lagces[TK] Posted October 13, 2016 Report Share Posted October 13, 2016 (edited) Name: Luis Guillen 501st Id: TK-41975 Name FISD forum: lagces GARRISON: Garrison Peru 501st STATUS: http://www.501st.com...hp?userID=17749 Required information Armor Maker: RS Propmasters Helmet Maker: RS Propmasters Blaster Type: E-11 Height: 5' 7" Weight:187lbs Boots Maker: TK Boots Canvas Belt: Clothears costumes Hand plates: RS Propmaster Latex hand guards white painted Neck Seal Maker: Diana Caldas Gayoso Holster Maker: Full Body Armor Details Helmet Details Blaster Details Accessory Details Edited October 13, 2016 by lagces Quote Link to comment Share on other sites More sharing options...
justjoseph63[Staff] Posted October 13, 2016 Report Share Posted October 13, 2016 Hi Luis! Great looking armor from the front, but unfortunately you are missing quite a few photos. For a complete list of required pics, go to this thread http://www.whitearmor.net/forum/topic/22604-expert-infantry-application-photo-checklist/. 1 Quote Link to comment Share on other sites More sharing options...
lagces[TK] Posted October 13, 2016 Author Report Share Posted October 13, 2016 Thanks a lot!, I will be back with the missing pictures, Best, Quote Link to comment Share on other sites More sharing options...
CrookKnight[TK] Posted October 13, 2016 Report Share Posted October 13, 2016 Looking good so far. Can't wait to see the other photos. Quote Link to comment Share on other sites More sharing options...
lagces[TK] Posted October 13, 2016 Author Report Share Posted October 13, 2016 Thanks again!, I already edited post with full set, waiting very anxious for your feedback, Thanks! Luis Quote Link to comment Share on other sites More sharing options...
CrookKnight[TK] Posted October 14, 2016 Report Share Posted October 14, 2016 Armor is looking good. One observation or question, or you able to walk well in the armor. I noticed your COD plate is covering the upper portion of your thigh armor. Does this rub when you walk? Also, it seem you have the opposite issue on the butt plate where it is tucking under your rear thigh armor. You may want to adjust this as it could be uncomfortable. Could be a simple issue that your lower body armor is sitting too low. A simple solution would be to add a suspension system (like suspenders) to hold the lower portion higher. I have these in my armor. It is 2 inch wide black elastic with velcro on the ends that I use as suspenders. Not sure if this will be an issue with your application, I will leave that up to the experts. Looking good. Quote Link to comment Share on other sites More sharing options...
lagces[TK] Posted October 14, 2016 Author Report Share Posted October 14, 2016 Thanks a lot, Shawn, I use a harness that allows me to graduate the height of the legs. Tomorrow we are having a tropping and I will try to use little lower to see your point I appreciate your comment, Best Quote Link to comment Share on other sites More sharing options...
Sly11[Admin] Posted October 19, 2016 Report Share Posted October 19, 2016 Hey Luis, could you please post up a photo of the end of your blaster showing the D ring. Thanks for your patience we shall be with you soon. Quote Link to comment Share on other sites More sharing options...
Sly11[Admin] Posted October 20, 2016 Report Share Posted October 20, 2016 Hi again Luis It apperas that your sniper plate is riveted on, unfortunately, this is not allowed at EIB level, so we kindly request that you renove them and make some ABS paste to neatly fill the holes, take some new photos and post them up when your done. CRL For level two certification (if applicable): Sniper knee plate must be aligned with the ridges on the shin. Sniper knee plate must not have visible rivets or fasteners attaching it to the shin. Quote Link to comment Share on other sites More sharing options...
sylverbard[TK] Posted October 20, 2016 Report Share Posted October 20, 2016 The right side of the ab kidney has a large gap, and the right side doesn't but the rivets dont line up. Quote Link to comment Share on other sites More sharing options...
lagces[TK] Posted October 22, 2016 Author Report Share Posted October 22, 2016 (edited) Hello Guys thanks a lot for yours feedbacks, let me fix the issues then I'll post the pictures, best, Edited October 22, 2016 by lagces Quote Link to comment Share on other sites More sharing options...
hlehman1[TK] Posted October 27, 2016 Report Share Posted October 27, 2016 Hi there, I am considering buyin a RS Propmaster straight-out-of the box ready to wear. Did you do some modifications and how wennt your application? Any Problems? Regards Hendrick Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.