Jump to content

MintImperial’s Newbie WTF TK Build


MintImperial

Recommended Posts

Been working to get my armour in decent shape for Halloween,

so I’ve been jumping around getting some parts cosmetically mostly there

then circling back to fine-tune them later.

 

Rushing the greaves, I made a stupid mistake and trimmed too much meat off the left one.

Now it won’t close around my leg (haven’t got around to putting the cover strip on yet,

so it may yet close without a gap, but I don’t want to rely on that).

 

Below, you can see my cut lines and the salvaged armour strips (not quite the right pieces)

that I’ve held in place with masking tape to extend the sides.

 

51628294511_721aa829db_o_d.jpg

 

I’ve used ABS paste to extend the edges.

While it may be messy, and not as strong as the original,

I’m hoping that once I have inner and out cover strips in place, it will all hold together.

 

Measure twice. Cut once. Got burnt. Lesson learnt.

 

Here’s the same piece with ABS paste applied inside:

51628947799_8fca6a2c86_o_d.jpg

 

51628294586_38550ef574_o_d.jpg51627469012_61987e70af_o_d.jpg

 

I’ll leave it overnight and sand it tomorrow.

Doesn’t have to be perfect as the cover strips will sit over it.

 

Edited by MintImperial
  • Like 1
Link to comment
Share on other sites

Also got started on the sniper plate, which, when aligned properly with the top ridges,

doesn’t seem to have many points of contact with the shin itself.

Seems like it’s just a small surface area on each side and the real heavy lifting is done by the front where it sits over the cover strip.

 

To try to improve the strength of the grab, I filled in the sniper plate stud hollows with ABS paste

and I added a tab of spare cover strip material just inside the front to create more surface area contact with the strip on the front of the shin.

 

51628294491_de5ee0694f_o_d.jpg

 

51628515528_60b53171a5_o_d.jpg

 

51629150405_45128b6f4d_o_d.jpg

 

I’m actually worried about having too much rigidity on the sides anyway,

as I need the shins to flex when I open them up and put my legs in.

Hope the sides don’t pop off.

 

 

Edited by MintImperial
Link to comment
Share on other sites

8 minutes ago, MintImperial said:

I’m actually worried about having too much rigidity on the sides anyway,

as I need the shins to flex when I open them up and put my legs in.

Hope the sides don’t pop off.

 

 

Hi James,  the sniper knee looks good, a couple of side photos would be great to check the alignment. And  It's not a common issue the sides to pop up. just be sure to glue the sides and center.  keep up the great work. :jc_doublethumbup:

  • Like 2
Link to comment
Share on other sites

You will find just a small amount of glue on the front and the rear sides is quite enough to hold them 

  • Like 2
Link to comment
Share on other sites

Mine is literally only attached with a small drop of CA glue at the ridges and another on the inside where it touches the cover strip. It's done over 50 troops and is still there for over 7 years now without any problems.

  • Like 2
Link to comment
Share on other sites

I guess your first TK is like your first child.
An overabundance of caution!

Second one will be all slapped together without a care in the world


Sent from my iPhone using Tapatalk

  • Like 2
Link to comment
Share on other sites

15 hours ago, TKSpartan said:

 

Hi James,  the sniper knee looks good, a couple of side photos would be great to check the alignment. And  It's not a common issue the sides to pop up. just be sure to glue the sides and center.  keep up the great work. :jc_doublethumbup:

 

Here are some more shots. Thanks Mario.

 

51630039516_114ca3822b_o_d.jpg

 

51630039491_2beb978fa2_o_d.jpg

 

51630039501_35574f716a_o_d.jpg

 

51629214522_8d2c771767_o_d.jpg

 

 

Link to comment
Share on other sites

2 minutes ago, MintImperial said:

 

Here are some more shots. Thanks Mario.

 

You can see that the top edges of the sniper plate (among many other things) need some clean-up.
I’ll sort that out after Halloween.

Edited by MintImperial
Link to comment
Share on other sites

5 hours ago, MintImperial said:

You can see that the top edges of the sniper plate (among many other things) need some clean-up.
I’ll sort that out after Halloween.

 

It could be my eyes or the photo angle but please check the top  the lower ridges alignment, they look like being a little lower .

 

 

.20orgZQ.jpg?1

 

Gna6m0b.jpg?1

 

3Ay3UcD.jpg?1

 

 

 

:salute:

 

Link to comment
Share on other sites

36 minutes ago, TKSpartan said:

 

It could be my eyes or the photo angle but please check the top  the lower ridges alignment, they look like being a little lower .

 

 

.20orgZQ.jpg?1

 

Gna6m0b.jpg?1

 

3Ay3UcD.jpg?1

 

 

 

:salute:

 

Thanks for drawing that out. Maybe it’s the camera angle.

Right now the plate sits snugly and precisely onto the raised ridges at the top of the greaves.

 

But because one side of the greave slopes downward at the front,

there’s no way to mount it flush to the ridges as required in the CRL

and still have it level from the front.

 

Here’s a different angle showing how each side rests on the ridges:

51631475580_3426d8ed39_o_d.jpg

51629801102_0ab31db7ca_o_d.jpg

 

And here’s how the shin halves match up (left greave is on screen left).

