Jump to content

TK-61102 requesting ANH TK Stunt Centurion status (Anovos)


Recommended Posts

Name: Christine Harris 

Armour: Anovos 

Helmet: Anovos

Blaster: Resin Blaster

EIB thread:

https://www.whitearmor.net/forum/topic/36821-tk-61102-requesting-anh-stunt-eib-status-anovos570/

 

Height: 5’10”

Boots: TKboots

Canvas belt: Custom

Hand Plates: Silicon 

Electronics: N/A

Neck Seal: Custom 

Holster: Anovos

 

Hello, thank you for taking the time to consider my TK build for Centurion. 

 

I built this kit to Centurion level when I originally built it in 2016. Due to health issues and then the pandemic my application was delayed….I am FINALLY doing it!! I have read over the requirements and found a couple changes that have been added since 2016, which I went ahead and updated. 

-painted my mic tips outer edge white

-glued abs backing behind the lower thigh ridges and will be adding slurry next to cover.

 

Please note: My bucket S trim is glued so it can't be lifted easily for a photo. I posted a pic of the obvious extra ridge the S trim has but if you need a photo of the inside of the trim, let me know, I'll need to peel the glue. 

 

PXL_20220914_161043583.MP.jpg?dl=1

PXL_20220914_161142237.MP.jpg?dl=1

(above) my driveway is sloped a bit that's why I may look a tad crocked in the butt. 

 

PXL_20220914_161921972.MP.jpg?dl=1

PXL_20220914_161952301.MP.jpg?dl=1

PXL_20220914_161921972.MP~2.jpg?dl=1

PXL_20220914_161952301.MP~2.jpg?dl=1

PXL_20220916_121652633.MP.jpg?dl=1

PXL_20220916_121726356.MP.jpg?dl=1

PXL_20220914_135338736.MP.jpg?dl=1

PXL_20220916_121850133.MP.jpg?dl=1

PXL_20220914_135441398.jpg?dl=1

PXL_20220914_135426390.MP.jpg?dl=1

PXL_20220916_121943007.MP.jpg?dl=1

PXL_20220914_151733767.MP.jpg?dl=1

PXL_20220914_151730306.MP.jpg?dl=1

PXL_20220916_122103009.MP.jpg?dl=1

PXL_20220916_122131874.PORTRAIT.jpg?dl=1

PXL_20220916_122605733.PORTRAIT.jpg?dl=1

PXL_20220914_140449470.jpg?dl=1

PXL_20220914_181012082.MP.jpg?dl=1

PXL_20220916_122631688.PORTRAIT.jpg?dl=1

PXL_20220914_135841041.MP.jpg?dl=1

PXL_20220914_181021535.MP.jpg?dl=1

PXL_20220914_135755527.MP.jpg?dl=1

PXL_20220914_135508697.MP.jpg?dl=1

PXL_20220916_122640258.PORTRAIT.jpg?dl=1

PXL_20220916_122702215.PORTRAIT.jpg?dl=1

PXL_20220914_151458444.MP.jpg?dl=1

PXL_20220916_122743638.PORTRAIT.jpg?dl=1

PXL_20220916_122756427.PORTRAIT.jpg?dl=1

2016-04-12%2021.16.26.jpg?dl=1

PXL_20220916_123127107.PORTRAIT.jpg?dl=1

PXL_20220916_123226889.PORTRAIT.jpg?dl=1

PXL_20220914_140034614.jpg?dl=1

PXL_20220916_123320654.PORTRAIT.jpg?dl=1

PXL_20220914_140415148.MP.jpg?dl=1

PXL_20220914_181100384.MP.jpg?dl=1

PXL_20220916_232715778.MP.jpg?dl=1

PXL_20220916_232557804.MP.jpg?dl=1

PXL_20220916_232848431.MP.jpg?dl=1

 

 

 

 

 

1663372755273.jpg?dl=1

 

 

 

 

 

 

Edited by Cupcake
Added blaster pics and action shot
  • Like 1
Link to comment
Share on other sites

This kit still lives in my living room, and it's still a nicer build than my own, hahaha

 

Still looks great, and still fits amazing.  Should be an easy pass (again)!

;)

  • Like 1
Link to comment
Share on other sites

Hi Christine, 

 

I'm the D.O. making your review. thanks for your Centurion application.

 

In order to continue and add that Centurion Badge under your name, I'll need you to add some missing photos . 

 

Please refer to the updated Centurion Photo Check list bellow.

 

Thank you.

 

 

 

 

Link to comment
Share on other sites

Ok!

Not a problem. Sorry about that. There's a couple checklists floating around this topic so I missed that specific one. 

I'll get to it asap.

Sorry again for the delay. 

  • Like 2
Link to comment
Share on other sites

15 hours ago, Cupcake said:

Ok!

Not a problem. Sorry about that. There's a couple checklists floating around this topic so I missed that specific one. 

I'll get to it asap.

Sorry again for the delay. 

 

Don't worry, we'll be here when you're ready. :salute:

Link to comment
Share on other sites

6 minutes ago, TKSpartan said:

 

Don't worry, we'll be here when you're ready. :salute:

I think it should be all there now!   :jc_doublethumbup:

  • Like 1
Link to comment
Share on other sites

1 minute ago, TKSpartan said:

 

Thank you !,  just need the E11 Blaster photos and we're ready to start.  

I am applying without the blaster. 

Link to comment
Share on other sites

3 minutes ago, Cupcake said:

I am applying without the blaster. 

 

Applying without E11  Blaster is optional only for Basic Approval , for L2 and L3 it's a requirement.   :salute:

Link to comment
Share on other sites

Oh:huh:. That also was not clear in what I was reading. I think the crl threw me off:56pullhair:.   

