Jump to content

T-21 Light Repeating Blaster Build


Recommended Posts

So looking over the different types of Imperial Storm Troopers I decided that I would build a Heavy Weapons Specialist, not the SandTrooper but a standard Imperial Storm Trooper, that way I would technically have two uniforms to wear trooping.

Now having looked online for kits I was lucky enough to come across the incredible scratch build by PandaTrooper TK-2886 whom also went above and beyond the call of duty and made a template! So a very big thank you to him for sharing his build log and plans which were the driving force, guide and inspiration for my first 1:1 scale scratch build project in the Star Wars Universe.

The build log and the template can be found here http://www.whitearmor.net/forum/topic/11017-how-to-t-21-blaster-scratch-build/

I tried several attempts to get the printer to get the correct scale but after several attempts both messing with the printer setting and the scale of the template I decided to go to Kinko and just have the print it out on a plotter roll, which cost me ¥2,116 JPY. The first attempt misprinted and missed out part of the barrel - they were very apologetic and printed a fresh version that was perfect and asked if I wanted the misprint - luck was in my favor as I can use the misprint as my templates that I will use to cut the wood and plastic parts while the good copy I will use for reference.

Here are the materials I will be using; again this is pulled directly from PandaTrooper's original post with the metric conversion added for ease of use by myself. I will update the list and correct in red if there are better alternatives available or if I feel that I need.

Materials
2cm – (3/4 “ inch) thick wood (I used pine shelving)for the main body / receiver
1cm (3/8” inch) thick wood for the stock (I couldn’t find any, so I used ¼”)
8.9cm (3.5”) diameter PVC pipe for the main barrel (I used 3” “Cell core” ABS pipe, which has an outer diameter of approx 3.5”)
8.9cm (3.5”) connector (you will cut rings from this)
6.35cm (2.5”) diameter PVC pipe for the barrel tip (I couldn’t find any locally, so I took some 3” PVC and cut it down to 2 7/8” diameter)
10.16cm (4”) corrugated drain tubing for the barrel (you can use D profile adhesive rubber trim for car doors for more accuracy)
Sheet styrene for details (I used 2mm and 1.5mm a lot)
3.17cm (1.25”) piping (small section for the sight)
5cm (2”) PVC piping (for the chamber or whatever you call it that holds the bullets in the main body / receiver )
Tools
Jig saw / scroll saw
Saw for cutting large sections / straight lines
Dremel
Files
Sandpaper
Clamps (spring clamps like you used for armor)
Rivet gun / rivets (1/8”)
Craft / exacto knife
Adhesives, etc.
E-6000
Wood glue
Plastic weld (styrene glue)
Bondo
Various screws / bolts (use what you have around the house)
Tamiya Black Primer L
Tamiya Flat Black
Tamiya Gun Metal

Dark brown for the stock - I intend to keep the stock wood and stain it brown to keep the wood grain or to paint a grain in.
Gold or silver for the cooling vents
Any other paints you want to weather the blaster (silver, gunmetal, bronze, etc..)

Link to comment
Share on other sites

So today I went shopping!

It's not everything needed for the build but enough to get started on the maint receiver and some of the other parts.

f1pZ2y3.jpg

Using multiple copies of the template I glued them directly to the wood, time to get cutting!!

2eeq07v.jpg

Edited by FarEast
Link to comment
Share on other sites

MONy9bi.jpg

 

cggogFM.jpg

 

iv5guR4.jpg
 

0Rira0L.jpg

Lh1EO2S.jpg

So already I've found several items that aren't in the original walk through and I will add them later.

Wife said I was looking a little peaky this afternoon, I guess she knows best - calling it a day and taking an early night!

Edited by FarEast
Link to comment
Share on other sites

I'm still ill but no point laying in bed.

Today I decided to detail the receiver.

3o438K7.jpg

 

aqZLn7E.jpg

J5GX9rV.jpg

 

Now that's set aside to cure I can start work on the sight.