Note the top of the ridges at the front.
I think this may be a quirk of the WTF kit

as other people with it also seemed to have some trouble matching them.

51629807497_a5dfc93e6b_o_d.jpg

 

Here’s the same thing from behind with the sniper plate mounted.

the right side slopes downward, as you pointed out in your image.

51631271889_4f624f903b_o_d.jpg

 

If I mount it so that it’s straight from the front,

it will be too high for the ridge on the right and not meet the CRL.

 

Link to comment
Share on other sites

  • 3 weeks later...
On 10/26/2021 at 10:55 PM, CallMeMrTibbles said:

Everyone will tell you that (as you now know) the sniper knee is a real pain in the derriere!

I will get back to work on that soon.

  • Like 1
Link to comment
Share on other sites

In the meantime, I’ve been making some magnetic tabs to keep my ab & kidney plates from moving relative to each other.

 

I’ve noticed that one or the other often rides up so that their tops are not aligned.

 

One way to fix this would be double snaps on 2” webbing as my build has only 1”.

 

But I thought I’d use the resources I have on hand instead.

 

Using some black ABS this time, I cut out thin strips and, using a heat iron, created an S bend in each.

 

51686192688_76b821f2ed_o_d.jpg

 

Each will hold a magnet on one end that is glued to the other plate.

  • Like 1
Link to comment
Share on other sites

Here’s how they’re looking at the moment.

 

51686603614_b339fd3e05_o_d.jpg

 

51686603644_9811a66b27_o_d.jpg

 

And with some black ABS paste, I made a little cradle for the magnet.

 

51685133107_cbf0d9aa96_o_d.jpg

 

What I like about this particular ABS is the wrinkle texture on one side which,

even if the plates come apart, isn’t too reflective and will blend in much better to my undersuit.

 

Link to comment
Share on other sites

Moving onto my thermal detonator, when I cut the pipe to length, I didn’t have the tools to cut it straight.

 

I’ve corrected this with some putty.

 

51686841450_b1651e829c_o_d.jpg

 

I found that Mr.Color number 13 is a really close match to the Humbrol grey sold by Trooperbay.

 

But now that I’ve sprayed the pipe grey, what should the surface be like?

 

I have a feeling semi-gloss/satin is the way to go.

 

I’ve hit it with some gloss clear coat for now but can take the sheen down later.

 

51685941366_f9df546933_o_d.jpg

Link to comment
Share on other sites

In looking at the screen used ones below, the sheen is minimal (this could be from lots of use, though). ;)  However, the pic on the far right shows that there was a reflection, even if it is only slight.  I think you will be fine with semi-gloss.  Just try to make sure the total width (with caps attached) stays very close to 7 ½ inches (190 mm).

 

VF5c0SA.jpg?1  1z8XJu8.jpg?1  08UR2U4.jpg

  • Like 1
Link to comment
Share on other sites

16 hours ago, justjoseph63 said:

In looking at the screen used ones below, the sheen is minimal (this could be from lots of use, though). ;)  However, the pic on the far right shows that there was a reflection, even if it is only slight.  I think you will be fine with semi-gloss.  Just try to make sure the total width (with caps attached) stays very close to 7 ½ inches (190 mm).

 

VF5c0SA.jpg?1  1z8XJu8.jpg?1  08UR2U4.jpg

Looking at the black scratch marks on the screen-used ones, it seems that these are actually the same one shot under different lighting conditions. The grey looks so different in each.

Edited by MintImperial
Link to comment
Share on other sites

On 10/26/2021 at 10:01 PM, TKSpartan said:

 

It could be my eyes or the photo angle but please check the top  the lower ridges alignment, they look like being a little lower .

 

 

.20orgZQ.jpg?1

 

Gna6m0b.jpg?1

 

3Ay3UcD.jpg?1

 

 

 

:salute:

 

I’m having real troubles lining this up because of the way the shin halves are made.

I can align it with the top ridges, but the right side will always be lower as the right-side ridges are lower.

Or I can straighten it from the front, but the sniper plate will sit higher than the right-side ridge.

 

If I can’t resolve this issue, would it keep me from being approved, and if so, even from level 1?

Edited by MintImperial
typo
Link to comment
Share on other sites

On 11/18/2021 at 7:31 PM, justjoseph63 said:

Looks GREAT, James!  Can you post up a side view?  

Aaaaaaargh!

 

Just dropped something on my TD and scratched the paint as I was about to take a photo!

 

Button plate is not stuck on yet so I’m holding it in place.

51703898596_f4a2031413_o_d.jpg

 

Brackets are positioned so that the TD sits above the top of the canvas belt.

51703898601_e54422bb7f_o_d.jpg

 

Link to comment
Share on other sites

14 minutes ago, MintImperial said:

Aaaaaaargh!

 

Just dropped something on my TD and scratched the paint as I was about to take a photo!

Battle damage.... not to worry.

 

Button plate is not stuck on yet so I’m holding it in place. 

Brackets are positioned so that the TD sits above the top of the canvas belt.

Can you post up some pics?

 

  • Like 1
Link to comment
Share on other sites

Should be able to just touch up those areas of paint.

 

Just make sure when you have it on your belt that you can see the O detail, many miss then when assembling ;) 

 

References below

 

 66W22Oe.jpg?1   ENBGgGW.jpg?1 

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...