Jump to content

themaninthesuitcase Anovos ANH Stunt Build


Recommended Posts

Righty then, more progress.

The first (right I think) do over on the rear thigh cover strip worked nicely.

25020859394_a82c03dcb5_z.jpg

As you can see I was heavy handed with the glue, lots of squeeze out. Once I released the clamps the cover strip actually bent a little to the shape of the curve so pretty happy with the glue bond this time.

25283796429_ac2d91fc65_z.jpg

Did the left last night and will be leaving it until tomorrow to allow the glue to truly set.

Next I made a start on the drilling. I needed 2 sizes, one for the snaps and one for the rivets. I found a piece of 1mm scrap and after I measured the parts found the nearest (but small) drills and made some test holes.

25532660562_2665105bba_z.jpg

I used some imperial HSS drills I have as I have them in 1/64th increments. I used 5/32 for the rivets and 11/64 for the snaps.

After using a 1mm ish drill in a pin vice to create a pilot hole I drilled out all the marked holes.

25024632273_36e3bcbb95_z.jpg

Kidney, 10mm in NOT 20 like Anovos instructions...

25283791619_864f5a3710_z.jpg

Ab, also 10mm in. Nice solid material here.

25020847134_dd23b78365_z.jpg

The hole for the single snap on the ab plate. About 20mm in and down to give the appearance of the correct space.

25283783699_d6e91002a7_z.jpg25020843944_6ea5bb8383_z.jpg

The snap set. The material is a bit thin for the tool so the snap was a bit rattly despite being set well. To prevent too much movement and so wear I super glued the inner part of the snap. I did this for all the snaps in the plastic.

25532655132_8bcb1bac89_z.jpg
25651378115_80885c334d_z.jpg

Butt plate snaps, again super glued. Can't tell you the exact measurements but where based on ukswrzaths build one FISD adjusted for the different snaps.

I've not done any of the split rivets yet as I forgot to pick up my small cold chisels when I was back at my dads at the weekend. I won't be back again for a while so I'll just order some new (better) ones.

I also made some progress on the TD.

25020837454_2147df2354_z.jpg

First I offered up, marked, then drilled for the brackets. They should be right up against the end caps once I add them, if not they should be pretty close. The letters are so I know which bracket goes on which side.

25625185916_11aac29b69_z.jpg

I also drilled another 4mm hole under where the control plate will be. The purpose of this is to allow the air to escape when fitting the end caps hopefully making this easier.

25558682411_b39187d794_z.jpg

I'll be using M4 pan head machine screws for the brackets. These will be secured by a washer and a nyloc nut on the inside. To better match the originals I've applied a layer of satin black Humrol (#85) to 5 screws, 1 spare. I need to do a 2nd coat looking at it now it's dry so I'll do that soon.

25532647982_ecbc836c66_z.jpg

I also did the ab buttons with the #14 French Blue. I of course managed to drop the plate after the photo so had to touch it up. Looking at it today theres a few marks I'm not massively happy with so may use a light smear of white spirit to smooth and then re-do the top coat again. I have a test piece I'll try this on before the buttons to see how will it works. If it goes bad I'll leave it as is, you'd have to be inches away to notice.

I did have HUGE issue with the #5 grey though. It was clearly very old and had completely separated. After 10 minutes of mixing it was far too light looking. I did a test on my scrap and even once dry it was way too light. I got my Humbrol from a small local hobby store and the tin was obviously old. From the 5 tins I got I had 3 different tin print styles. The grey was clearly the oldest as was the Mediterranean blue for the bucket stripes. My black had also settled a lot, after a good stir it was okay for the screw heads but no good for the bucket, far too thin.

I will be replacing the #5 grey, #85 satin black and #48 Mediterranean blue with new tins. The #22 white was new a looking design and the #14 was fine with a quick stir. For what the paint costs I feel this is just easier.

Normally I like to support local shops where I can but Humbrol has become a pain to find* so I'll be ordering it direct after I finish this post. I'll also get some gloss varnish so to use to seal the masking template and prevent the blue from bleeding.

when I was a kid I could have gone to 3-4 places in town, now maybe I have to go to Hobby Craft in an out of town place.

Edited by themaninthesuitcase
  • Like 1
Link to comment
Share on other sites

I wish you were local; I'd be happy to let you borrow my paint bottles. It's silly that we have to buy a whole bottle just for these tiny spots of paint, but I guess it's not bad to have them in your kit for future touch ups!

