Jump to content

TK-22418 Requesting ANH Stunt Centurion Status [RS Props] (Inactive)


WodiQuix
 Share

Recommended Posts

Hello FISD team! For your consideration, here is my (hopefully) Centurion-ready ANH stunt TK! This armor has gone through a heck of a lot of changes, and I couldn't be more proud of how far I've come with it. 

 

Name: Ian Malinoski 

Forum Name: WodiQuix 

Legion ID: 22418 

 

Armor Maker: RS Props 

Helmet Maker: RS Props 

Blaster Maker: DoopyDoos 

Boots Maker: ImperialBoots 

Canvas Belt Maker: Imperial Issue 

Hand Plate Type: White Latex 

Electronics: iComm and Aker Amp/microphone 

Neck Seal Maker: Geeky Pink 

Holster Maker: TrooperBay 

 

EIB Thread:  

 

 

ytyLUKg.jpg

 

WZnZ9Zq.jpg

 

rycBVo0.jpg

 

AuNZA9S.jpg

 

KwJ1dM6.jpg

 

V5FkD6Z.jpg

 

gM8Vgp1.jpg

 

wQe1qhL.jpg

 

Q9AYeJg.jpg

 

zOf6oTo.jpg

 

sBoPAqp.jpg

 

36A1hOn.jpg

 

hN9BD7o.jpg

 

2SPnYUo.jpg

 

G2LAqA6.jpg

 

N76cMy1.jpg

 

RnxgcgD.jpg

 

xlZtCT9.jpg

 

IcG3JWh.jpg

 

REfsWFc.jpg

 

v383s4Z.jpg

 

dOhVnTS.jpg

 

tlO5GZ9.jpg

 

QXJmFVF.jpg

 

TowarTX.jpg

 

Nx7aa6q.jpg

 

SMv13Ql.jpg

 

pFdSjPY.jpg

 

4unKeqc.jpg

 

GhmNzXr.jpg

 

SXTIfnv.jpg

 

4S5oT3q.jpg

 

wC3R6uA.jpg

 

dQGfzWh.jpg

 

Thank you again for your consideration! I'm looking forward to hearing from the experts. :)

Link to comment
Share on other sites

After looking over a number of other Centurion applications, I decided to raise my brow trim to become a high brow-er! I think it looks pretty cool! I had always liked the low brow look, but the high brow look slowly grew on me.

 

vaZkVri.jpg

  • Like 1
Link to comment
Share on other sites

  • 2 weeks later...

Nice work could you also post up some updated close up images please

 

Sniper plate both sides

Thigh ammo strip rivet

Butt plate snaps

Ab plates

Helmet sides and vocoder

Ab plate side top snap

Ab plate side rivets

Belt

 

Link to comment
Share on other sites

  • 2 weeks later...

Hi Ian, and sorry for the delay.  Again, after going over the following items with fellow staff members we have to hold off on your submission for the time being, sad to say.

As I mentioned, several of these items were fine in your EI request, but after changing out many of the components they no longer meet the requirements for Centurion level, which is all about the small details.  We sincerely hope you can remedy these issues and re-submit soon, and if you require any clarification or need any help, just ask!

 

The base of your helmet has quite a large divot as seen below the rear of the right ear.  This can be effectively covered by moving the base of the ear backward, (photo 3 shows another RS helmet to give you an example).  Doing this would also move them into a more screen accurate position.  Many of the screen used buckets were a little wonky in certain places, but we can find no references showing any with such a large recessed area.

 

                                                                                              Photo 3                                    Reference images (Note how screws line up with rear trap angle)

L2zDT2c.jpg    ThtTcUi.jpg            bA58wAD.jpg?2                         IQOqnU6.jpg?1   MN894UQ.jpg?1

 

The "Han" snap will need to be moved farther out toward the edge as seen in the reference images.  We are also highly suggesting that you eliminate the overlap of the ab-plate on the right side.

                                                                                                 Reference images

OacdhVX.jpg         6t6Lgj6.jpg?1  NooJ6ya.jpg?1  Hl01ncc.jpg

 

As stated in the CRL, ".. the corners of the plastic ammo belt shall be trimmed at a 45 degree angle that meets the outer edge of the cloth belt".  There are 2 ways to go about fixing this..

1.  Get a cloth belt that is a bit narrower, or

2.  Get a new ABS belt and leave it a bit wider when trimming in order to get the correct size on the angles (photo 2).

 

                                               Photo 2                                                                                  Reference images

SWGEZMG.jpg     CGy2ZOY.jpg                 9u4dsca.jpg  gdK7MSg.jpg  aUWkDIk.jpg

 

Your shoulder bells will need to adjusted to where the tops are touching (or very close) to the shoulder bridges as seen in your EI submission (photo 2).

 

                                                                                           Photo 2

YSaIYfd.jpg   95RDO07.jpg   

 

Below is one more suggestion:

 

Your sniper knee tops could use some trimming to give them more of an angle.  EASY fix!

 

                                                                                                  Reference images

URT9s3H.jpg        nlEfhJP.jpg?1   4qD0eo1.jpg?1   I43rojW.jpg?1

Link to comment
Share on other sites

  • 6 months later...

This is now considered an inactive thread.  Please contact any member of the D.O. staff to continue the review process

Link to comment
Share on other sites

  • gmrhodes13 changed the title to TK-22418 Requesting ANH Stunt Centurion Status [RS Props] (Inactive)

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
 Share

×
×
  • Create New...