TrooperSam[TK] Posted October 7, 2021 Report Share Posted October 7, 2021 (edited) Armor Maker: RWA Creations Helmet Maker: RWA Creations Blaster Maker: Shear Tech Height/Weight: 184 cm/72 kg Boot Maker: Imperial Boots Hand Guard: RS Prop Masters Sam Edited October 7, 2021 by TK51085 Quote Link to comment Share on other sites More sharing options...
gmrhodes13[Staff] Posted October 7, 2021 Report Share Posted October 7, 2021 If you are having issues adding images most of us use an online free image host, Imgur works well, upload your images there once you have an account then copy the "direct links" directly into your post. 1 Quote Link to comment Share on other sites More sharing options...
TKSpartan[Staff] Posted October 7, 2021 Report Share Posted October 7, 2021 Hi Sam, and thank you for your EIB application. As Glen said, let us know if you're having issues adding images. Once you have added them, we'll proceed with your review. Quote Link to comment Share on other sites More sharing options...
TrooperSam[TK] Posted October 7, 2021 Author Report Share Posted October 7, 2021 Hi guys and thanks for the suggestion, I finally managed to add them 2 Quote Link to comment Share on other sites More sharing options...
TKSpartan[Staff] Posted October 7, 2021 Report Share Posted October 7, 2021 Thank you Sir. Added to the processing line 1 Quote Link to comment Share on other sites More sharing options...
CallMeMrTibbles[501st] Posted October 7, 2021 Report Share Posted October 7, 2021 Ciao Sam, Looking great! Good luck with your application 1 Quote Link to comment Share on other sites More sharing options...
fishgoh0nk[TK] Posted October 8, 2021 Report Share Posted October 8, 2021 Looking slick! Good luck!! 1 Quote Link to comment Share on other sites More sharing options...
Sly11[Admin] Posted October 8, 2021 Report Share Posted October 8, 2021 Looking good Sam. If I may add a suggestion, it would be to tidy up your paint work on the Ab buttons. A little trick to getting rid of those little bits that stick out is to use a toothpick dipped in some mineral turpentine and scratch them away. Easy to do and works well, will give a nicer finish if you can round them off a bit. 1 Quote Link to comment Share on other sites More sharing options...
gmrhodes13[Staff] Posted October 8, 2021 Report Share Posted October 8, 2021 Also couple of photos the DO's like to see. Thigh ammo strip rivets, inside and out. You may also just want to check your TD gaps before the DO's do their review (control panel to end cap gaps) Good luck with approval 1 Quote Link to comment Share on other sites More sharing options...
TKSpartan[Staff] Posted October 8, 2021 Report Share Posted October 8, 2021 Hi Sam, Could you please add the following photos ? Close photo of the Thigh ammo strip rivets, inside . CRL: The rivets used shall be single cap, double cap or split rivets. No pop rivets allowed. Additional photo of your TD from another angle, like example below. Thank you and one of us will be with you shortly. Quote Link to comment Share on other sites More sharing options...
TrooperSam[TK] Posted October 8, 2021 Author Report Share Posted October 8, 2021 Sure, here they are 1 Quote Link to comment Share on other sites More sharing options...
Crampeat[TK] Posted October 8, 2021 Report Share Posted October 8, 2021 Looking good Sam! Best of luck 1 Quote Link to comment Share on other sites More sharing options...
Chemi[Staff] Posted October 15, 2021 Report Share Posted October 15, 2021 Hi Sam, and thank you for your EIB application! CRL and EIB Application Requirements: All required photos have been submitted, and on behalf of the entire D.O. staff we are pleased to welcome you to the rank of Expert Infantry. Congratulations! Other-Armor Fit/Assembly; In this area we review observations made by your fellow troopers and the DO team. Some observations may lead to suggestions to improve the overall look of your armour. Note that we consider both text (CRL) and pictures (screen caps/reference images) when reviewing submissions. Excellent armor Sam, And as I always say, keep in mind that most things are just minor dressing issues. -Well, let's start from the top. This is a very common problem. In a perfect world, the ear screws should go aligned with the rear edge of the Traps(it is mentioned just for your consideration). Reference images -The brow trim is too low(and slightly angled). We are suggesting to rise it up a bit. Your brow trim is sitting lower than ideal for a Stunt TK, and looks more like those worn by Hero TKs. Raising it a bit would give you a much more screen accurate appearance. Stunt reference images Hero reference images -Another very common detail is the next one. The brow trim, should be a bit shorter. The one on the right side is perfect, the left one should be a bit shorter. We recommend you do it little by little so as not to cut too much. Reference images -As seen below, it looks like there is quite a bit of paint on the sides of your right Hovi-tip screen(the left one is perfect!) A few minutes with a razor knife, and fixed!!! Reference images - The paint details on the vocoder could use some definition with a few touch-ups(some non-acetone paint remover, some toothpicks and a few cotton swabs)... Reference images -It looks like you have too much padding on the top of the helmet. For a better overall look should sit a bit lower. This will improve your field of vision as well. Reference images -It looks like your shoulder bridges are too long in the back. You can trim them a little to be more screen accurate. Reference images -Maybe you can raise your biceps a little. It's not that they're misplaced, it's simply to keep them from hitting the edge of the shoulder bells when you extend your arms. -The TD must be centered(a simple dressing issue). Also, it looks like the end of the canvas belt is sticking out a bit. If it's too long, you can trim it a bit (easy fix). Reference images -Button plates should have straight corners, not