Jump to content

Rubies E-11 1st-Timer Build


Joey 1-Time

Recommended Posts

Whats up everyone!

 

Long time, first time.  This is my build thread for modifying the Rubies E11 toy.  This build is fairly dremel intensive, and I used a bit of 3D printing.  

 

lKlgjkZ.jpeg

 

I know its not going to be a super accurate screen build, due to the nature of the base toy. But I'm hoping to make something that looks really good while trooping.  

 

I just want to give a quick shout out to all the people on this forum for all the amazing information and advice on how to go about this process.  I was a complete noob when I started (and still am by most accounts), but gathered enough tips to allow me to attempt this. If anyone has any questions, I would be happy to share my limited experience. 

 

Materials:

Rubies E-11 Blaster

PVC pipe (3/4')

Flat Gray Primer Spray Paint

Matte Black Spray Paint

Matte Clear Spray Paint

Gun Metal Acrylic Paint

Metallic Silver "Testors" Paint

Metallic Copper "Testors" Paint

 

Tools:

Dremel

Sandpaper

Xacto knife

Painters Tape

Paint Brush

 

p1ZZPPG.jpg

 

I'm not sure about painting this though. I know I'm getting a bit ahead of myself, but I want to get the materials early so they have time to ship.  I know it has to be painted black, but what finish should I use? Matte?  Also, does anyone have any recommendations for a sealant, since I don't want the paint to run? Any advice or links would be greatly appreciated.

Edited by Joey 1-Time
  • Like 2
Link to comment
Share on other sites

Hello Joey and welcome to the FISD.

 

When it comes to painting, you can use flat black spray paint for the main parts and gloss black only for the handle.

This thread might also be of help.If you run into questions or problems, just ask.

Link to comment
Share on other sites

First, i took some 200 grit sandpaper and sanded off the text that was on the side of the gun.

 

knOx8UJ.jpeg

 

Then, I started with the holes on the barrel. The dremel I bought came with a bunch of bits, and one of them fit the size of the premade holes perfectly.  So I just drilled straight into the barrel with it and it worked perfectly. I cut out all of the premade indents.  I plan on putting an inner barrel in there eventually, but more on that later.

 

KeHqrNB.jpg

 

3T9GNnP.jpg

 

Next, I cut out the sights.  I used a smaller bit and carefully cut out the sights for a more accurate look. I'm starting to like how these small modifications are going to make a big difference.

 

ICRC8t0.jpg

 

H0z2UWJ.jpg

  • Like 2
Link to comment
Share on other sites

I started to work on the rail, trying the remove the plastic underneath so the rail would sit above the barrel.  I found it really tough, and I was struggling. 

 

LKwcAHr.jpg

 

I thought that if I opened the gun,  it would be easier to get to.   I read a tip on another thread about freezing it in order to help open it (dont remember who it was).  So, I put the gun in the freezer for about 24 hours. When I took it out, I got a butter knife and stuck in in the seal and started to pry it open. 

 

sJf1FB6.jpg

 

The freezing weakened the bond of the glue, which allowed it to open easier.  I still thought i was going to crack it a few times, but I managed to get it open undamaged.  With the rail more exposed, I was now able to finish it up.

 

kIejWnz.jpg

 

 

 

OGDG5Gq.jpg

 

The saw bit really came in handy for this.

 

K0SBI1C.jpg

Link to comment
Share on other sites

12 hours ago, SeanTX said:

I spray painted mine silver then used the rock salt chipping method then black with a light dusting of dark grey on top. Easy afternoon project and looks great enough for the money spent.

I might have to try that.  Did you use any sealant or anything?

 

4 hours ago, gmrhodes13 said:

Coming along nicely

Thank you, I'm happy with it so far

  • Like 1
Link to comment
Share on other sites

Next up, I cut out the bottom of the scope for more accuracy.

 

DtiCx74.jpg

 

 

IWpVzLM.jpg

 

This part is what I would consider the most necessary modification: cutting down the T-tracks.  I'm very happy with the end result; makes it look a lot less cartoon-ish. I still need to do some sanding and evening out, but I'll get around to it.

 

OgSsyWb.jpg

 

rlMXBru.jpg

 

 I am waiting until I put both sides back together before I do the top track, just to make it easier to line up perfectly.

 

 

 

 

Edited by Joey 1-Time
  • Like 1
Link to comment
Share on other sites

On 9/8/2020 at 7:51 PM, Joey 1-Time said:

Next up, I cut out the bottom of the scope for more accuracy.

 

DtiCx74.jpg

 

 

IWpVzLM.jpg

 

This part is what I would consider the most necessary modification: cutting down the T-tracks.  I'm very happy with the end result; makes it look a lot less cartoon-ish. I still need to do some sanding and evening out, but I'll get around to it.

 

OgSsyWb.jpg

 

rlMXBru.jpg

 

 I am waiting until I put both sides back together before I do the top track, just to make it easier to line up perfectly.

 

 

 

 

 

Those T-Tracks look great!

  • Like 1
Link to comment
Share on other sites

Next up is the inner barrel. I bought some 3/4' PVC pipe to use for the barrel.  I measured how long it needed to be and cut to size, and then drilled holes in it to fit. 

 

698cmzd.jpg

 

I ended up spray painting the barrel and inside as a test to see how the paint would look.  I used matte black and I'm pretty happy with the result.  Once I had the pipe lined up, i used a generous amount of E-6000, which held very well.

 

EOpD4IQ.jpg

 

Rkt1f25.jpg

  • Like 1
Link to comment
Share on other sites

  • 8 months later...

Soooooo... I put the project on hold for a while, but I'm working on it again and not stopping until it's done this time!