  • Like 1
Link to comment
Share on other sites

Not long ago I started a to do list using Trello.

 

For those interested it's publicly viewable here:

https://trello.com/b/6Iy1Plmi/anovos

 

The items with blue are needed for EIB and the red for Centurion. No colour means JFDI.

 

I think I'm starting to get close to finishing the armour. Then all I need to do is finish the E-11....

  • Like 2
Link to comment
Share on other sites

I got my helmet pads in the post today so started a basic disassembly of the bucket.

 

The hard hat liner came out easily and basic testing of the pads looks like the will work well.

 

I also removed the S trim to allow me to repaint the vocoder as the standard paint job was less than great.

 

Under the s trim I found 1 small crack. I've drilled a small hole at the end of it to stress relieve and stop it running. I will make some abs paste and fill from the back to reinforce it.

 

They also where a bit heavy handed with the CA glue when building these. I've got some CA remover but it melts the ABS. I've added a layer of CA to my test sheet and will see if I can use a cotton bud to at least thin down the glue a bit in the worst areas.

 

 

I will redo the frown as well as the paint wasn't great but unless there's any pressing need will leave the tube stripes and traps for later. I will eventually do them again but for now they seem okay.

Link to comment
Share on other sites

You Americans have it so easy. Went to buy some acetone and you can't get it in bottles larger than 50ml and I was asked what I wanted it for. Fortuately, despite some confused looks, I managed to get 2 bottles.

 

I am probably now on a government list though, as the reason you can't buy it in large amounts (easily) is it's used in bomb making.

  • Like 2
Link to comment
Share on other sites

You Americans have it so easy. Went to buy some acetone and you can't get it in bottles larger than 50ml and I was asked what I wanted it for. Fortuately, despite some confused looks, I managed to get 2 bottles.

 

I am probably now on a government list though, as the reason you can't buy it in large amounts (easily) is it's used in bomb making.

It's usually used for stripping off paint. (such as why it's a primary ingredient in nail polish remover)

 

Comes standard in 1000 ml cans, or even 1 gal cans. Bizarre that it would be difficult to get. I can't imagine what your farmers must go through for fertilizer!

Link to comment
Share on other sites

I can get it in 0.5l cans but it means an order to a specialist supplier who will probably be required to keep a record of the sale.

 

Loads of stuff you can get in the US is a controlled substance here.

  • Like 1
Link to comment
Share on other sites

Does the UK have anything equivalent to our Home Depot/Lowes? Maybe it'll be easier to get at one of those type of stores

B&Q, Homebase and a few others. But like I say it's more it's a controlled substance and you have to have a good reason to have it. I asked in the shop I got some in and they said they couldn't get the bigger ones as its used for bomb making.

 

I have a link to a place that sells stuff like fibre glass supplies who sell it but if I can get it on the high street I save on expensive shipping.

Link to comment
Share on other sites

TK build update: all the images edition.

I'll start with some images from the other day.

As I said I found a crack under the S trim on the bucket.

25097133313_f4e4a3d804_z.jpg

I used a pin vice to hand drill a small hole at the end of a crack, around 1.5mm, I didn't check the size just picked one. The point of this is to stop the crack running. They use this on drum cymbals when they crack to save them.

25097132843_77dc024cee_z.jpg

If you look the crack is right at the end of a thick layer of superglue that was used to hold the trim. This created a stress point which then cracked. Not shown was the rough as badgers cut job of the bucket. I used a file and some 180 to smooth this off, again to try and reduce the risk of further cracks.

I picked up 2 50ml bottles of acetone at a (support your) local pharmacy. I've chopped up some scrap and added about 30ml of the acetone in a baby food jar. Cleaned first obviously. This has sat for 2 days now and is pretty nicely brewed. Tomorrow I'll sand off as much of the super glue as I dare and then I'll apply some paste to the crack.

I also took the clamps of the 2nd thigh. Again the big *rude word* clamp did the job and the strip bent again when the clamp was removed.

25097130243_d32b575478_z.jpg

I was testing the flex on a shoulder bell to see if I needed to trim more return and discovered the answer: yes, because it can't flex properly so cracked.  :6: 

25723742135_91cd3c304e_z.jpg

Again I will need to fix this with some ABS paste. For this one I'll probably use a square or triangular file to add a V profile along the crack and then fill this with paste to give a strong bond with minimal need to sand back. Once that's done I'll reduce the return a small amount.

