hazamel[TK] Posted September 6, 2019 Report Share Posted September 6, 2019 Hi, I'm requesting EIB status for my ANH Stunt. My name is Florian Stratil and I am a member of the German Garrison. Build-Thread: Mandatory Information Armor = RS Prop Masters Helmet= RS Prop Masters (Commission) Blaster= Imperial Warfighters (Rubber-Version) Optional Information Height = 1,83 m Weight = 89 kg / 196lbs Boots = Imperial Boots Canvas belt = RS Prop Masters Hand Plates = Latex RS Prop Masters Electronics= None Neck Seal = RS Prop Masters Holster = RS Prop Masters Quote Link to comment Share on other sites More sharing options...
gmrhodes13[Staff] Posted September 6, 2019 Report Share Posted September 6, 2019 Nice work trooper a few images the DO's like to see are: * Front and both sides of the knee sniper plate * Thigh ammo strip rivets outside and inside * TD showing front panel * D ring on rear of blaster * Closeup of shoulder straps (front and back) * Closeup of your hand plates * Closeup of belt * Closeup of boots A couple of things which you may want to address before the DO's see your application and these are observations not requirements: Your belt is very frayed, although you can have some fraying it is a lot and you may be asked to change it but you can wait to hear what the DO's say. Also ab is overlapping kidney plate. TD not clipped in properly Butt plate hanging or being pushed downwards perhaps tighter strapping Normally stunt helmets the brow is a little higher and Hero version lower, but again wait to hear what the DO's say Your thighs need to come up, you have a big gap between them and the cod Watch the ab and kidney plate alignment at the tops as they are stepped here Your shoulder bells appear to be sitting under the chest plate, you may want to try bringing the shoulder bells inward at the top to the shoulder straps, this may change the angle of them or you may need to trim them on an angle so they sit better. Also biceps are not quite level. There is a section on the top lip of the kidney plate pulling or sticking up, also your right calf does not appear to be central or closed properly. Again you can see the shoulder bells behind the back plate. You could trim a little of the ends of the brow trim, most references stop just before the ear Blaster appears bent? A few tweaks and you'll look great, good luck with approval 1 Quote Link to comment Share on other sites More sharing options...
TKSpartan[Staff] Posted September 6, 2019 Report Share Posted September 6, 2019 Hi Florian, Glad to see another trooper going to higher levels. Looking good, just few adjustment and add the photos Q has recommended and you'll be ready to go EIB and Beyond !! cheers Quote Link to comment Share on other sites More sharing options...
msouza[TK] Posted September 9, 2019 Report Share Posted September 9, 2019 Hello Florian, Looks like you've gotten some great advise from your fellow troopers. Please upload the following photos, Once I get these we can continue. * Front and both sides of the knee sniper plate * Thigh ammo strip rivets outside and inside * TD showing front panel * D ring on rear of blaster * Closeup of shoulder straps (front and back) * Closeup of your ab buttons * Closeup of your hand plates * Closeup of belt * Closeup of boots 2 Quote Link to comment Share on other sites More sharing options...
hazamel[TK] Posted September 9, 2019 Author Report Share Posted September 9, 2019 (edited) First of all: Thank you for your Feedback. We focused on certain points and missed other ones. The mandatory pictures: Sniper Plate Thigh ammo rivets inside and outside TD Front Panel D-Ring Shoulder Straps Ab-Buttons and Hand-Plates (Hope this counts as one...) Belt Boots Now on to the stuff @gmrhodes13 already mentioned: Helmet I pushed the rubber a little upwards (veeeeeeery gently) and it's like this now. Maybe it was the perspective with the other pictures. Will also do the trimming of the rubber as you recommended. E-11 I don't know what it is with this blaster. As long as I have it right in front of me it looks perfectly straight. As soon as I took the pictures it mostly looks like I'm carrying around a banana. Right side I'm working on finding the sweetspot between too loose and too thight. I guess with "hanging butt" your talking about the buttplate sticking out like a duck's butt? I'll try tighter strapping but I was afraid ripping out the bracktes sooner than later. Calves Aligend nicely. The left one is closed in the middle. Don't know why the whole is showing. I'm maxing out the RS ones pretty much. Shoulder bells They are indeed my archenemy! They can look like this or like this I guess that's based on daily motivation and placement of the biceps. Back looks like this Thighs Hope the height of the thighs is better in the second picture. They don't get any higher. I'm stuck with my real thighs in the middle of the plastic ones. Already tried a lot of adjustement while building. As a result I always had a lot of room at the ends and was stuck in the middle. Guess it's too much running to keep my midsection slim enough to fit into the torso. Belt Belt is a bit of a disappointment. Looked fine when I got it, but as soon as I stored it while building the velcro started pulling strings from the front layer. Have to say I'm a little disappointed from the quality RS delivered. I already tried to fix the ends with glue and clear coat to prevent any further ripping. As you can see in the pictures it was only a small success. I hope I covered everything so far. Edited September 9, 2019 by hazamel Changed and added picture 2 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.