Jump to content

11B30B4's RO T-21 Build (MkI -MkIII)


Recommended Posts

  • 1 year later...

Ok guys, I trooped with this T-21 for short periods since I built it; however, for Halloween I trooped all day and I really got tired of lugging the thing. It is rather heavy since I used resin parts, plywood base, and electrical conduit. Because of this, I have built a version 2 where I built all new 3 models and made the T-21 from 3D prints, Sentra base, and used thin walled pvc and abs pipes. The models are all available on my thingiverse page for free download. Since this T-21 is also for my RO Sandtrooper, the entire build is here is anyone is interested. http://forum.mepd.net/index.php?/topic/16557-11b30b4s-ro-t-21-version-2-build/

 

  • Like 1
Link to comment
Share on other sites

  • 3 months later...

Upgrades because…

Since I am no longer working on a Sandtrooper, its just easier for me to keep all of my TK content on FISD. As previously mentioned, I posted this on MEPD but I am transferring it here for anyone who finds it useful.

 

NOTE: this build thread outlines me using ½” thick Sentra as the base material; however, the Sentra snapped at the stock after I finished the build. In March 2019, I rebuilt the gun (a third time) where I used a planed down white pine board as the base material. Everything else is the same as you will see in this build. So, I recommend you use white pine, it weights less than the plywood and is more rigid than Sentra. Finding a ½” thick board is difficult. More than likely you will find ¾” boards at any Home Depot and you will need to plane them down to ½”.

 

In my previous build I used plywood as the base material, and it is a bit heavy after trooping with it for any period of time. I also used Spool86's cast kit (heavily modified) for a lot of the parts. I like Spool86’s parts but they are not as accurate as I would like. Also, cast parts weigh more than 3D printed parts and this added to the overall weight. So, I wanted a more accurate and lighter weight T-21.

 

To this end, I have modeled a lot of the parts and 3D printed them. I will make these parts available for free download from my Thingiverse page here:  https://www.thingiverse.com/11b30b4/designs

 

So, a few notes before we begin. The overall dimensions are very close to Pandatrooper’s diagram. I will be reusing the already made stock from my original RO T-21 and some of the other parts. I hope to re-use the barrel, but I will need to determine if it will mate with the new printed parts.

 

Yoshix created a thread MEPD to discuss the RO T-21 differences but I had not seen it until now since most of my previous stuff was on FISD. A good catch was the space on the barrel before the rubber tubing. I did not build my previous T-21 with this gap in mind but I will endeavor to include it for this build.

 

Another thing that has come up has been the discussion about the aerial gunner sight. Specifically, if it is an aerial gunner’s sight or as one of my friends has suggested that it is actually a coil cable (think phone cable) as a nod to the ANH T-21 and it is just sticking up oddly.  What I am talking about is the red circles in these pics:

 

0Gf13iX.jpg

 

LO3EJ9d.jpg

 

I believe they are an aerial gunner sight and will be building my RO T-21 with this in mind.

 

Although there are five different variants of the Lewis gun and there are a ton of different manufacturers of each variant I will be primarily using the MK1 variant. There are not a lot of pictures of the RO T-21 and the ones that I have found are lacking in detail. I have collected a large number of detail pictures of actual Lewis guns from across the internet to develop the 3D models. Although I could make a completely accurate model, there are a few areas I will need to divert from to make this something more buildable. One specific thing I have omitted is the underside of the cooling vent area mid-section of the gun. Seen here (yellow outline) is what was omitted for anyone wanting to go overboard in their build.

 

yR2rGeN.jpg

 

There are a few other very minor details that I did not include in the 3D models but for the most part, they should be correct. I have embedded many of the roll marks seen on various pictures I have found. Most notably will be roll marks on the feed tray.

 

For the base material of this build I will be using ½” (12.7mm) thick Sentra. I purchased a 4’x’8 sheet of Veranda HP brand PVC board from Home Depot for $69.00. Obviously, you will not need a whole sheet of this stuff but its hard to find in smaller quantities. Sentra is PVC board and Veranda is just a different brand.

 

Keep in mind that I am working within the limitations of Tinkercad as I am not a CAD engineer. That being said, here are the models I have built so far.

 

This is the main feed tray cover, mid-section cooling vents and vent housing.

 

iW8AFEz.jpg

 

5c20cI4.jpg

 

This is the center feed tray, ejector, feed operating arm, rear sight mount, forward feed tray, and assembly pegs.

 

WEIo4X4.jpg

 

rjbAqdc.jpg

 

Receiver left side.

 

U0294Ce.jpg

 

3UP5ktm.jpg

 

Receiver right side.

 

hZUDKaR.jpg

 

pTFggaL.jpg

 

Rear receiver and stock mounting plate.

