideration.

 

Bart

 

 

 

 

 

 

 

Edited by BAZINGA
added photos
Link to comment
Share on other sites

Nice work trooper, a few photos I know the DO's like to see:

 

Sniper plate front, side and side

Thigh ammo strip rivets inside and out

Also side Ab/Kidney rivets 

 

Good luck with approval

Awesome background by the way :duim:

  • Like 2
Link to comment
Share on other sites

Oh, they weren't on the checklist but I didn't look to see they are in the photo examples so will add them.  

 

Thanks.

 

Bart

 

P.S.  I couldn't crop in Imgur.  I would have preferred to clean them up more.  However, thank!

Link to comment
Share on other sites

  • Chemi changed the title to TK23108 requesting ANH Stunt EIB status [AP]
19 minutes ago, BAZINGA said:

Oh, they weren't on the checklist but I didn't look to see they are in the photo examples so will add them.  

Full checklist here ;)

 

 

  • Like 1
Link to comment
Share on other sites

Hi Bart, thank you for your request.:jc_doublethumbup:

 

A few more photos would be helpful.;)

 

-A photo of the 6 side rivets. Something like this:

 

qKoTYE8.jpg

 

 

-Photos of the belt, from both sides, where the plastic belt ends and an image of the belt from behind. Like these:

 

NuUwsOZ.jpg?1    cJlBKOX.png    1J5bz8F.jpg     yPiWS2c.jpg?1

 

 

-A "more frontal" photo of the blaster (side of the counter), like this:

 

 

udtK1ak.png

 

Thanks!!!:salute:

Link to comment
Share on other sites

Belt is built as permanent attachment so can't remove it.  I can show the other side of it from the back, the holster side is already in the photo set.  I'll get the other ones uploaded when I can and post when done.  Thanks.

 

Bart

Link to comment
Share on other sites

 

Hi Bart. We must ask one more favor of you, before we can "move along" with your application. We believe that the dimensions of your TD are not accurate.

 

The CRL states for Basic Level: 

length is approximately 7.50" (190.5mm).

End caps are approximately .78" (20mm)in width.

The thermal detonator is attached via metal or metallic-appearing clips, approximately 1" (25mm) wide.

 

Your end caps appear to be too thick. You must trim them a little so that they measure approx. 19mm.  I attach a reference image where you can see the approximate measurements.

 

                                                                                                                                                        Reference images

cFPWSVw.png           MCkPq9g.png   PNEgG5u.png

 

 

                                                                                                                  Reference image

7VKFiJp.jpg

 

 

Thanks Bart.:salute:

Link to comment
Share on other sites

I just checked and the dimensions are off as you observed.  Unfortunately that change is beyond my ability to make at this time and it will just stay as built by AP.

 

Thanks for the consideration.  If I am able to find someone to correct it I will update at that time.

 

Bart

Edited by BAZINGA
grammar
Link to comment
Share on other sites

1 hour ago, BAZINGA said:

I just checked and the dimensions are off as you observed.  Unfortunately that change is beyond my ability to make at this time and it just stayed as built by AP.

You could always reach out to AP (Mark) and ask what glue (if any) he used to keep the caps on, sometimes they are just tightly fit with no glue, this would make it easier to remove with a twist and trim.

 

AP and ATA both use a narrower tube than many other makers or in fact the actual screen pipes, this can make gaps look even smaller.

 

I have manage before to trim the end caps on a TD that was glued, I ran a blade around the inside of the cap and it help pry it loose, may be an option, make sure you put some tape on first so you are scratching the pipe.

Link to comment
Share on other sites

  • 6 months later...
  • Chemi changed the title to TK23108 requesting ANH Stunt EIB status [AP] (Inactive)

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...