Jump to content

TK 5924 Requesting (ANH STUNT) EIB status [Anovos] [625]


Recommended Posts

Hi Guys!  

 

Well, it's that time again!  I'm looking forward to humbly presenting my most recent build for EIB consideration.    I purchased an Anovos kit on the first tier round and FINALLY got around to finishing this baby up!   Really fun build!  It looks great and troops really solid!  I couldn't be more satisfied!

 

And away we go!............

 

Name: Carlos Mendoza
Legion ID: TK 5924
Forum Name: Solcar23
Garrison: Midwest Garrison
501st Member Page: http://www.501st.com/members/displaymemberdetails.php?userID=14790
Height: 5'9"
Weight: 175
Armor maker: Anovos
Helmet maker: Anovos
Blaster: Doopydoos full kit
Canvas Belt: Gazmosis
Holster: Gazmosis
Hand Plates: Latex/Trooperbay
Electronics: Icomm voice changer/ Aker
Boots maker: TK Boots/Size 11
Neckseal: Anovos

 

And now the pictures.....

 

Front - Arms at side:

 

01%20-%20Front%20-%20Arms%20at%20side_zp

 

 

Back - Arms at side:

 

02%20-%20Back%20-%20Arms%20at%20side_zps

 

Left - Arms raised:

 

03%20-%20Left%20-%20Arms%20raised_zpsar1

 

Right - Arms raised:

 

04%20-%20Right%20-%20Arms%20raised_zpsom

 

Because I see that the "Han" snap didn't show in the pic, here's an extra to present that detail.

 

Right side "Han" snap detail:

 

05a%20Right%20Side%20quotHanquot%20Snap_

 

Right side detail:

 

05%20Right%20Side%20Detail_zps0nbbqig8.j

 

Left side detail:

 

06%20-%20Left%20Side%20Detail_zpszngdqto

 

 

I did a redo of the lid following Gazmosis' post on the subject.  The frown has been repainted, correct screws installed, its pop riveted together, better more accurate brow trim, the tube stripes are Trooperbay replacements for the decal that was there.  The lenses were also custom cut and installed as per Gaz's post, using hockey helmet screws embedded in abs stacks.   The helmet is also Plasti-Dipped on the inside with MICH pads for support.

 

Helmet front:

 

07%20-%20Helmet%20Front_zps91hybpxy.jpg

 

Helmet right side:

 

08%20-%20Helmet%20Right%20Side_zpsriuubs

 

Helmet left side:

 

09%20-%20Helmet%20Left%20Side_zps1xsacto

 

Helmet back:

 

10%20-%20Helmet%20Back_zps4ug9slml.jpg

 

Hovi-Mic Tip detail (upgraded to correct mesh):

 

11%20-%20Hovi-Mic%20Tip%20Detail_zpsngcb

 

Lens color:

 

12%20-%20Lens%20Color_zpsve5lzvqd.jpg

 

Helmet interior:

 

29%20-%20Helmet%20Interior_zpstihqv0lw.j

 

Canvas belt and holster (upgraded):

 

13%20-%20Canvas%20Belt%20-%20Front_zpsit

 

Neckseal:

 

14%20-%20Neck%20Seal_zpsqtaemlqz.jpg

 

Blaster left side:

 

15%20-%20Blaster%20Left%20Side_zpsxxntjg

 

Blaster right side

 

16%20-%20Blaster%20Right%20Side_zpsznyht

 

Thermal Det Back:

 

17%20-%20Thermal%20Det%20Rear%201_zpsdg2

 

Internal Strapping:

 

18%20-%20Interior%20Strapping_zpslpnoaiy

 

Cod to butt plate attachment:

 

19%20-%20Cod%20to%20Butt%20Plate%20Attac

 

Ab detail:

 

20%20-%20Ab%20Detail_zpswlyzuoxj.jpg

 

Holster Attachment:

 

21%20-%20Holster%20Attachment_zpsdgdcvgt

 

Action Pose:

 

22%20-%20Action%20Pose%201_zpsob46skab.j

 

Lid off:

 

23%20-%20Lid%20Off_zps8fsfe6jl.jpg

 

Thanks for your consideration!

Edited by Solcar23
Link to comment
Share on other sites

No prob, give me just a min. You can also check my Centurion request (I was a little pro-active). It's also there

 

 

Sent from my iPhone using Tapatalk

Edited by Solcar23
Link to comment
Share on other sites

Hey Carlos welcome and thank you for your EI application. Lets see what we have here..

CRL and EIB Application Requirements:

All submission photos have been posted. Your armor displays all the necessary elements to qualify for Expert Infantry. Congratulations trooper!     :salute:

 

Other-Armor Fit/Assembly:

In this section we review your armour in detail and make suggestions that will help make you look the best you can. If any of these recommendations would effect this or a future application, it is stated in the above and below sections.

Firstly, this is a great application, to show some of the improvements that can be made to an Anovos kit for screen accuracy. Thanks for refining the helmet points that we talk about so often when reviewing Anovos armour. If anything I would still make the vocoder outline shape a little more prominent.

 

0720-20Helmet20Front_zps5uyqjndg.jpg

 

f316cad4-5241-4f0a-ae1b-9bd96b67b348.jpg

 

 

The only other item to mention is the gap between your shoulder bell tops and the plastic shoulder bridges. Just bring them in so they virtually touch

0120-20Front20-20Arms20at20side_zpszyzjz

 

Shoulder%20gap.jpg

Centurion Suggestions:

Because Centurion photos show much more detail than EIB, items pertaining to Centurion might be seen there and not here. We try to point out all we can from what is seen but the final accuracy is the responsibility of the trooper. This is also where we try and get you in the best possible position for a successful Centurion application.

We can happily say that there isnt anything that stands out, which is excellent.

Make sure you include a photo of the back of your belt so we can see the drop boxes are enclosed at the rear, as well as all other photos on the Centurion check list.

 

Congratulations yet again for a very clean set of armour and an easy application.

Make your fine tuning and we will see you in Centurion soon. :jc_doublethumbup:

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...