Jump to content

TK 92912 Requesting ANH Stunt EIB[ATA][472]


Recommended Posts

Name : Todd Murray

TK ID: TK92912

FISD: Devilmaan

Garrison: Great Lakes Garrison

501st Status: http://www.501st.com/members/displaymember.php?userID=18451&costumeID=124

 

Armor: ATA

Helmet: ATA

Blaster: Doopy Doo Kit

 

Height: 6'

Weight: 208lbs

Boots: Painted

Canvas Belt: TKittell

Hand Plates: Trooperbay

Electronics: IComm+Aker amp

Neck Seal: Darmen

Holster: Darmen

 

 

Front

IMG_3059.jpg

 

Back

IMG_3062.jpg

 

Right (arm raised)

IMG_3067.jpg

 

Left(arm raised)

IMG_3065.jpg

 

Left (detail)

IMG_3074.jpg

 

Right(detail)

IMG_3070.jpg

 

Abdomen (details)

IMG_3080.jpg

 

Action shot

IMG_3078.jpg

 

Cod and Butt Plate

IMG_3081.jpg

 

Interior Strapping

IMG_3082.jpg

IMG_3083.jpg

IMG_3084.jpg

 

Helmet Front

IMG_3085.jpg

 

Helmet Sides

IMG_3088.jpg

IMG_3089.jpg

Helmet Back

IMG_3090.jpg

 

Hovi Detail

IMG_3086.jpg

IMG_3087.jpg

 

Lens color

IMG_3091.jpg

 

Blaster Left

IMG_3092.jpg

 

Blaster Right

IMG_3093.jpg

 

Neck Seal

IMG_3096.jpg

 

Thermal Detonator

IMG_3097.jpg

 

Hoster Attachment

IMG_3098.jpg

 

hand plates

87B1A763-B34D-4AE4-BFDC-6838FC43D0AB.jpg

 

ammo pack (rounded)

246F1A92-2680-4853-AB76-6779F684F498.jpg

 

knee plate alignment

43802884-2FCF-4EE8-AC5C-2ED8AB6EDC01.jpg

 

 

Thank You!

Edited by devilmaan
Link to comment
Share on other sites

Looks good! Only suggestions I have is looks like your left shoulder bell could come in a little bit and close up some of the gap between the back and kindey....

 

Good luck :duim:

  • Like 1
Link to comment
Share on other sites

Thanks and thank you for the suggestions. I did notice that my my elastics over my shoulder bridges weren't pulled over. :-( they are there though

 

 

Sent from my iPhone using Tapatalk

  • Like 1
Link to comment
Share on other sites

Thank you!

Going to make some tighter snaps for the back/kidney piece this weekend. That gap is a tad big.

 

 

Sent from my iPhone using Tapatalk

Link to comment
Share on other sites

Thanks Tony!

 

"For level two certification (if applicable):

•Any gap between the abdomen and kidney armor is no more than 1/2" (12.5mm) wide."

 

Wouldn't this be pertaining to the side gap between the kidney and the ab plate?

 

I agree that the gap between the back plate and the kidney is too large.. but this is something different is it not?

 

Thank you, Terrell I love the Kit!

Edited by devilmaan
Link to comment
Share on other sites

OOPS! My bad I was referring the the kidney and back. WOW huge typo on my part.

 

My apologies 

 

Great looking armor  :jc_doublethumbup:

Edited by ukswrath
Link to comment
Share on other sites

Hello Todd!!! Thank you for this great looking set of ATA and a great looking application. Let's look at you!!!

 

CRL and EIB Application Requirements:

All required submission photos have been posted. Your armor contains all the elements required to obtain the Expert Infantry badge. Congratulations and welcome to EIB!!

 

Other-Armor Fit/Assembly:

Some builds and their results are just a pleasure to look at. This one is no exception. 

Brilliant work on your helmet's painted details and your blaster details. The weathering and silver added to your trigger group area really makes this pop! 

I want to bring this up because it has been a discussed issue in the past. It has to do with the proper widths of the cover strips compared to the raised ridges that are present on TE based armor like ATA. Todd nailed it here. Yes, he needed a little more room in the biceps, calves and thighs so he used the extra material made available to make them fit to his body type. Once properly fit, he capped the seams with the correct width cover strips.post-12041-0-69383600-1435532258_thumb.jpg

Some believe that the raised area, no matter how wide, should have a cover strip to match. I just could never agree with that for two reasons: #1 the size of the cover strips on the original suits. Ours should be the same unless certain circumstances require it. . #2 the raised ridges on TE based armors on the biceps, thigh and calf backs shouldn't even be there so why treat it differently because they are,

Anyway, nice job, Todd!!

 

Centurion Suggestion:

I try to see everything and mention what I can here. Final Centurion accuracy is the responsibility of the trooper.

I hope to see a Centurion application from you. With all the present details you have, I would be really surprised if you didn't.

Usually regarding the space between the back and kidney I comment regarding too much overlap. Rarely do I see too much gap. It sounds like you are already on this so I will wait until your next application to ring it up again.

Congratulations and nice work!! Troop on with pride!

  • Like 1
Link to comment
Share on other sites

Thank you!!! Reading endless build threads and learning from all of the awesome people here helped me so much! Thank you very much!!!!

 

 

Sent from my iPhone using Tapatalk

Link to comment
Share on other sites

  • 2 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
 Share

×
×
  • Create New...