Jump to content

ANH TK Stunt Build (AP w/Trimmed Helmet)


Lumpy

Recommended Posts

Hey All!

 

Figured I would start my build thread. I'm still waiting on my kit but wanted to set this up for when I get going. 

 

Armor : Authentic Props Received -  07/17/19

Soft Hand Guards : Authentic Props Received -  07/17/19

TD Clips : Authentic Props Received -  07/17/19

Holster : Authentic Props Received -  07/17/19

Gloves : Authentic Props  Received -  07/17/19

Canvas Belt : Authentic Props  Received -  07/17/19

 

 

S-Trim : Trooperbay - Order Pending

 

 

Neck Seal : Geeky Pink's - Received

Undersuit : Ebay - Recieved

Boots : Funtasma Size 14D (Amazon) - Received

Hardware: Stormtrooper Bracket Set (MrNoStripes) - Received

E-11 Blaster : DoopyDoo - Received, 50% Complete, Ongoing

Fans: Ebay - Received, Built /Functioning 100%

Comms: Troopduino  - Received - Built/Functioning 100%

 

Supplies 

Humbrol Paints #5, 14, 85 - Received

ABS Scissors - Received

E-6000 Glue - Received

Magnets - Received (Probably not enough)

 

I've scaled back my touring with R2 this year and hope to have this project complete by fall. I'm back to reading

build threads and taking notes of tips/tricks. I also have a few local 501st folks to help me along.

 

Wish me luck!

 

Kris aka Lumpy

 

 

 

Edited by Lumpy
Updating - Status
  • Like 1
Link to comment
Share on other sites

8 minutes ago, Bud Spaklur said:


Wook- you should hook this Badlander up with some Maple Moose Eisley action! Once he completes his build, of course!


Sent from my iPhone using Tapatalk

Okay Kris, in the interest of the March to 1000 - a free moose patch when EIB is achieved. :smiley-sw013:

Link to comment
Share on other sites

Neck seal came in today... I've been wearing it around the house just because.... lol

 

Looking for tips/trick for any tools/supplies that may help my build go smoother once my armor arrives... I am browsing the posted lists as well.

 

Cheers!

  • Like 1
Link to comment
Share on other sites

3 hours ago, Lumpy said:

Neck seal came in today... I've been wearing it around the house just because.... lol

 

Looking for tips/trick for any tools/supplies that may help my build go smoother once my armor arrives... I am browsing the posted lists as well.

 

Cheers!

Definitely a fashion statement ;) 

 

Here is a supply list which may be of help 

Link to comment
Share on other sites

Great news, get some research done in the meantime and don’t forget to use references in the gallery section. Looking forward to seeing those BBB photos

Link to comment
Share on other sites

  • 2 weeks later...

BBB Day!!!!!

 

Arrived a week early too!

 

Myself, Ben and Luke had to try on the helmet!!!!

 

So excited!!!!

 

Now my biggest fear... building it! Be prepared for stupid questions

i'm sure y'all have answered a hundred of times!

 

Kris

20190717_094402_resize.jpg

20190717_164107_resize.jpg

20190717_165421_resize.jpg

20190717_165513_resize.jpg

20190717_165533_resize.jpg

  • Like 3
Link to comment
Share on other sites

Great news, everyone loves a BBB, that initial excitement, then THE SHEER PANIC "I have to cut this" :laugh1:

 

Looking forward to the progress, remember when ever in doubt ask there are so many here ready to help and you have the gallery section you can fall back on.

 

Good luck.

  • Like 1
Link to comment
Share on other sites

Remember being a kid at Christmas, tearing into those gifts like there was no tomorrow?  This is sort of the same thing.  At first you think "Oh wow!"  But now, it seems like "Oh Crap... I have to put this thing together? lol.  

 

Not to worry, though.  You have an entire Detachment here to help you out every step of the way, Kris.  You did the right thing by starting your own build thread, and we are here to help!

 

Be sure to ask any and all questions you have (no matter how small) and post as many photos as you can during your build.  When in doubt, ask first before cutting or gluing.  Also, remember that building this kit will be more of a marathon than a sprint.  In other words, DON'T RUSH!  Take your time, do your research, and if there is an issue all you have to do is ask us and we will be there for you.  "Troopers helping (future) Troopers!