I also added a 2nd coat of Humbrol #85 satin black to the M4 pan heads I am using on the TD. The result is pretty decent.

25423011780_7346e977d5_z.jpg

I also picked up some organisation for all the screws and such needed for the build.

25723739365_f986d2a3c5_z.jpg

This has my split rivets, M4 screws, nuts and washers and the M3.5 for the helmet. I also now have some bobbins for the sewing machine for the white and black threads as well as some more M4 washers to use with my split rivets.

Yesterday I sat a sewing machine for a couple of hours and made lots and lots of elastics. I've not done all of them but most of them and made a few spares for some. I still need to finish the shoulder 2" white, make a crotch strap and probably re-do the elastic for the side with the solo snap.

No images, because sewing was too hard for my fragile brain.

Now on to todays work.

I got a top tip to make a snap tool with a sawn off flat head screw driver, hence forth special tool #1.

After a lot of practice, and several dead rivets and snaps I more or less got the technique down and braved the armour.

25766985875_ea8ba478ed_z.jpg

I did all 7 rivets needed, the 6 on the ab/kidney and the front crotch. I am probably 100% happy with about 3 of them and 1 of them will have to do as I couldn't get it out. I got better as I went but I figured out a few things 2 of which are important. 1: be picky about the rivet, they aren't all cut the same make sure you pick one that's cut all the way down, some aren't cut that low and I think these are the ones I had issues with. 2: You need to "sway" the special tool #1 as you hammer to apply even pressure to both legs.

I'll do a tutorial on this later if people want it.

The result is a nice set of snaps:

25140394203_14cbd2a71f_z.jpg

That means I can completely remove the elastics.

25466295340_24cbe1d60e_z.jpg

And will still pass centurion once I paint them.

25646020472_762e497a91_z.jpg

I also started to build up the TD. I used 4 of the painted M4 screws so the head was against the aluminium bracket, a washer against the tube and then a nyloc nut. I chose nyloc as I don't want to have to pull the caps because of a loose screw. These are also stainless steel as that's all I could get the screws in rather than being extra fancy.

25671899631_9d9b229fa3_z.jpg

To fit the end caps I got a pan and pre heated it with some hot water from the tap while I boiled a kettle. This was so the boiling water stayed hot rather than heated the pan.

25466293400_d036887fe9_z.jpg

1 at a time I removed the cover plastic and dropped the cap into the boiling water for 30s. I used the spoon to hold them in the water and also to remove them after the time was up. I did my best to drain the water then dropped them on the glass on top of my oven. This was chosen as it's heat resistant and smooth so not to add texture in the next step.

Finally I pressed the tube into the cap. Now these were nice and warm the tube went in easily where before just starting to fit them was a nightmare. The chamfer added earlier made lining this up and starting nice and easy. Once fitted the plastic was set by putting it under a cold tap.

25466291560_71d255ef77_z.jpg

The caps look nice, have butted up against the clips nicely and only a small ripple on one side where the plastic stretched.

  • Like 2
Link to comment
Share on other sites

Love reading all these thread builds and getting a lot tips on building my own suit. How do I start my own thread I can't seam to find anyway of writing one on tapatalk

 

Maybe try to start it on a real computer, and then update from Tapatalk as usual, if that's more convenient?

Link to comment
Share on other sites

When you fix the crack at the bottom of your shoulder bell, CA glue two small pieces of ABS behind the crack. One on the inside of the return edge and the other where the crack continues up the bell. This will stop the crack from travelling any further if the bell is pushed out of shape at any stage. Then apply your ABS paste to the outside, if the crack S still visible and you are concerned about it.

 

 

Sent from my iPad using Tapatalk

Link to comment
Share on other sites

Delivery from Hornby!

25817777896_95822bec44_z.jpg

For reference Hornby will charge you £5 for delivery then not actually bother to dispatch for a week...

After fixing the shoulder bell I promptly broke it again the following morning testing the fix.  :duimomlaag: 

So I did it again.

25843821735_a5665e477a_z.jpg

Bit heavier on the outside this time. This will need to be sanded but as it's the under side I'm hoping it won't be too visible.

25817775726_21047e919b_z.jpg

I also embedded a small strip of offcuts scrap into some paste on the back to help reinforce the break as I will possibly need to heat bend the bell out a bit.

