Jump to content
Rat

ANH Stunt commission build (Anovos)

Recommended Posts

So this is a great honor and privilege a future garrison mate has entrusted me with. I'm up for it though there will be some modification needed. Anyone with tips on resizing the kidney, back and chest would be handy. This is mostly because I'm not sure of methods to do so. She is also a bit on the thinner side at roughly 5'7" and 150 pounds. So I've already gotten her roughly fitted and know those areas will need to be addressed. I'll reach out for some info on higher levels and what is acceptable as I go as well. She may never apply for anything more than basic, but I'll do my best to build to Centurion.

 

So off we go to interesting territory.8268b8565da2240c888d667d41eef384.jpg

 

Sent from my VK815 using Tapatalk

 

 

Share this post


Link to post
Share on other sites

Hey Rat this armor isn't much different than RS. Here's an RS build thread for smaller troopers 

 

  • Like 1

Share this post


Link to post
Share on other sites
Hey Rat this armor isn't much different than RS. Here's an RS build thread for smaller troopers 
 
Thanks Tony.

Sent from my VK815 using Tapatalk

Share this post


Link to post
Share on other sites

Good for you, Rat. I’m sure you’ll do a great job. :-)

Share this post


Link to post
Share on other sites
Good for you, Rat. I’m sure you’ll do a great job. :-)
Thanks Daniel.

Sent from my VK815 using Tapatalk

Share this post


Link to post
Share on other sites
Hey Rat this armor isn't much different than RS. Here's an RS build thread for smaller troopers 
 
I remember following Dianes build, but when I went to review it many of her photos are blurry for some reason. May be something on my end so I'll try again.

Most of the nodding I have to make are in width not so much in height.

Sent from my VK815 using Tapatalk

Share this post


Link to post
Share on other sites

So the standard sizing is about complete. Now to move forward on marking out the modifications that will be needed. I'll shorten the shoulder tabs and trim some off the bottom of the chest. I will also be separating the cod to shorten it as well. The kidney I will just reshape a bit and use foam to make up any extra space. The back and butt plate will be left as is for now. Then of course some heat shaping is gonna happen on the forearms and thighs. I'll be using TrooperMasters suggestions for the thigh trimming as well.667aba890d56dc132eafd417a3a6a2f9.jpg2b024a67ab4598a77530e4c11683b8fe.jpg725ba35a06a4d6a541b2fb799fc41df6.jpgcbfe5a2ba34635e16c2dc1840bd5c836.jpgde3218c8bd0bb63563145494b0e2dd7d.jpg59c0f299dcd065e95dac54417e3f0986.jpg77e8f6e3bcba09a9d993b43df7238c50.jpg

Sent from my VK815 using Tapatalk

Share this post


Link to post
Share on other sites

So I've started gluing the basic stuff like the biceps and forearms. Now time to let the E-6000 to cure and I can put in some work on the magma kit.

Fki85Jv.jpg

 

Also had a bit of a freak accident with my belt sander where one of the forearms got pulled and wedged between the belt and wheel. So paste and sanding to fix that and a spot of paint and you'll never know it happened.

XbqCweg.jpg

Share this post


Link to post
Share on other sites

So big jump forward. All done and delivered. I'm mostly happy with it but it bugs me that the kidney and ab on the right side seems out of alignment. But I wasn't there for this. The only complaint she has is that she wants to add straps to the forearm to bicep, as we initial wanted to go with foam.243b386456a887e0a69b2ed8786bd458.jpg

Sent from my VK815 using Tapatalk

Share this post


Link to post
Share on other sites

WOW... awesome job on this build, sir!  :jc_doublethumbup:  You are right, that kidney/ab connection would drive me nuts, lol.  It looks to still have it's return edge, so could definitely stand for some trimming.  Also noticed that the ABS belt could be centered a bit more if possible.  The button ideally should be centered above the center cod ridge.  Adding straps to the forearm/bicep would not only keep them from riding down, but would also help keep them from twisting.  Looking forward to seeing your next commission! :popcorn:

 

7Ott2C6.jpg       ELoqIL8.jpg?1 C3KCW1p.jpg?1 

  • Like 1

Share this post


Link to post
Share on other sites
WOW... awesome job on this build, sir!  :jc_doublethumbup:  You are right, that kidney/ab connection would drive me nuts, lol.  It looks to still have it's return edge, so could definitely stand for some trimming.  Also noticed that the ABS belt could be centered a bit more if possible.  The button ideally should be centered above the center cod ridge.  Adding straps to the forearm/bicep would not only keep them from riding down, but would also help keep them from twisting.  Looking forward to seeing your next commission! :popcorn:
 
7Ott2C6.jpg&key=1272b07d297aa117c97d493966ed95c4e4d3bbc1e252e280c42ba03bc9b0646c       ELoqIL8.jpg?1&key=3c39190c734d64e3da5231ecca7cea5699af26ff0eca0745843810047b2eea7c C3KCW1p.jpg?1&key=31eacf94a1b40aa7d57d0f7b0c5f4a5d341056ff74a9b257c328a0b3ab180afd 
Thanks Joseph the cod was separated as she is a little short for a trooper, but I did line it up with the original groove. It may just be The angle of the photo. The foam was her choice and has decided she doesn't like it. That ab and kidney connection I think can be solved by adding a bit of foam to fill out the space a little.6462f0915e3b509fdd0608c1992ff39c.jpg

Sent from my VK815 using Tapatalk

Share this post


Link to post
Share on other sites

Actually it just dawned on me she may not have attached the belt.

Sent from my VK815 using Tapatalk

Share this post


Link to post
Share on other sites

Very nice work, well done

  • Like 1

Share this post


Link to post
Share on other sites
Very nice work, well done
Thanks Glen.

Sent from my 5054N using Tapatalk

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

×
×
  • Create New...