Jump to content

Stephen's RS ANH stunt build WIP (for small people)


Gwithian

Recommended Posts

Well after a lot of reading and research both on here and the UKG I finally took the plunge, well read that as I've dipped my toe in the water, what I mean is I've ordered and now received an ABS ANH lid from RS propmasters :)<br><br>

It's in kit form so I need to cut our the eyes and teeth, fit the ears and the thing that's worrying me most, paint the tubes, well that will come later. <br><br>

I'm thinking if I can do the lid then hopefully, and that's a big hopefully for a small guy, I may be able to trim and put together the armour. Crickets build in here has been an inspiration, thanks <br><br>

I'm so pleased that I went with RS, they are a northern business in Manchester which is only 20 miles from me, so it's good to support local businesses. I must admit I was blown away, in a good way when I opened the box on Christmas Day, yes the lid is wonky , yes it's bumpy and yes it's awsome :), I am well chuffed with it and can't wait to get the armour, but first things first, I need to build my lid :)<br><br>

This is the pic I took after opening the box, hopefully it will work<br><br>

The next pics I have pencilled in where I think I should cut the teeth out and the eyes, the second pic has two lines on it at the top, I'm not too sure whether to cut the top or bottom line, your thoughts are appreciated :)<br><br><br>

I intend to drill some small hole some in the teeth and eyes with a hand drill and then cut them out with an x-acto knife, I will post some WIP pics . The guys on the UKG have been kind enough to tell me what colour humbrol paint to get for the lid, so that will be my next purchase.<br><br>

I would like to say thank you to all members on here, especially those who have taken the time to pull together how to threads, WIP threads and instructional videos plus the do's and don'ts when it comes to purchasing your TK armour, you have all helped a complete novice to take the first step toward success becoming a member (hopefully) of the 501st, thank you all :)

  • Like 3
Link to comment
Share on other sites

Ok will try and post the pics from my phone, first one brown box day

 

517b92856b75a0c57a7f50bee47fa43d.jpg

 

Now where I have drawn the lines for the teeth and eyes, question mark regarding the lines fir the eyes, which is right, top line or bottom line?

 

b094f14709d50949bd4e22bcae5b7f1c.jpg

 

e1f2d44e44c05f75978b0683d355381d.jpg

 

 

 

Sent from my iPhone using Tapatalk

Link to comment
Share on other sites

Ok work has started today, drilled some 3mm holes in the eyes and big teeth and 2mm holes in the rest, now starting to cut it out, it's a slow job, one slip and I will have a toothless TK , so I will take my time, slowly, slowly catch the monkey as they say

 

Some pics

 

36efd8046a610fc65df43fae9dfb39ed.jpg

 

dc3cb3a58cf57c1f29e5fec4691cbbd1.jpg

 

792ca3f39c2c9076dd51a43ff3bd42a7.jpg

 

f70fbdce486ef5e3b39cd60bcde8a832.jpg

 

671534457d160c623d7f8f621abf228a.jpg

 

5c9b55625d1f5e23f92688ef11afad11.jpg

 

d654e33f553b9584128761da506432fe.jpg

 

I'm enjoying this :)

 

 

Sent from my iPhone using Tapatalk

Link to comment
Share on other sites

Today's progress :)

 

ca8d9c643fed15f29dc79178e99a8c01.jpg

 

2271917d55de030842e287fd8df26ad0.jpg

 

5b26c4a8f602eb4d16741abc1d693725.jpg

 

eb02b1b29f06d9d00cd65c93dde98df1.jpg

 

ea7dcad823ef628891c632cdb8d7d270.jpg

 

8e05e34c35a94d6a9dccea8db788a101.jpg

 

3e3ab0a08fcff7961262b306dd047ad9.jpg

 

Is the gap between the teeth looking ok? I've filed it a bit, also do the eyes look ok.

