ChaseM Posted May 3, 2016 Report Share Posted May 3, 2016 Hey everyone! I received my kit a couple of weeks ago. Tonight I started out using a dremel to sand down the teeth. I smoothed it out using a needle file. Also, I looked at my hand plates and to me it seems that I have two right hands? Quote Link to comment Share on other sites More sharing options...
T K[501st] Posted May 3, 2016 Report Share Posted May 3, 2016 Here's the pic from the crl... but I know little to nothing about ESB/ROTJ hand plates, so someone else will have to chime in to be sure. Good luck! Quote Link to comment Share on other sites More sharing options...
ChaseM Posted May 3, 2016 Author Report Share Posted May 3, 2016 Here's the pic from the crl... but I know little to nothing about ESB/ROTJ hand plates, so someone else will have to chime in to be sure. Good luck! Yeah I have read some other build threads and looked at the CRL. There doesn't seem to be any really clear pictures to compare. But it looks like mine are duplicates. Quote Link to comment Share on other sites More sharing options...
T K[501st] Posted May 3, 2016 Report Share Posted May 3, 2016 Yeah I have read some other build threads and looked at the CRL. There doesn't seem to be any really clear pictures to compare. But it looks like mine are duplicates. I agree on that . Quote Link to comment Share on other sites More sharing options...
cjdesign[TK] Posted May 3, 2016 Report Share Posted May 3, 2016 (edited) Also, I looked at my hand plates and to me it seems that I have two right hands? I would agree they are the same. I created a left and right by sculpting them with the index finger area being higher then the pinkie. see example ESB Hand Covers/Plates http://www.whitearmo...build/?p=436879 Edited May 4, 2016 by cjdesign Quote Link to comment Share on other sites More sharing options...
ComradeDave[TK] Posted May 3, 2016 Report Share Posted May 3, 2016 you can take a look at my build thread too, This is how I did mine I put my hand in the respective plate and traced around the top of my hand Quote Link to comment Share on other sites More sharing options...
ChaseM Posted May 14, 2016 Author Report Share Posted May 14, 2016 I just finished gluing the back of the helmet to the crown. I'm a little OCD and this is the tightest I could get the seam to fit. Any suggestions on how to hide these gaps? What about getting rid of excess glue in between the seam? Quote Link to comment Share on other sites More sharing options...
ehinote2187[TK] Posted June 1, 2016 Report Share Posted June 1, 2016 You can try to hide the gaps with some ABS slurry (made with ABS trimmings and 100% acetone. Put trimmings into a jar and just barely cover with the acetone and let sit so the ABS melts into a paste) and fill it in with that. If you do this, there will be sanding involved to get smooth, then you'll have to buff out the scratches and use the Novus polish to get shiny again. Personally, I left my helmet alone with this seam, and it didn't hinder me getting approved. As far as the excess glue, use either a dentist hook or exacto knife to try and get all the excess stuff out. Be VERY careful in doing this, you don't wish to have any nics or scratches all along the bucket. Hope this helps! Quote Link to comment Share on other sites More sharing options...
SheaJeff[TK] Posted June 1, 2016 Report Share Posted June 1, 2016 I just glued the back to the top on mine and have this gap as well. I wasn't excited about it but others told me they have the same thing. Quote Link to comment Share on other sites More sharing options...
cjdesign[TK] Posted June 2, 2016 Report Share Posted June 2, 2016 (edited) I just finished gluing the back of the helmet to the crown. I'm a little OCD and this is the tightest I could get the seam to fit. Any suggestions on how to hide these gaps? What about getting rid of excess glue in between the seam? I used dap water based white bathroom caulking. Works great! wipe off the excess with damp rag. In hind site I would have left mine alone. nobody looks at that stuff anyhow... but I get it. LOL e6000 can be removed but buffing with a microfiber cloth. Edited June 2, 2016 by cjdesign Quote Link to comment Share on other sites More sharing options...
SheaJeff[TK] Posted June 2, 2016 Report Share Posted June 2, 2016 Here's mine. Opinions? Quote Link to comment Share on other sites More sharing options...
cjdesign[TK] Posted June 5, 2016 Report Share Posted June 5, 2016 (edited) I would not touch that seam. Sometimes the quest to make something perfect ends with dread and remorse. I re glued my cap and back 3 times because I felt the space was too big. Thank goodness for e6000. if you really want to fill that gap use a water base solution as mentioned above. Don't like it - wipe it off. my 2 cents. Edited June 5, 2016 by cjdesign Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.