phil Posted February 17, 2019 Report Share Posted February 17, 2019 hi, nice work..how did you get knee plate to fit so well plz ? Quote Link to comment Share on other sites More sharing options...
justjoseph63[Staff] Posted February 17, 2019 Report Share Posted February 17, 2019 7 hours ago, repentance3232 said: I have a concern. I E-6000 shoulder covers for 24hrs and realize 5 bumps in the front was to much. That caused no bumps on back plate. I removed shoulder covers and reglued. The chemical in E-6000 caused the chest plate to rise in a slight deformation. I also have never heard of E-6000 reacting to ABS, and unlike CA (super) glue it does not heat up while curing. If I didn't know any better, I would say that the clamps you used to hold it on while the glue dried were really tight and actually made an indentation in the shoulder tab. The only ones I have seen you use are the plastic ones (and the metal ones for the sniper knee) which usually don't have that sort of strength. 2 Quote Link to comment Share on other sites More sharing options...
troopermaster Posted February 17, 2019 Report Share Posted February 17, 2019 E6000 can deform ABS if too much glue has been applied and if using excessive clamping force while curing. Quote Link to comment Share on other sites More sharing options...
ukswrath[Staff] Posted February 17, 2019 Report Share Posted February 17, 2019 37 minutes ago, troopermaster said: E6000 can deform ABS if too much glue has been applied and if using excessive clamping force while curing. E6000, never seen it happen. Maybe depending on the material? Clamping force yes Quote Link to comment Share on other sites More sharing options...
gmrhodes13[Staff] Posted February 17, 2019 Report Share Posted February 17, 2019 I've seen ABS distort with a particular make of snap and E6000, must have been the coating reacting with the glue and causing heat, this was on AM armor a recruit was working on, I've never come across the issue myself while building armor. Quote Link to comment Share on other sites More sharing options...
shashachu[TK] Posted February 17, 2019 Report Share Posted February 17, 2019 My guess would also be clamps or maybe unintentional bending when you pulled up the pieces? Quote Link to comment Share on other sites More sharing options...
troopermaster Posted February 17, 2019 Report Share Posted February 17, 2019 1 hour ago, ukswrath said: E6000, never seen it happen. Maybe depending on the material? Clamping force yes I think you might have misunderstood what I said. I mean using too much glue and too much clamping force together (a combination of the two) is what can cause deformation. I have not seen E6000 cause any problems on it's own but that doesn't mean it couldn't happen, especially with fake glue that's going around. Quote Link to comment Share on other sites More sharing options...
ukswrath[Staff] Posted February 17, 2019 Report Share Posted February 17, 2019 7 minutes ago, troopermaster said: I think you might have misunderstood what I said. I mean using too much glue and too much clamping force together (a combination of the two) is what can cause deformation. I have not seen E6000 cause any problems on it's own but that doesn't mean it couldn't happen, especially with fake glue that's going around. I think you maybe onto something regarding glues that are packaged looking like E6000. I've definitely seen those. Quote Link to comment Share on other sites More sharing options...
ukswrath[Staff] Posted February 17, 2019 Report Share Posted February 17, 2019 1 hour ago, gmrhodes13 said: I've seen ABS distort with a particular make of snap and E6000, must have been the coating reacting with the glue and causing heat, this was on AM armor a recruit was working on, I've never come across the issue myself while building armor. The reason it reacts with certain snaps is because of the LACK of anti-corrosive material or coating, instead it is reacting to the base metal. Marine and Military grade snaps (relatively same in price as their less protective counterparts) are made to protected against environmental exposure and corrosive chemicals. Quote Link to comment Share on other sites More sharing options...
repentance3232[TK] Posted February 18, 2019 Author Report Share Posted February 18, 2019 Believe me, I was quite surprised to see deformation after the removal of shoulder covers. It makes sense that what could have caused it was possibly both excessive glue and force from clampsSent from my SM-G965U using Tapatalk 1 Quote Link to comment Share on other sites More sharing options...
repentance3232[TK] Posted February 18, 2019 Author Report Share Posted February 18, 2019 My guess would also be clamps or maybe unintentional bending when you pulled up the pieces?I didn't bend it. I actually sliced through it with a butter knife Sent from my SM-G965U using Tapatalk Quote Link to comment Share on other sites More sharing options...