 

Good news, I do have a blaster, the same one I applied for EIB with. I will add photos later today.  

 

 

  • Like 1
Link to comment
Share on other sites

9 hours ago, Cupcake said:

Good news, I do have a blaster, the same one I applied for EIB with. I will add photos later today.  

 

 

And another last photo we'll need is the Action one.  :salute:

  • Like 1
Link to comment
Share on other sites

Hi Christine, and sorry for delaying.  Life turns a bit crazy from time to time. 

 

We are a few steps to grant your Centurion Badge, but as you may know, Centurion is the top level of accuracy and we check the applicants a bit more detailed and consider not only the Crl but the screen reference images.

 

Bellow are some fixes we need you to do that are Centurion level requirements .

 

 

CRL for Basic: Frown is painted gray and does not leave the teeth area.

 

This is a common issue that can be easily fixed. Carefully using a toothpick with  some paint disolver (non acetone) or sharp tool like a cutter or knife point.

 

9hETh3N.jpg      pEokNsG.jpg       ZjzszRw.jpg

 

Reference Images

 

7kDxvC1.jpg   jK7gume.jpg

 

 

CRL  L3: Ear screws shall be slotted, flat topped, countersunk and painted white.

 

The ears top screws are perfect but the lower ones need to be changed to the flat topped requested in the crl.

 

                                                                                                                                                                  Reference Images

 

NCpyQx7.jpg    fhptchC.jpg        NzFje3J.jpg   p1NuJSw.jpg?1

 

 

 

CRL L2: Correct Aerators/Hovi-MIX tips are present. Screens used shall be of a wide type mesh, with the rim of the mic and the inside white or painted white.

 

This is an easy fix with a few minutes of painting session.

 

                                                                                                                                                               Reference Image

 

xRUrTih.jpg        Mz3LuTW.jpg?2

 

 

 

 

Your small ab plate looks like having a return edge that it's not present in the screen used references. A little trimming time will be needed to solve it. 

 

 

                                                                                                                  Reference Images

      M7urIsX.jpg                                UzU1W3j.jpg?5         wFB6j8I.jpg?1

 

 

 

CRL L3: No return edge on the inside of the front of the forearm is allowed.

 

 There is a remaining little return edge. Just a little sanding job, easy and quick fix.

 

     bPGvx37.jpg    kvSGZpJ.jpg   

 

 

Reference Images

 

DjVHPJ9.jpg

          

 

 

 

CRL L3: Canvas belt must be firm / sturdy in appearance. No creasing or sagging 

 

There are some creases that are quite prominent, a possible solution could be to tighten the canvas a bit and if that doesn't work a replacement will be needed.

In my experience with Anovos canvas belts, I had to carefully remove the ABS belt because the square covers are glued on tightly (if the belt got damaged, I would fix it with an ABS piece behind it) and install a new one. I consider this one the toughest issue but we are confident that you can do it Trooper. We are here to help you if you need. 

 

 

WiinoeU.jpg   AcSyPMG.jpg         eWAN0q8.jpg?1  H0oWKfi.jpg

 

 

CRL L2: Sniper knee plate must be aligned with the ridges on the shin.

 

You did a great advance with the first fix requested in your EIB submission, but sadly, the sniper knee is still a bit lower (red lines) and should go aligned with the shin (blue lines).  To fix that, It would be necessary to take it off and re-glue it  higher to match the ridges correctly.

 

UNe0T7U.jpg   uLfzfHL.jpg              dQjEudb.jpg?1  284c0Z2.png?1

 

Remember you can contact any of us in the DO Dpt. for assistance.  :salute:

  • Like 1
Link to comment
Share on other sites

Awesome armor Christine! The paint on the helmet is done in 2 minutes with a tooth pick, and removing the return edges on the arms is just 2 minutes of sanding so keep up the good work! :jc_doublethumbup:

 

Since you have comments about the sniper knee, I thought I'd share my experience with removing and reattaching it:
I had to remove my sniper knee (didn't get a comment on it but saw the angle was too off), and did so by carefully cutting it away with an exacto knife, with this attatchment:

zip9igf.png

 

It took about 2 hours to just sit with lit candles in the couch and carefully cutting away from myself (almost had my fingers done for a few times near the end when I became impatient)
zQjfnWF.pngpIfLaJc.png

 

When gluing it back on, I had serious issues with what I was trying. I was trying to glue the edges but with the new knee position I had to squeeze it towards the shin too much so the glue didn't have enough surface to grab on to, and because of the awkward position my hands just couldn't squeeze it for long enough for the glue to do its job. Once I scratched my head a little bit my solution (that I wish I had done from the beginning) was just gluing on this part first, and then the other parts
Mpyu1av.png

 

...as it most likely doesnt have any glue on it from before, and there is a lot of nice surface here :peace:

Also don't be afraid of a little gap (we've seen many gaps here in the movie)! QAtlF2c.png

Link to comment
Share on other sites

Thank you for the feedback and advice.

 

I've looked over the list of changes required and they all seem doable. I'm very busy with work right now so it may take a couple of weeks. 

Stay tuned! :popcorn:

 

  • Like 3
Link to comment
Share on other sites

1 hour ago, Cupcake said:

Thank you for the feedback and advice.

 

I've looked over the list of changes required and they all seem doable. I'm very busy with work right now so it may take a couple of weeks. 

Stay tuned! :popcorn:

 

 

Great to know Christine, we'll be ready when you 're ready! :jc_doublethumbup:

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
 Share

×
×
  • Create New...