 

Next thing I did was cut out the bolt/spring slot (not sure what it's called exactly).  I started off drawing a template with pencil after looking at many reference photos. I had to redraw it a couple times, but it looked good enough in the end.

 

qVaCK3T.jpg

 

Next, I used my trusty Dremel to cut out the shape by using the saw bit and the cylinder bit.

 

wDseA0l.jpg

 

I didn't end up putting in a spring in the receiver, as to me it was too much work for not a huge effect. I instead out the rest of the pvc pipe that I used on the barrel and glued it the same way.

 

Ghg0uGn.jpg

 

9YQGpmQ.jpg

 

I didnt like how the D-ring mold looked at the end of the gun, so I 3d printed a better one.  I dremel'd off the one that was there originally

 

dXiE6dC.jpg

 

T7o04f7.jpg

 

 

Link to comment
Share on other sites

  • 2 weeks later...

Finally, it was time to put the gun back together. I screwed back in all the screws that I look out previously.  I then flattened out the top T-track to match the others, then I trimmed down the trigger guard

 

klJ4HgD.jpg

 

This next part was definitely the most time consuming part of the whole project.  I first had to sand down the entire gun (for better paint adhesion), but specifically the line where the two halves of the gun meet.  There is a slight bump there that I wanted to get rid of.  I then used bondo putty along the entire gun to cover up the seal of the two halves.  This was especially necessary under the rail, scope, along the middle t-track, and the trigger guard; which is due to small gaps that were created during trimming.  Also, I filled in all the screw holes.  It took several coats and smoothing out with sand paper before I got it just right

 

ZeVf9YS.jpg

 

5LNCFIV.jpg

 

With E6000 I glued on the two parts I 3D printed:  The power cylinders and the D-ring

 

herrBHC.jpg

 

TAXtFnX.jpg

 

 

 

  • Like 1
Link to comment
Share on other sites

On to the painting.  I used a primer first, making sure to get in all the small crevices and small bits.  I did a couple coats to ensure it was completely primed.

 

lBoEuF5.jpg

 

Next, came the black.  I used a matte black spray for the entire thing.  The grip should have been gloss, but it's not going to be seen much and I was being cheap lol. 

 

It's finally starting to look like the real deal. 

 

AB8ZoTY.jpg

  • Like 2
Link to comment
Share on other sites

And then, it was painting time.  I started with the bolt.  I taped off the general shape, using the edges that were already molded on the gun as a guide.

 

Then, I painted the area using the gun metal acrylic paint (with help from the Mrs. lol).  I rounded out the bottom left corner to match how it should look.  It came out pretty well

 

AwBkSpo.jpg

 

IIgM8S6.jpg

(I forgot to take an after picture, so this one was done post weathering)

 

Next comes the weathering.  I used a dry brush method, which basically consists of dipping the brush in paint, then getting almost all of the paint off the brush, then very lightly brushing the edges and corners of the gun to get a natural looking weathered effect. There are guides online to look up how to do this properly, which is what I did. I started using the metallic silver paint to do everything but the scope, t-tracks, and grip. The t-tracks and grip are not supposed to be metal, so they would have no metal weathering.  The scope is covered below.

 

vAAhq4Y.jpg

 

3yyIp7A.jpg

 

5DZ8CFa.jpg

 

I did the same method for the scope, but instead I used metallic copper, since the original guns scopes were made of brass.  I went more subtle on the scope, as I felt like i went a little overboard on the silver.  It was looking so good I got carried away a bit.  If I had to do it again I may have done a little less, but I still like how it came out.

 

EYcwcAU.jpg

 

The only thing left to do was to coat it with the matte clear to protect the paint.  And that's it, finally done!

 

yXjtwGT.jpg

 

I'm very happy with how everything turned out.  I know I could have done more to be more accurate, but I didn't want this build to take too much time.  I plan on doing another, more accurate build in the future, but I'm very satisfied with this gun until then.  From afar, it looks great.

 

If anyone has any questions on how I did anything, just ask.

Edited by Joey 1-Time
  • Like 1
Link to comment
Share on other sites

On 6/22/2021 at 8:26 PM, Joey 1-Time said:

And then, it was painting time.  I started with the bolt.  I taped off the general shape, using the edges that were already molded on the gun as a guide.

 

Then, I painted the area using the gun metal acrylic paint (with help from the Mrs. lol).  I rounded out the bottom left corner to match how it should look.  It came out pretty well

 

AwBkSpo.jpg

 

IIgM8S6.jpg

(I forgot to take an after picture, so this one was done post weathering)

 

Next comes the weathering.  I used a dry brush method, which basically consists of dipping the brush in paint, then getting almost all of the paint off the brush, then very lightly brushing the edges and corners of the gun to get a natural looking weathered effect. There are guides online to look up how to do this properly, which is what I did. I started using the metallic silver paint to do everything but the scope, t-tracks, and grip. The t-tracks and grip are not supposed to be metal, so they would have no metal weathering.  The scope is covered below.

 

vAAhq4Y.jpg

 

3yyIp7A.jpg

 

5DZ8CFa.jpg

 

I did the same method for the scope, but instead I used metallic copper, since the original guns scopes were made of brass.  I went more subtle on the scope, as I felt like i went a little overboard on the silver.  It was looking so good I got carried away a bit.  If I had to do it again I may have done a little less, but I still like how it came out.

 

EYcwcAU.jpg

 

The only thing left to do was to coat it with the matte clear to protect the paint.  And that's it, finally done!

 

yXjtwGT.jpg

 

I'm very happy with how everything turned out.  I know I could have done more to be more accurate, but I didn't want this build to take too much time.  I plan on doing another, more accurate build in the future, but I'm very satisfied with this gun until then.  From afar, it looks great.

 

If anyone has any questions on how I did anything, just ask.

 

Looks amazing man!

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...