Jump to content

Mikes ATA STUNT ANH KIT BUILD


TK81B4U
 Share

Recommended Posts

Yesterday was BBB day for me. First thing i did was snap a pic of the boxes on the porch and then i brought them in to open up

and look over the parts and check them out. 

IMG_1868.JPG

Link to comment
Share on other sites

here is the kit after opening the boxes. im sure everyone has already seen an ATA kit but i thought id post it just so that id have it for 

the starting photos of my build thread

 

IMG_1871.JPG.142194af7f073e1b522a0c245e928228.JPG

  • Like 1
Link to comment
Share on other sites

It's always great to see another box opening!!  Congratulations and let's the fun begins :jc_doublethumbup: :happyandcheerfulbirthday:  

 

Feel free to ask whatever question you have. We are here to help.! :salute:

Link to comment
Share on other sites

Nothing better than BBB photos, well there is but I'll not go there ;) 

 

Don't forget the golden rule, measure twice and cut once and in doubt ask or check our gallery sections

 

Good luck and looking forward to seeing your build progress :duim:

Link to comment
Share on other sites

Did some work today on a few parts.  here is some photos of the trimming ive done. Im leaving a bit of return edge on them for now, until i am  ready to start fitting. i would post more but i apparently only have 7kb left of photos that i can post here. i dont know how im going to post more if that is the case.

1549066451_IMG_1921(1).jpg.a789e2255e8a1f031244d8111858ec68.jpg

Edited by TK81B4U
Link to comment
Share on other sites

Forum only allows a certain amount of images per member, with the size of this detachment you could imagine how much data would have to be stored if everyone could post unlimited images.

 

Most of us use an free online photo host, upload your images there then copy the links back to your thread.

 

Here is a great how to

 

Link to comment
Share on other sites

Once you get the hang of using imgur, adding photos will actually be pretty easy.  We suggest posting as many as possible, especially when you have an issue or question as it will make it much easier for us to offer advice.

I have a few tutorials under my avatar below that may help with your build, but always feel free to ask if you have a problem or query before cutting or gluing.  As Glen says:  "There are no silly questions. just silly mistakes".

We are here for ya' every step of the way!

 

Link to comment
Share on other sites

  • 1 month later...

Nice work, you may just want to remove a little paint from the gums, especially for higher level approval ;) 

 

7K32ytA.jpgQjhn4Yu.jpg

s4AllTr.jpg?1

 

 

Add some white on the mic tip rims too :duim:

 biQW7GE.jpg?2   yjHcKIA.jpg?1  

Link to comment
Share on other sites

 

DbsPF2R.jpg  7K32ytA.jpg

                                          (new photo)                                                                                        (old photo)

                     OK I have scraped away some paint from the gum line and cleaned it up a bit, hopefully this looks better.

Edited by TK81B4U
  • Like 1
Link to comment
Share on other sites

6 minutes ago, TK81B4U said:

Here is one more newer photo of the gum line area.

not sure if im taking enough off or not?

 

VVNBF6V.jpg

 

 

Hi Mike, the lower section is perfect. You may want to trim a little bit more on the upper part.

 

                                                                                                                                                              Reference Image 

QaSuvbM.jpg                   7kDxvC1.jpg

 

:salute:

 

 

 

 

 

 

Link to comment
Share on other sites

22 minutes ago, TK81B4U said:

Oh i was hoping that was correct because they are already rivited in place .   whoops!!! is this gonna e a problem ?

Should be attached with screws not rivets ;)  You may scrape through basic approval but it will be mentioned at higher levels

BXBk3H6.jpg   VoclqHR.jpg

L2

  • Clips shall be attached with slotted type, flat or dome top style screws, and be black (two per clip).
    • V head screws are not permitted.

 

 

  • Like 1
Link to comment
Share on other sites

7 minutes ago, gmrhodes13 said:

Should be attached with screws not rivets ;)  You may scrape through basic approval but it will be mentioned at higher levels     "OH BOY" i want to get to atleast level 2 expert infantry

BXBk3H6.jpg   VoclqHR.jpg

 

 

 

Edited by TK81B4U
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
 Share

×
×
  • Create New...