 

Thanks :)

 

 

Sent from my iPhone using Tapatalk

Link to comment
Share on other sites

Hey Stephen,

 

I'm not an experienced builder myself, but I'd say you could trim the eyes a bit more, especially the right one (right when wearing it, that is) - it looks a little "sleepy", if you know what I mean

 

Regarding the teeth, I think you can leave it as it is - maybe take a millimeter of the bottom, and perhaps slant the top part a bit so it follows the contour of the frown more? Just a suggestion, I hope I'm making sense ☺

 

Sincerely,

 

Christian

 

 

Sent from my iPhone using Tapatalk

  • Like 1
Link to comment
Share on other sites

Thanks Christian, I will tweak the eye and the tooth and make it follow the contour of the frown. It's not until other people point things out that you see where it needs tweaking, it's a bit like the old saying "you can't see the wood for the trees" <br><br>

Once again, many thanks :)

Link to comment
Share on other sites

Ok I've tweaked the eyes and finished the teeth, next job cut out both half of the lid, drawn some lines where I think I need to cut. Any advice, thanks :)

 

3381e5e45c0861c2c8dca2896b610096.jpg

 

d56ca493b408b514aaf3b687c864401f.jpg

 

c1d6fd44b1ab2e622a8854c2780171e4.jpg

 

7f73a5d5ce9128e271a1277f58c29015.jpg

 

64f9746cd4af17d0e2d7c3c5f8487f67.jpg

 

Thanks

 

 

Sent from my iPhone using Tapatalk

Link to comment
Share on other sites

Hey Stephen,

 

In my humble opinion, your eyes and teeth look great ☺ and I think your cut lines look fine too, so I'd say you can go ahead and trim the faceplate and the cap and back

 

I'm sure you've already researched a lot, but when I assembled my helmet, this thread helped me a lot - even though it is not an RS helmet:

 

http://www.whitearmor.net/forum/tutorials/article/1-howto-assembling-ata-abs-helmet-1/

 

This one too:

 

http://www.whitearmor.net/forum/topic/28633-howto-ata-helmet-build-hand-painted-details-pic-heavy/

 

Hope it helps ☺

 

Sincerely,

 

-Christian

 

 

Sent from my iPhone using Tapatalk

  • Like 2
Link to comment
Share on other sites

Thanks for the advice Christian, I must admit I think the right eye as you suggested looks better now that I have trimmed more if, plus the teeth following the frown look better also. <br><br>

Thanks also for the links, I have copied the links to my iPad and will look at them now. <br><br>

I really appreciate your help :)<br><br>

Stephen

Link to comment
Share on other sites

Ok I have trimmed the forehead today and fitted the brow, I think it's a bit lob-sided as the tube curves on the cap don't line up with the face and when I make them line up then the brow is lower on the left side as you look at it , but then the top of the cap doesn't seem straight . Also the recesses above the brow are 1 inch deep in the right as you look at it and 1.25 inches deep on the left, should these be the same?

 

37cb46b07ca4fa845d0b4991415d7243.jpg

 

511e81362e82024a73765b8c7484df64.jpg

 

1f8a93f877cd8449c79b51843914a30b.jpg

 

cb545db8b1b05175068b84f1a9905ff0.jpg

 

Thanks

 

 

 

Sent from my iPhone using Tapatalk

Link to comment
Share on other sites

I don't think you should worry too much about the cheek tubes aligning; the ears will cover them anyway ☺ If I were you I'd focus on getting the brow line positioned correctly and centered properly, first and foremost - when the ears come on, you won't notice any misalignment between the front and back of the tubes ☺

 

 

Sent from my iPhone using Tapatalk

  • Like 2
Link to comment
Share on other sites

Christian has been right with his suggestions. The ears will cover and "hide" any misalignment of the cheek tubes. Having the front aligned properly is more important.

 

Eyes and teeth look excellent. The eyes could be smoothed a bit more, but you have them in a great position now.