 

t899aV1.jpg

 

AzHMPeh.jpg

 

I have already started printing these parts and here are some of the raw prints before finishing.

 

RkUh3oD.jpg

 

iMsn9d7.jpg

 

NUkQtsJ.jpg

 

8qejBM1.jpg

 

BFhU8Qp.jpg

 

I have a Prusa I3 Mk3 and I use MatterHackers MH Build series 1.75mm ABS filament. Some tips on printing:

 

Any of the parts with horizontal holes or overhangs should be supported. I printed everything in ABS and to prevent any elephant foot (warping near the build plate) I printed everything with a brim. As for detail I used 0.07mm ultradetail with a fill of 15% for anything that had any detail. I printed the receiver rear and stock mounting plate at 0.10 detail with all the same settings for fill, brim, and support.

 

Update 12/2/19

 

I have added a few additional 3D models to my Thingiverse for this build.

 

First, I redesigned the rear sight mount. I added the rear sight with roll marks and adjustment knob and combined them with the receiver rear and stock mount plate

 

cGeG3e1.jpg

 

NJCoEFn.jpg

 

I modified my T-21 transition to fit a Shop Vac Extension Wand (read further to understand why) and included the front radiator and flash hider, a backing for the radiator, the front end cap ring, and two barrel ends for the sides of the receiver.

 

WEgJNqT.jpg

 

h0093s3.jpg

 

Lastly, I finished the models off with the two end caps for the oil brush that are mounted in the stock, the front sight, the trigger, and the gas key adjustment lever.

 

mJ2BxiV.jpg

 

JflI5wP.jpg

 

Once I finished the models, I printed them, and they came out great. I should note that each file is printed in 0.07 Ultradetail which takes about 30 hours.

 

jdLh5gd.jpg

 

aekITdT.jpg

 

After printing, everything got sanded and cleaned.

 

0dmsna4.jpg

 

After cleaning, everything got primer and then paint.

 

MzBWQsu.jpg

 

Next, using Pandatrooper’s pattern and making some minor alterations, I cut the rifle out of Sentra. Once I had the shape, I started to dry fit parts and figure out where things would sit. Initially I was using a larger PVC pipe for the sides of the receiver and in these pictures, the lines you see where for the larger pipe. Here I was working out the trigger and test fitting the trigger guard. I reused the trigger from my previous T-21 but I have made a 3D model for anyone wanting to print one.

 

YQaoJMG.jpg

 

cnPXSWa.jpg

 

Around this time, I realized the pipe I was using was a bit larger than I wanted so I found some ¾” SDR 21 PVC pipe which is irrigation thin wall PVC. I used this pipe along with a section of ½” Schedule 40 PVC pipe to make the side barrels on the receiver.

 

pfAtIAB.jpg

 

I cut each pipe lengthwise in half then sanded them. Next, I drilled the ejection port and finished it with the dremmel. Next, I painted the ¾” pipes black and the ½” pipe silver. I glued the ½” pipe inside the ¾” pipe and then test fit them on the gun. Notice the remainder of the glue line under the new pipe, from the larger pipe I removed. This size pipe better aligns with the barrel part of the radiator.

 

efzpoau.jpg

 

Next, I needed to replace the top aerial gun sight that is seen on the Rogue One version of the T-21. On my previous build I used an iron pipe I-bolt. Since reducing weight was one of my primary goals, I needed to find a new solution. I eventually decided to make the sight out of aluminum. I took some aluminum stock and worked it on my metal lathe. Next, I threaded the parts then cleaned the parts for painting.

 

wM91ijV.jpg

 

I also needed to remake the aluminum legs that protrude from the stock mounting plate and into the stock. Once everything was cleaned, I painted all the parts with a black bake on metal paint I use for gunsmithing. While the parts were baking, I took a hard look at my previous T-21 to determine what were the heavy parts. As I stated previously, the base of the T-21 was plywood and the switch to Sentra seamed to reduce the weight buy more than half. All the resin parts on the previous T-21 were heavy as well and switching them with 3D parts further reduced the weight. Switching from the Iron sight to an aluminum one reduced the weight; however, I soon realized that one of the heaviest parts on the previous T-21 was at the extreme front end of the gun, the 2.5” electrical conduit I used for the tapered bore of the barrel shroud was very heavy. I originally used this part because the outside diameter was 2.75”. I looked for a good replacement, but I had very little luck. I could special order a pipe with the outside diameter of 2.75” but most of the options were either too expensive, the wrong material like acrylic, had too thick a wall, or weighed too much. I was forced to consider a pipe with an outside diameter of 2.5” and again I was hard pressed to find a light weight option. Eventually, I found a shop vac extension wand a Lowes that had an outside diameter of 2.5” at one end and tapered to 2.25” at the other end of its 20” length. I only needed about 7” in length and if I measured the seven inches from the larger end the outside diameter of the smaller end would be just shy of 2.5”. The wand was fairly thin walled (about 1/8”) and very light. So about $8.00 this should work.