 

I need more images of the original 1916 flip up sight but very happy with the results so far.

c4PnV2y.jpg

 

ClgcuzK.jpg

 

hUBmNmf.jpg

 

fnBgCRT.jpg?1

 

XrJOjhx.jpg

Edited by FarEast
Link to comment
Share on other sites

Outstanding job so far, James!  This should be a great help to those aiming for HWT, which I am glad to hear you are heading for.  (I may be just a bit biased, though...)   ;)

As soon as you get your HWT approved, PM me and I will send you a patch! (below)  If I can be of any help with your build or supplies, just let me know.

 

3yTikF9.jpg?1

Link to comment
Share on other sites

On 27/06/2017 at 11:29 PM, justjoseph63 said:

Outstanding job so far, James!  This should be a great help to those aiming for HWT, which I am glad to hear you are heading for.  (I may be just a bit biased, though...)   ;)

As soon as you get your HWT approved, PM me and I will send you a patch! (below)  If I can be of any help with your build or supplies, just let me know.

 

3yTikF9.jpg?1

That's awesome - Bought a sander today and a few other bits of hardware so this weekend I plan to get the cooling jacket cut to size and then start on the receiver set.

I have some great photos of the Lewis gun courtesy of Sir. Peter Jacksons collection of all people  which I overlaid on to PandaTroopers template at 1:1 scale - Think I may need to make some changes!

lewis overlay right.jpg

Link to comment
Share on other sites

Also it seems that Photobucket has finally decided we all need to pay, so the new forum update couldn't have come at a better time.

 

So for those that haven't seen the build so far here are the latest shots. - The magazine mount has had the locking wedge glued on so technically its all done, although I'm a little tempted to sculpt the bullet feed on the upper receiver!

19424312_10154901197954247_7735526631608727001_n.jpg

19437336_10154901209409247_7375507694345347268_n.jpg

Link to comment
Share on other sites

So Yesterday night I cut the cooling jacket for the T-21 and laid everything out on the master plans. 4QHl1gw.jpg So the first job of the day was to sand the stock in to shape, the new sander really helped out, remember use a respirator and eye protection! XgtkSlF.jpg# yupohOb.jpg Once done I made a butt plate out of 2mm plasticard - to get it to retain its shape you can leave it to sit in boiling water for a minute or two then once cooled it will retain its shape. UpvmwUt.jpg vOOwvkc.jpg Having gone over my references I will be changing out the round headed screws for flat head. From here it's time to assemble the Upper and Lower Receiver and the Cooling Jacket. Bttt933.jpg dfKqaHx.jpg  

Edited by FarEast
Link to comment
Share on other sites

So last night I decided to mark out the detailing at the end of the cooling jacket just before it attaches to the upper receiver.

 

mv8lYon.jpg

 

ESNV1iA.jpg

 

As well as mark out all the detailing on where the stock joins the receiver.

 

5b5jWsp.jpg

 

 

Link to comment
Share on other sites

WOW!  What can I say, James.. your attention to detail is fantastic, and I can't wait to see the finished product!!  If I may make a suggestion, when it comes time for the tubing around the barrel I used 1/4 inch thick windshield washer hose.  After looking everywhere for something to use on my Hyperfirm, I found it in an auto parts store, sold by the foot.

I cut it into 12 inch sections (yours may differ) and glued it on using E-6000.  The joins are at the bottom as no one sees them anyway.  I used a few feet extra for the tube that extends along the side and over the top.

Keep up the great work!!!!  :jc_doublethumbup:

 

KYw0ZfL.jpg?3

  • Like 1
Link to comment
Share on other sites

24 minutes ago, justjoseph63 said:

WOW!  What can I say, James.. your attention to detail is fantastic, and I can't wait to see the finished product!!  If I may make a suggestion, when it comes time for the tubing around the barrel I used 1/4 inch thick windshield washer hose.  After looking everywhere for something to use on my Hyperfirm, I found it in an auto parts store, sold by the foot.

I cut it into 12 inch sections (yours may differ) and glued it on using E-6000.  The joins are at the bottom as no one sees them anyway.  I used a few feet extra for the tube that extends along the side and over the top.