rounded. Maybe you can sand the edges a little so that the edges are not so rounded. Reference images -We think this rivets are too close to the corner of the ammo belt. This is not affecting you for level 3 but for a more screen accuracy we notice and let you know it for future adjustments. Reference images -The Hengslter counter on the blaster is a bit on an angle compared to screen-used examples. Maybe you can rotate it a little. That would be great! Reference images *************************************************** Centurion Requirements; In this section we prepare you for Centurion. Because Centurion photos show more detail than EIB, items pertaining to Centurion might be seen there and not here and additional photos may be required. We try to point out all that we can from what we see, but the final accuracy is the responsibility of the trooper. -Your tears lines seem to need a bit more black paint in some areas. Just a few seconds with a permanent marker can do the trick. Reference images -Your forearms appear to be too large (should be reduced by about 1.5 to 2 cm at the top for a sleeker look)...We think that you can adjust their size a bit and this will improve your overall look. Reference images Reference image -We think that the look of the buttons needs to be improved. You can use a toothpick with some (NON ACETONE) paint remover. The buttons do not need to be perfect, but we need them to be a little more rounded. I would suggest using a small "Filbert" style (round end) brush. We are sure you will do a great job. Reference images -L3-The top of the ABS ammo belt should sit at or just above the bottom of the central and vertical abdomen button panels. The belt is almost in place. You just need to raise it a little bit. You can put some velcro behind the AB belt, to prevent it from moving. Reference images -Ab plate is overlapping the kidney armor on both sides. As we see that you are a "thin trooper", maybe you can place some foam inside the armor(if needed), and so, align the sides correctly. Maybe it's just a dressing issue, since we see that in some photos, there is no overlapping(in this case, it is enough to be careful when dressing). Reference images -We have several problems with the TD...Don't worry, they are all easy to fix. First of all, raised "buttons" should ideally face toward the rear (Image 1). Also, your end caps appear to be too wide(image 2).It will be necessary to trim them a little. You will need to move the clips outward too. It also appears that the clips are sitting above the control panel(Image 3). Image 1 Image 2 Image 3 To solve all these issues, this is what we would suggest: 1. Remove the clips and trim off the ends (you can use a hacksaw). 2. Trim end caps. 3. Move the clips to where the ends meet the bottom of the control pad and next to the end caps. . 4. Drill holes in the clips for the new screw position. 5. Re-attach the screws. If you have any doubts, you can see the reference images below(or you can contact the DO's team too). Reference images -Your butt plate is riding out and should be brought in to where it aligns with the kidney plate. I would suggest doing a strapping adjustment to get it closer. You can also add a pair of "V tabs" to the end of the plate and this should make the fix. Reference images - The gaps at the bottom of the rear ridges should be filled or backed with a small square of ABS. Very easy fix . Reference images And that's all Sam. We are sure we will see your application for Centurion soon. If you have any questions, you can contact the DO's team, we will be more than happy to help you... Congratulations!!! 2 Quote Link to comment Share on other sites More sharing options...
CallMeMrTibbles[501st] Posted October 15, 2021 Report Share Posted October 15, 2021 (edited) Congratulations Sam!!! Awesome work and awesome armour Looking forward to you Centurion submission Edited October 15, 2021 by CallMeMrTibbles 1 Quote Link to comment Share on other sites More sharing options...
Goggytalks[TK] Posted October 15, 2021 Report Share Posted October 15, 2021 Congratulations Sam on obtaining Expert Infantry status. Well done. Just in case you may feel a little bit put off from the above suggestions to reach Centurion, Don't be, I had to do the same for some of the listed things for your armor . You wont be sorry and your armor will look even more superb than it already does. I had the same issue with my DT as well. I just cut approx 10mm off the white panel and then moved the clips round and re-screwed them back on. I carefully ran a Stanley knife along the finish line and then eased the waste strip off without disturbing the panel from being already glued on. Job done in 10 minutes. Most of all the other things too are easy fixes . Good luck. 4 Quote Link to comment Share on other sites More sharing options...
TKSpartan[Staff] Posted October 15, 2021 Report Share Posted October 15, 2021 Congratulations Sam, welcome to EIB ranks.!!! 2 Quote Link to comment Share on other sites More sharing options...
gmrhodes13[Staff] Posted October 15, 2021 Report Share Posted October 15, 2021 Congratulations trooper and welcome to the EI ranks 3 Quote Link to comment Share on other sites More sharing options...
Crampeat[TK] Posted October 16, 2021 Report Share Posted October 16, 2021 Congratulations Sam and welcome to the ranks! Glad I'm no longer the freshest Expert Infantry member 1 Quote Link to comment Share on other sites More sharing options...
TrooperSam[TK] Posted October 16, 2021 Author Report Share Posted October 16, 2021 Thanks a lot to the DO and to all of you guys I will go through your well detailed suggestions and try to do my best to fullfill them in order to reach the next level! Just a thing about the helmet: I have a very BIG head and a kylo-ren size nose and I assure my top padding is thin, so I'm not quite sure how to pull down my helmet a little more but I'll figure something out. Thanks again Sam 2 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.