 

mPlHNUN.jpg

 

I reworked the T-21 transition 3D model and included it on my Thingiverse page. So with all the parts gathered I continued to assemble the T-21.

 

68e6TSb.jpg

 

Next, I looked over the reference pictures and discovered that there are only two rings visible on the large part of the barrel shroud. One about 2” from the rear of the shroud and one with the front sight attached to it. There is also only one on the smaller part of the shroud at the extreme front of the barrel. So since I was reusing the barrel from my previous build I needed to remove some of the rings, fill some holes, re-score the exposed parts of the shroud and re-apply the rubber tubing. I used ¼” windshield washer tube for this. I added 4 mounting screw holes near the rear of the shroud that will be covered by the rear most ring and will make the barrel removable for easy transport. I still need to apply the feed tray parts and grips and finish painting then do a black/ brown wash over the whole thing to weather it but it is coming along nicely and the weight is amazingly very very light. I wish I had though to weigh the previous gun for a comparison, but I would say this thing will end up being 1/4 -1/3 the weight of the previous version.

 

OXukowU.jpg

 

Update 12/5/2019

 

I assembled the radiator, flash hider, back plate, and end cap ring on the tapered part of the barrel shroud. Next, I installed the tapered barrel shroud to the transition then I dry-brushed silver on all the parts and attached the Feed operating arm, ejector, and the barrel ends on the sides of the receiver. I used E6000 to adhere the grip scales then masked off the radiator and bolt and applied a weathering wash comprised of black acrylic and light brown. Once this dried, I applied a flat clear coat over the whole rifle.

 

m4mqXQX.jpg

 

1yo6uk6.jpg

 

NLPUWbY.jpg

 

I think the dry brush will look more natural in these pics. I did the black wash over the dry brush and it mutes the silver. I am inclined to agree with you about using bondo between the transition and the two parts of the shroud. The line between the transition should not be as defined; how that change will need to wait a bit before I can address it. For anyone interested the total estimated weight of the T-21 is 4.5 pounds.

 

ca6l3Ku.jpg

 

tMDkEue.jpg

 

Cqv8fFr.jpg

 

zfY71cs.jpg

 

3HbFkSE.jpg

 

yyqX1II.jpg

 

vcOIWkX.jpg

 

5qaQmYh.jpg

 

A45pF48.jpg

 

Back on topic, the stock is white pine, as are the grips. I made the stock for the previous version of the ROT-21 and re-purposed it here. The stock consists of two halves roughly ¾” thick and 8” x 18” once I have the outside rough shape, I hollowed out the interior with a router then glued the two halves together. The stain is Minwax Ebony with a satin clear coat on top.

 

 

 

As for the strap, from the best images I could find I determined the width of the sling webbing to be 1.25” and the webbing to be black nylon webbing (most likely Mil Spec: MIL-W-4088 Type 10, Class 1A). At one time I made tactical gear and I am familiar with webbings and types.

 

Some things to note from my research: In this screen grab you can see where and how the forward end of the sling is attached (Yellow Circle) and it looks to be an AK-47 sling mount screwed to the top of the barrel shroud just behind the front sight. Note the round (looks to be an areal gunner sight) sight just forward of the feed tray and is in the dead space of the barrel shroud between the two barrel shroud rings (Red Circle). Also note the rubber wrapped tubbing on the barrel shroud goes past and covers the middle barrel shroud ring (between the Red Circle and Yellow Circle). Lastly, note the rear sling mount appears to be on the side of the stock (Light Green Circle) and is most likely in the spot as the bras ID disk seen on some Lewis Guns. An assumption can be made that they are using an Uncle Mikes style sling mount and quick detach since this has been used on several weapons from Rogue One.

 

0Gf13iX.jpg

 

LO3EJ9d.jpg

 

I hope this build helps others out in making RO T-21s and feel free to ask question and/or point out anything I missed.

 

Update March 2 2019

So Sentra was not the best idea I have ever had. The T-21 snapped where the stock meets the receiver when I snagged it going through a door. Since plywood was too  heavy and the Sentra was too weak, I have rebuilt the rifle again using all the previous parts but this time I used a 3/4" white pine board that I planed down to 1/2" thick and seems to be holding up great and the weight is fine.

 

Thanks for the interest.

  • Like 4
Link to comment
Share on other sites

  • 2 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...