Jump to content
ukswrath

Ukswrath's ANOVOS TK build (stunt)

Recommended Posts

 
Oh okay I see. I think both front cover strips for the thighs and calves needed to be 20mm? And then fro both backs I was gonna do 25mm. Is this correct?
Sorry, back of the thighs

Sent from my SM-G955U using Tapatalk

Share this post


Link to post
Share on other sites
Backhoe the thigh cover strips are 20mm also. Only the calves have 25mm

Sent from my SM-G955U using Tapatalk



Ah okay. So thigh front: 20mm. Thigh back: 20mm. Calves front 20mm. Calves back: 25mm.


Sent from my iPhone using Tapatalk

Share this post


Link to post
Share on other sites
On 9/1/2017 at 9:20 PM, ukswrath said:

Well you can re-glue them or add the Centurion level straps and see how they sit. Another option if you're afraid to damaged them just add some white velcro to hold them in place. 

...or maybe hot bath the tabs on either chest or back?
I (and others) definitely has to round out the sharp curves of the Anovos back plate tabs

just something to look at, especially if you are tall

  • Like 1

Share this post


Link to post
Share on other sites

 

Good luck trooper!!!

 

Edited by BDWC
wrong thread

Share this post


Link to post
Share on other sites

Help.    I measured the biceps, fitted the plastic.   And after gluing they barely fit.   I need to remove the armpit six strip an reglue wider.   How do I remove e6000 .... Help.    PS. I bought abs if I need to just cut a new strip.  

 

 

Share this post


Link to post
Share on other sites

Sorry for the delay. Before tearing apart the armor have you removed all the return edge in the areas effected? This will increase the gap.

If yes then simply take a butter knife and slide it between the cover and armor at one end and slide it down separating the two.

Sent from my SM-G955U using Tapatalk
 

Share this post


Link to post
Share on other sites

Hey Tony, question for Centurion approval. Does the top-right non-functional male snap on the ab piece need to be the "S" popper snap for Centurion approval or can it be a Line 24 male snap? And I suppose same question for the belt-to-ab snaps. Would appreciate your input, thank you!

Share this post


Link to post
Share on other sites
On 9/27/2017 at 7:51 AM, ukswrath said:

Sorry for the delay. Before tearing apart the armor have you removed all the return edge in the areas effected? This will increase the gap.

If yes then simply take a butter knife and slide it between the cover and armor at one end and slide it down separating the two.

Sent from my SM-G955U using Tapatalk
 

Thanks .  I bought abs plastic to make shims.   I can't flex in it.. At all.   Thank you!

 

Share this post


Link to post
Share on other sites

So I'm a bit confused because the new ANOVOS belts no longer come assembled. I'm not sure what fixtures to use to attache the plastic, what measurements to use where, etc. Is there a guide starting with what ANOVOS now supplies? Thanks

Share this post


Link to post
Share on other sites
25 minutes ago, RubberSlug said:

So I'm a bit confused because the new ANOVOS belts no longer come assembled. I'm not sure what fixtures to use to attache the plastic, what measurements to use where, etc. Is there a guide starting with what ANOVOS now supplies? Thanks

Hey Charlie do you have a photo of the new belt assembly?

Share this post


Link to post
Share on other sites

Thanks, Tony. Reposting these from the FB group for posterity:

 

uG2TxvO.jpg

 

yVAeh6h.jpg

 

sRYApWN.jpg

Edited by RubberSlug

Share this post


Link to post
Share on other sites

Came into an Anovos TK kit and looking to build to to Centurion out of the box.

 

What, exactly makes the included belt non-accurate? Width? Out of curiosity.

 

Also if I’m understanding the process correctly I would still want to apply for/receive EIB first before Centurion?

Share this post


Link to post
Share on other sites
52 minutes ago, cinderbike said:

Came into an Anovos TK kit and looking to build to to Centurion out of the box.

 

What, exactly makes the included belt non-accurate? Width? Out of curiosity.

 

Also if I’m understanding the process correctly I would still want to apply for/receive EIB first before Centurion?

Hello, the costume as a whole is a mixture of two different types, Hero and Stunt. Out of the box it's 501st approved however, for Stunt EIB the two upper holster screws will need to be remove and the holes plugged. For Centurion the belt itself is too flimsy for accuracy standards. We're either recommending or requiring the belt be replaced to avoid any issues at the higher levels accuracy.

 

 

Share this post


Link to post
Share on other sites

Is there a source for the 'correct' mic tip mesh material? Didn't see it in your materials list (I probably skimmed over it).

Share this post


Link to post
Share on other sites
3 hours ago, cinderbike said:

Is there a source for the 'correct' mic tip mesh material? Didn't see it in your materials list (I probably skimmed over it).

I don't have the tech specs in front of me (on vaca) but I'll do you one better, here's where you cab buy it.

 

  • Like 1

Share this post


Link to post
Share on other sites

Tony, will the dropbox elastic need to be riveted at the back for Centurion or is that just an accuracy suggestion?

Share this post


Link to post
Share on other sites
Tony, will the dropbox elastic need to be riveted at the back for Centurion or is that just an accuracy suggestion?
No. There's no requirement how it's attached at any level

Sent from my SM-G955U using Tapatalk

Share this post


Link to post
Share on other sites

Never mind Sir. I surrender. I need to go back to the drawing board. Do more research. I feel that I am not an ideal size for this armor and will need to make some adjustments to get it to fit. I am 5'7" with a stocky build. and Yup, I need to drop about 8 lbs. 

 

 

Hello again, 

 

sorry to be a pain in the butt. I am a little confused by the thigh assembly and all the extra cut lines and trimming. I am guessing this is all for a good fit to your leg?  I was really hoping to have this done tonight but not looking good. Thank you for all your help. 

Edited by Falc1

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

×
×
  • Create New...