 

My only addition at this point is to be careful when you attach the parts of the helmet. Are you planning to use just the ear screws, or did you intend to rivet the pieces together first, then add the ear screws later? The reason I ask... I used rivets to put together the cap and face, and accidentally put the rivet very close to where the ear screws ended up later. It didn't keep it from working in the long run, but did cause me to be concerned.

Edited by Sentry71
  • Like 1
Link to comment
Share on other sites

Thanks for the advice, it's very much appreciated. I was intending to use some small bolts initially (instead of the rivets) whilst I sort the ears out and decide how I'm going to fit the lenses , that way if I need to take it all apart later I can. Once everything is finalised I can rivet it. On the RS lid there are bumps where the rivets and ear screws go which I guess are where they were in the original, so I'm hoping, fingers crossed , that they will be ok . :)

 

 

Sent from my iPhone using Tapatalk

  • Like 1
Link to comment
Share on other sites

That positioning is looking good ☺ I'm not sure that you can rely 100% on those bumps for drilling the holes, though, so be sure to use your common sense as well ☺ I ended up with a few extra holes in my helmet, but they are all covered by the ears, so it doesn't show at all.

 

-Christian

 

 

Sent from my iPhone using Tapatalk

  • Like 1
Link to comment
Share on other sites

Ok I have attached the cap to the face with some small bolts and plastic washers, this is only temporary until I rivet it in place. How does this look?

 

4ff1e653b1f68f441a5e6af581eb77b9.jpg

 

75251f2905982582052e5a0f6b58752a.jpg

 

I am looking at the ears and wondering if the top two screws have to be vertical ? , does this look right?

 

1bb2e9719e0a1849c81a951465f3c2aa.jpg

 

604ee32bca1e52bb1d11c1c6ab7b19c3.jpg

 

8e473591662bb66bf49941f8ffc93e84.jpg

 

Thanks

 

 

Sent from my iPhone using Tapatalk

Link to comment
Share on other sites

Ok today I have tweaked the brow , looking at centurion applications on FISD their brows seemed lower, I think this looks better . 57539a1ccb9b6b7d843c6389d84746d8.jpg

 

It's still only bolted together . Will rivet it when I'm happy with it , been trimming the left ear as well, not got a pic of that sorry

 

c2e76541b4b2e9eee6fb5adac40af93e.jpg

 

Now the right side, well I've messed it up a bit, well a lot actually, doh, I've drilled so many holes in it I will need to fill some with abs paint, doh,

 

b2dff89989808c1b1d97679001bbb8fe.jpg

 

Some will be hidden behind the ears, some won't

 

Now I know it's two rivets and three ear bolts that hold the cap and face together , can you use more than two rivets? It's just that the cap and face aren't fitting flush on each side, it is flush around the brow

 

Thanks

 

 

Sent from my iPhone using Tapatalk

Edited by Gwithian
Link to comment
Share on other sites

Fitted the left ear the other day and started painting with satin black, still got the right ear to do but decided to paint because I wanted a break from ears

 

165898bb99814da3fb45b63d3a70cd7a.jpg

 

9e8a043861cdcec450c7c6931c62fb10.jpg

 

f580334b47f49530ec8c5859df002d0b.jpg

 

a2861b9d90449e067de07fbff2912c8d.jpg

 

06b05851d1b101f490af5189d051328d.jpg

 

7777f0306157610b46decbcc0e80ca89.jpg

 

 

 

 

 

 

 

Sent from my iPhone using Tapatalk

Link to comment
Share on other sites

Done the first coat of grey today, needs another cost and a bit of the black needs touching up.

 

Is the width of the black boarders ok or is it too wide?

 

Thanks

 

f76b8ffb5a5e42d2385706a24305a8f7.jpg

 

d167c7b78b406d35d8f5006ee7e8cd64.jpg

 

 

 

Sent from my iPhone using Tapatalk

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...