Jump to content

Starkill20's TLJ FOTK KB Props Build


Starkill20

Recommended Posts

1 minute ago, Krisko720 said:

Just so you know.. because I made the mistake.. the line I circled in your pic is not a trim line. It’s where the spat sits on the shin. It’s misleading because it looks like every other trim line. I’m waiting on another set of shins because of this. Just wanted to save you from a potential bad cut! Lol

3ad2313dbf1ef35b287ad3c5a2a57c9a.jpg


Sent from my iPhone using Tapatalk

Thanks for the heads up! I remembering reading something about that but I thought it was meaning something on the spats themselves! I really appreciate the advice! This is why I am going through and posting all of these pre-trimmming pictures!

  • Like 1
Link to comment
Share on other sites

Next are pictures of the back plate. This seem pretty straight forward. I might have issues with sizing the amount on the arm areas but I'm sure I'll be able to figure it out.

 

Face view of the back plate.

49818566582_7ba2b48b0a_z.jpg

 

Detailed view of the flash to be trimmed off.

49818253861_bd5646856f_z.jpg

 

Level left side view of the back plate.

49818254566_9f81e2d446_z.jpg

 

Level top view of the plate.

49817719393_a597a97c4e_z.jpg

 

Level right view of the plate.

49818255676_a2da7e2b51_z.jpg

 

Level bottom view of the plate. Looks like it doesn't need much trimming except for a couple of spots.

49817720683_a2e3dc2646_z.jpg

Edited by Starkill20
Link to comment
Share on other sites

Here are pictures of the front plate. Once again not much to trim it seems, just sizing the arm holes down to an appropriate size.

 

Face view of the plate.

49818256956_a5cc95df62_z.jpg

 

Bottom view of the plate. Any know how much of the edge should be taken off?

49818570692_924f472149_z.jpg

 

Left side flash to be trimmed off.

49818571277_611a92da13_z.jpg

 

Level left side of the plate.

49817722648_b3944b6f22_z.jpg

 

Level top view of the plate.

49818259396_d0aa70daf8_z.jpg

 

Level right view of the plate. Sorry about the quality of this photo.

49818572612_fa407530a9_z.jpg

Link to comment
Share on other sites

Next is the yoke plate. Once again fairly obvious where I nee to trim. Like the the back plate, and the front chest plate I may need some advice on where to trim the arm holes. And I don't have it traced in the pictures but I did find the very slight trim line where it is supposed to be cut to so it can fit cleanly to the back plate.

 

Face view of the yoke plate.

49818260156_c3cbdd6be5_z.jpg

 

Level left side of the yoke.

49818573687_fe5fa84012_z.jpg

 

Level top side of the yoke.

49818261191_8b752a448e_z.jpg

 

Level right side of the yoke.

49818574827_cf577e710a_z.jpg

 

Level bottom side of the yoke.

49817726433_447c711da1_z.jpg

Link to comment
Share on other sites

And finally picture of the accessories and stickers. I realized they aren't in this picture but I do have the two trapezoid shaped greeblies for the left shin. Right now I'm looking at getting the clips from R2Dan. And some of the stickers look useful but I haven't decided if I will be using them for some of the pill shaped slots. If anyone has any suggestions on what could be done instead of stickers please let me know!

 

49818576197_718c03a54a_z.jpg

 

49818577017_fc30e83158_z.jpg

 

I know it was a lot of pictures to upload but I figured these could be helpful for future kit builders. It also gives all of you a chance to assist me before I make a wrong cut! Next step is trimming!

  • Like 3
Link to comment
Share on other sites

  • 3 weeks later...
On ‎4‎/‎26‎/‎2020 at 6:27 AM, joshuasme said:

Ordered my KB kit 2 weeks ago, can't wait to get started

Hey Josh do you have a build thread started yet?

Link to comment
Share on other sites

The backs of the belt boxes are curved because they will sit against the belt and contour to the curve of your waist better when you wear it.

Edited by Anzo
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...