repentance3232[TK] Posted February 18, 2019 Author Report Share Posted February 18, 2019 I think you might have misunderstood what I said. I mean using too much glue and too much clamping force together (a combination of the two) is what can cause deformation. I have not seen E6000 cause any problems on it's own but that doesn't mean it couldn't happen, especially with fake glue that's going around.Hey Paul I looked to see where my E6000 was manufactured and it is in USA, not ChinaSent from my SM-G965U using Tapatalk Quote Link to comment Share on other sites More sharing options...
repentance3232[TK] Posted February 26, 2019 Author Report Share Posted February 26, 2019 Question, is the tube stripe 7mm from the cheek???Sent from my SM-G965U using Tapatalk Quote Link to comment Share on other sites More sharing options...
ukswrath[Staff] Posted February 26, 2019 Report Share Posted February 26, 2019 Roughly a #2 pencil in width. If that's equal to 7mm then yes. For the record we'll never make you pull out a ruler to prove otherwise 1 Quote Link to comment Share on other sites More sharing options...
repentance3232[TK] Posted February 26, 2019 Author Report Share Posted February 26, 2019 Thank you Ukswrath!!!Sent from my SM-G965U using Tapatalk 1 Quote Link to comment Share on other sites More sharing options...
gmrhodes13[Staff] Posted February 26, 2019 Report Share Posted February 26, 2019 FYI tube stripes can also go on two ways, but the correct way from back to front, they have a greater fall from the top, from back /////// front 2 Quote Link to comment Share on other sites More sharing options...
ukswrath[Staff] Posted February 26, 2019 Report Share Posted February 26, 2019 4 minutes ago, gmrhodes13 said: FYI tube stripes can also go on two ways, but the correct way from back to front, they have a greater fall from the top, from back /////// front Great point Glen 2 Quote Link to comment Share on other sites More sharing options...
repentance3232[TK] Posted March 3, 2019 Author Report Share Posted March 3, 2019 About to strap biceps to forearms. I going elastic but my question is what are the PRO and CONS to 1" or 2" elastic??? I'm trying to decide which I will go with. I'm not sure due to this being my first build Sent from my SM-G965U using Tapatalk Quote Link to comment Share on other sites More sharing options...
gmrhodes13[Staff] Posted March 3, 2019 Report Share Posted March 3, 2019 No real issues with either, I've not had them stretch as yet and I used 1". If you want to be a little more accurate you can go 2 inch 1 Quote Link to comment Share on other sites More sharing options...
repentance3232[TK] Posted March 3, 2019 Author Report Share Posted March 3, 2019 Thank you gmrhodes13!!!!!Sent from my SM-G965U using Tapatalk Quote Link to comment Share on other sites More sharing options...
gmrhodes13[Staff] Posted March 3, 2019 Report Share Posted March 3, 2019 My pleasure, better images below: Also a good go to guide on elastic sizes https://www.whitearmor.net/forum/topic/26477-what-we-know-about-strapping-snaps-rivets-etc/ 1 Quote Link to comment Share on other sites More sharing options...
repentance3232[TK] Posted March 12, 2019 Author Report Share Posted March 12, 2019 I have a ANH HERO and today I am planning on installing the bubble lenses. Looking to use ABS TABS to secure. The top inner eyelet seems to have to much edge. The bottom is 5mm, and top is 13mm and top wont touch ABS TABS. I feel like I need to dremel down the top and I am second guessing myself and asking for some feedback on this thought. Will I be ok to take the top down???Sent from my SM-G965U using Tapatalk Quote Link to comment Share on other sites More sharing options...
Digz Graavz[TK] Posted March 13, 2019 Report Share Posted March 13, 2019 Yeah that looks extremely thick. It should follow the contour of the brow ridge. Mine is ANH stunt, but a fairly consistent 9-10mm ridge. You can check out the hero helmet reference in the gallery here: 1 Quote Link to comment Share on other sites More sharing options...
ukswrath[Staff] Posted March 13, 2019 Report Share Posted March 13, 2019 18 hours ago, repentance3232 said: I have a ANH HERO and today I am planning on installing the bubble lenses. Looking to use ABS TABS to secure. The top inner eyelet seems to have to much edge. The bottom is 5mm, and top is 13mm and top wont touch ABS TABS. I feel like I need to dremel down the top and I am second guessing myself and asking for some feedback on this thought. Will I be ok to take the top down??? Sent from my SM-G965U using Tapatalk Hey John do you have the bubble lenses in hand? If so follow the contour of the lens 1 Quote Link to comment Share on other sites More sharing options...
repentance3232[TK] Posted March 13, 2019 Author Report Share Posted March 13, 2019 Yes I do, thank you Ukswrath!!!Sent from my SM-G965U using Tapatalk 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.