gmrhodes13[Staff] Posted May 24, 2018 Report Share Posted May 24, 2018 Congratulations trooper Quote Link to comment Share on other sites More sharing options...
CableGuy[Admin] Posted May 24, 2018 Report Share Posted May 24, 2018 Congrats, Jose. Welcome to EI. :-)Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
José[TK] Posted May 24, 2018 Author Report Share Posted May 24, 2018 Thanks you! I going yo work hard for the next leves! I promise 1 Quote Link to comment Share on other sites More sharing options...
Traumtrooper[TK] Posted May 24, 2018 Report Share Posted May 24, 2018 Welcome and congrats Bro! I see you next Saturday in SOLO! Enjoy your new grade and be proud of it Quote Link to comment Share on other sites More sharing options...
lucnak[TK] Posted May 24, 2018 Report Share Posted May 24, 2018 Congrats on your EIB! Quote Link to comment Share on other sites More sharing options...
ToniML[TK] Posted May 24, 2018 Report Share Posted May 24, 2018 Congratulations José for your EIB level Enviado desde mi Redmi Note 4 mediante Tapatalk Quote Link to comment Share on other sites More sharing options...
José[TK] Posted May 24, 2018 Author Report Share Posted May 24, 2018 (edited) 15 hours ago, justjoseph63 said: Bueno, Jose, thank you for your EI application, so let's take a look, mi hermano! CRL and EIB Application Requirements: All required submission photos have been posted and it appears that everything is in order, so I would like to be the first to welcome you to the rank of EI! Other-Armor Fit/Assembly: In this section we review observations made by your fellow troopers and ourselves. Some observations may lead to suggestions to improve the overall look of your armor. 1. The small ab-button plate could definitely use some trimming on the sides as seen in the photo below: Reference image 2. We noticed your rivet heads look a bit large... Please check that your rivets are the correct size. Thanks! The CRL states: Three rivets, approximately 5/16 ' (8mm) diameter, are present on the left side of the kidney plate. 3. The posterior needs to reside under the kidney with little or no gap.. I would suggest shortening or replacing the strapping Reference photo 4. Tube stripes should be approximately 8-9 cm from the face and consistent on both sides. Reference image 5. The stripes and outlines on the back of your bucket are absolutely spectacular, brother, but the ones on the tears are a bit thick. A few dabs of gray paint can easily remedy this! Reference image 6. Your left and right shoulder bells should be a bit closer to the shoulder bridge. An easy fix! Reference image 7. Quite a few of your coverstrips need to be trimmed down to where that are flush with the armor. Reference photo The gap of your ab/kidney connection on the right should be no more than half an inch wide at most. You may be able to fix this by tightening the strapping. There can be no gap for level 3. Reference image 8. Your blaster will need some work, brother. The Hengstler counter looks great, but the rest of it will require some serious sanding/filling to get rid of the 3-D print lines to get you to level 3. Reference images Reference photo Centurion Suggestions:In this section we prepare you the best we can for Centurion. If there are any areas of concern they will be discussed here. Great job on your armor, Jose, but in order to get you to level 3 there are a few areas that will need some attention. After seeing the time and care you took on this build I am confident you should be able to get there with just a couple of hours of work.! Reference photo The ab button pate will need to be replaced, as these are not acceptable for level 3 as per the CRL. "Abdomen buttons are integrated and painted directly on the armor. No separate buttons are allowed". Reference image For the rear of the shoulder bridges, you will need to pick up some white elastic as per the CRL. "The plastic shoulder straps need to be held down in the back via a white elastic band to the white fabric that connects/bridges the chest and back piece". Reference photo The outer edge of the drop boxes should align with the outside edge of the ABS belt acording to the CRL. "Drop boxes are vertically aligned with the end of the ammo belt with minimal gap between belt and box". Reference photo For level 3, there can be no gap of the ab/kidney on the right or left side. Again, this may be just a strapping issue and easy to fix. Reference image Congratulations on your EI achievement, Trooper! You have made the Spanish Garrison proud by reaching this level, and although you have some work to do, I am confident after that after it is complete I will see your Centurion application! Thanks yo very much... what is the process to get the certification in paper? Edited May 24, 2018 by José Quote Link to comment Share on other sites More sharing options...
justjoseph63[Staff] Posted May 24, 2018 Report Share Posted May 24, 2018 Here is the link, sir! https://www.whitearmor.net/forum/topic/40769-request-your-eib-certificate-here/ Quote Link to comment Share on other sites More sharing options...
acetilacetato[TK] Posted June 11, 2018 Report Share Posted June 11, 2018 Congrats trooper Quote Link to comment Share on other sites More sharing options...
Thumpy~[501st] Posted June 12, 2018 Report Share Posted June 12, 2018 Nicely done! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.