Keep up the great work!!!!  :jc_doublethumbup:

 

KYw0ZfL.jpg?3

 

 

Many thanks for the kind words, I kind of break down each part in to its own separate project and only jump to another part if the fitting or build requires it. I have to admit 1:1 scale is a whole lot easier then my usual medium of 1:32 or 1:16 

Lw45sZz.jpg

 

I have a few options for the ribbing on the cooling jacket but I want to complete the Lewis Gun before modifying it into the T21 Blaster as this gives me a much more solid foundation to build on.

Also I'm wondering where those additional parts above and below the cooling jacket come from are there any reference photos of them?
 

Link to comment
Share on other sites

I'm not sure of reference pics of them right off hand, but you may want to get in touch with Roger (spOOL68).  He makes those and many other parts (including the cooling fins) from resin.  I have used a lot of them, including the rear sight, and actually replaced the entire deck of my Hyperfirm with his resin one (I am bit of a detail freak, LOL).  Using these may save you a bit of work.

Here is a link to his sales thread:  

 

Link to comment
Share on other sites

1 hour ago, justjoseph63 said:

I'm not sure of reference pics of them right off hand, but you may want to get in touch with Roger (spOOL68).  He makes those and many other parts (including the cooling fins) from resin.  I have used a lot of them, including the rear sight, and actually replaced the entire deck of my Hyperfirm with his resin one (I am bit of a detail freak, LOL).  Using these may save you a bit of work.

Here is a link to his sales thread:  

 

 

Yeah, I saw his parts but I'm not sure how accurate those two pieces actually are to the ones seen in ANH and RO. Thus the question about referencing. I will continue to burn the diode out on my blueray!! Haha!

 

I pretty much plan on building the entire thing from scratch as I have a huge amount of reference material on the Lewis Gun from other works WWI Aviation related, the hunt is still on for the reduce diameter section of the cooling jacket!

 

Edited by FarEast
Link to comment
Share on other sites

So next up is the final piece of detailing on the upper receiver which has basically resulted in my thinking that I may need to recut the barrel again due to scaling issues - no biggie, just if I don't its going to bug the hell out of me! 

 

This is a really quick and easy way to work on parts - lay some heavy 3M masking tape, draw directly on to it, transfer tape to PLAPLATE, cut and appy.

 

LPOuaZq.jpg

 

The part requires it to be bent around and down and slightly covers the cooling fins - these were bent using Tamiya Poly Cement on the back of the piece, this causes a chemical reaction and basically melts the plastic, while its going through this reaction you can bend it which is whats going on here. If it snaps, no problem we can just use filler.

ET9WpA1.jpg

Link to comment
Share on other sites

So on reflection I really didn't like the thickness of the barrel end so I decided a rebuild was in order.

 

This time I tapered the end of the cooling jacket and measured the overlap so that I would only have the thickness of the bracing ring at the end off the jacket which matches the original.

 

2Kb6SEX.jpg

 

OlMaU1L.jpg

 

OJHrTkV.jpg

 

wSAXZ1W.jpg

 

Much happier with the overall finish here.

GL2Wkde.jpg

 

Link to comment
Share on other sites

Next up was the gas recoil tube and the outer barrel section on the receiver.

 

I marked off the visible area and removed it - then cut a matching section of tube and bonded.

 

GO9dOJd.jpg

 

TxZS4Os.jpg

 

The outer barrel that the cooling fins would be attached to was just down to size and then the receiver detailing around the two was constructed.

PC1Thg6.jpg

epuylN9.jpg

Next up was the cooling fins that extend out along the barrel. This was a real labor of love.

AWm9j9w.jpg

7Kgq639.jpg

These were bonded to the outer barrel using carbon epoxy - when this cures the bond is incredibly strong and its very difficult to break it.

I used a hairdrier to speed the chemical process along a little.

4QvsRNs.jpg

 

F6anwKR.jpg

 

The fins totally surround the barrel so again I continued the process around the the inside of the cooling jacket. Two fins were left off for access that I will need for sanding and cleaning the finish of some of the fins.

NK42nyc.jpg

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...