  • Like 1
Link to comment
Share on other sites

So I've decided to start with the helmet and TD.

I was gathering research and notes last night. I think it will be easier to tackle and focus on 

1 or 2 items at a time and hopefully not get too overwhelmed.

 

I'm still gathering some supplies, and I'm going to layout and label all the bits and pieces tonight.

 

Helmet Notes/Plans

- Helmet is pre-trimmed from AP, I've done a rough alignment of the pre-drilled holes and ear pieces

and it looks good. I have the reference photo that shows the proper angles in relation to the screws

ect. I'll post a pic prior to doing anything when I'm ready.

- I'm going to mount visor similar to SlyFox740's method. Chicago screws ordered and I'm searching 

for a new visor replacement. Going to E-6000  plates rather than Plastiweld.

- I'm going to Plastidip the inside black.

 

TD Notes/Plans

- Cut to size and paint tube

- angle/round corners of clips, flare them out and add fuzzy velcro

 

Some pre-build questions

 

For the helmet, do most pop rivet the 2 helmet sections together? 1/8" x ??? rivet size?

 

For the TD what is the proper color for the tube? I searched and only found 1 reference to a Testor color

that is not available at my local hobby shop. I did pick up some Gun Ship Metal in Tamiya brand which

was the closest cross-over they had.

 

Oh, and I picked up some 6-32 Pan screws for the TD. These look right? 

 

20190718_153604-picsayb.jpg

 

Anyways, slowly getting started.... baby steps.. lol

Edited by Lumpy
Link to comment
Share on other sites

Nice work.

 

Some use the Humbrol No5 for the TD tube, I used grey primer and clear coated.

 

Helmet and ab paint

31201091045_f616e14d58_c.jpg

 

Correct tube stripe orientation 

 

NOnMRqt.jpg

 

Screws will work and just paint them black.

 

Good luck with the build

Link to comment
Share on other sites

Thanks everyone for the tips and suggestions.

 

Just a small update for today.

 

Picked up some shop supplies.

 

 - A decent 4" belt sander

- Chicago screws assortment set for doing my helmet visor upgrade

- 1.5" velcro discs for helmet attachments down the road.

 

miBus0Y.jpg2gCgyZn.jpg

 

Getting things gathered for the TD

 

MEcfQ8S.jpg

 

Paint I picked up for the TD

 

FlAFavw.jpg

 

Unsure if these clips are right? All the reference pics look different. Thoughts???

 

Gt0R1Is.jpg

 

Just a quick bolt together, brow still too low for Stunt? or is it passable? Kinda like it the way it is.

 

X0t9BwX.jpg

 

Comments and suggestions welcome!

 

Kris

 

 

  • Like 1
Link to comment
Share on other sites

9 minutes ago, Lumpy said:

Good Day,

 

Can anyone comment on the TD clips and brow height as posted above?

 

 

TD clips are looking pretty good. That said they should continue to curve with the tube to avoid sticking out too far and possibly getting snagged on things. Brown height is acceptable IMHO though some may say it's a little low. Keep up the great work

 

TD Reference photos

gallery_12157_51_98835.jpgTD%20clip%20screws.jpg

 

 

Link to comment
Share on other sites

2 hours ago, ukswrath said:

TD clips are looking pretty good. That said they should continue to curve with the tube to avoid sticking out too far and possibly getting snagged on things. Brown height is acceptable IMHO though some may say it's a little low. Keep up the great work

 

TD Reference photos

gallery_12157_51_98835.jpgTD%20clip%20screws.jpg

 

 

 Awesome Thanks!!!! I can get the brow up slightly higher with no major mods.

 

The clips still have me worried. The second back hole is very hard to get at, where

as some of the reference pics it's further out and more accessible.

Link to comment
Share on other sites

2 hours ago, Lumpy said:

 Awesome Thanks!!!! I can get the brow up slightly higher with no major mods.

 

The clips still have me worried. The second back hole is very hard to get at, where

as some of the reference pics it's further out and more accessible.

Yours's look like they're made out of aluminum which should allow you to bend them outward to get to the screw the bend them back once installed.

 

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...