The other night I glued the plate onto the TD thus completing the first whole part on this build. Huzzah. It still needs the white plastics polishing though.

25748720871_16389d0085_z.jpg

The evening I glued up the TD I started dissasembling the bucket to clean up the paint.

I spent some time filing out some of the eyes to get them closer to a reference image: http://img.photobucket.com/albums/v336/themaninthesuitcase/TK%20Reference/DaveM3_zpsww1ihblr.jpg

25213660704_6cf29b7bf2_z.jpg

I probably could go farther but the reference image has a small return edge there and I was worried about messing up.

I also tested the M3.5 screws for size and they look pretty close to the same bucket I referenced before but from the side.

25543483490_4a05bf3020_z.jpg

DaveM6_zps4mxt7ljk.jpg

If you look you also get to see the ear gaps on the Anovos buckets is nice and accurate as is the brow trim not running all the way to the corner. Also of note is where the bottom ear screw is. Far higher than any builds I've seen which have it as on the Anovos kit, hidden under the S trim.

Most of this evening was spent stripping the sloppy Anovos paint job from the bucket.

25543127570_744c2cd729_z.jpg

The frown was removed using the Humbrol enamel thinners. Required some elbow grease but worked nicely. Bit tricky to get into the corners but some cotton wool on a tooth pick did the job.

The thinners also made short work of the transfers used for the tear and tube striped. These rubbed of pretty fast so I'll used the same stuff for the traps once I but some more. Top tip: the 28ml bottle is not going to be enough!

For the vocoder I had a harder time. The thinners was barely touching it, small dark marks on the cotton wool but I'd need a bucket full to get far. The white spirit I used to clean some glue from the inside padding just made it shiny. Only when I used some IPA (Isopropyl alcohol, not the ale...) and saw it went black when I wiped over did I find a chemical that would shift it! This stuff is going to make a huge mess. You can see I've only made a start but this will need a few goings over to first remove the paint, then again to clean up the mess where the IPA has flowed whilst cleaning off the paint leaving specs of paint

I stopped for the evening as at this point the wife was high as hell as she wasn't provided with appropriate PPE. I should fire the site manager.

Once the paint is all off I'll give the bucket a polish before re-assembling with some auto polish to give it a nice shine, the paint removal has dulled it even further than it was before. After that it gets painted and put back together. With any luck I'll be able to get some more thinners a bit faster than waiting for Hornby.

  • Like 2
Link to comment
Share on other sites

Had a bit of a scare this evening. Spent more time with the IPA and cotton balls cleaning off the vocoder paint. As expected this made a bit of a mess.

 

However when I went back over these areas with some clean IPA it wasn't shifting, and was all over the main face, crap. I was hoping it was going to buff out but my stock of polish has obviously gone bad so was only fit for the bin.

 

Fortunately I had a tiny bit of thinners left (a lot seems to have gone for the angels share...) which wiped it straight off. So let this be a lesson to all of us: buy the big one. I did for the rest of the order so not sure why I didn't for the thinners. Now I have to try find more in hobbycraft at the weekend.

 

No pictures as its not too different than the last and I'm sure most have seen a plain face plate before.

Link to comment
Share on other sites

Chris, where did you buy those M3.5 screws? I'm looking for those but they are not so easy to find, at least not in stores. M3 and M4 are easy, but not M3.5.

 

Are you using the humbrol thinners to strip the grey paint?

Link to comment
Share on other sites

Mine came from here:

 

http://www.spaldingfasteners.co.uk/

 

I got a bag of 10 along with washers and metric (course) nuts. Wasn't very expensive, £3.06.

 

The humbrol enable thinners (not acrylic) made short work of the transfers. It works on the frown but was harder work and used a fair bit. The vocoder was Isopropyl Alcohol to get most of it off then the thinners to clean up.

 

Get the 125ml thinners as it evaporates fast and you need a fair bit. I think I've lost about 1/5 of the 28ml to evaporation but this is probably down to the small jar size.

Link to comment
Share on other sites

I can get it in 0.5l cans but it means an order to a specialist supplier who will probably be required to keep a record of the sale.

 

Loads of stuff you can get in the US is a controlled substance here.

 

It happens here in the states too.

To buy my leather contact cement in 1gal cans I have to have a proper business tax registry. Otherwise the most they can sell to an individual is 1qt at a time.

Because, somehow, glue is more dangerous than gallons at a time of petrol. :/

:smiley-sw013:

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...