Jump to content

Aren't you a little fat/short for a Storm Trooper - RT-Mod


andylah

Recommended Posts

The time has come for a TK! 

After the awesome advice from everyone on SCG  to get a soft costume and decide whether trooping is for me before getting Armour I’ve decided Trooping is for me and its time for Armour…
 
Lots of research via FSID and SCG and i decided RT-Mod was best suited for the bigger guy, thinking wider, not taller so this may still be hit and miss….
 
 
here goes with list of stuff:
 
TK Suit -  RT Mod - obligatory big brown box photo will go here once it arrives...
17705922253_283a5b09cb_z.jpg
Under suit/Balaclava - Stromtrooper under suit but arrived in Extreme Racing satchel. 
18067959498_245accb4d4_z.jpg
 
Boots  - Dublin Elevation Jodhpur Boots
 18068196360_9dee64ea78_z.jpg
 
           - painting supplies 
18255768305_ec32eea517_z.jpg
 
Gloves -  Ansell Black ones from Woolies
handplates - TrooperBay
17635337873_868a4d7749_z.jpg
 
E-11 - Trooper Bay / Doopy Doos -  here is finished photo… this was a whole lot of fun to build
18068131348_1c145420cf_z.jpg
 
Holster -  still need to source?
 
hardware -  still need to get. - buttons, elastic, webbing etc - this was fun.... walking into Lincraft with no idea what i was doing nor what I needed and just grabbing a shucks ton of stuff
18067951688_bfbc18615a_z.jpg
 
Neck Seal - Trooper Bay 
belt -  Trooper Bay 
18229483476_c2750bfe65_z.jpg
 
TD Clips -  Evilboy
17633342354_ac6ac92c44_z.jpg
 
Bucket Fans -  Evilboy 
18229490816_e35aac9e98_z.jpg
 
Mounting belt thingie -  stealing Drew's idea I grabbed one of the belts https://flic.kr/p/tNSjvN from bunnings that should also act like a girdle a bit i hope.
18252009432_07d7e639dc_z.jpg
 
 
So I started "operation lose a shucks ton of weight" back  when I ordered the Armour, and that worked for a bit but didn’t really happen to well which is the suck (my fault) So  would like to be able to size it down as needed hopefully :S
 
eeeek i'm scared.
 

18257580725_0abbdc2c91_z.jpg
 
My confused look at having no idea what i was doing in Lincraft!
 
 
Day 1 Progress:
 
18339030656_e55e856964_z.jpg
plus
18177649688_0548e7d90a_z.jpg
equals
17742830064_0ca7ff00a1_z.jpg
 
I promptly put the hammer down and grabbed a keyboard and spent all night reading.
 
Still scared shucksless.... suit remains in the box.
Edited by andylah
  • Like 1
Link to comment
Share on other sites

When are you expecting your big brown box?  The RT kit is a dream to work with, seriously.  Rob is a true artist, and the kit reflects that.  It looks like your research is already paying off well, as you've got a lot of necessary bits there waiting for your BBB day!

 

If you have any questions about building that kit, be sure to have a look at the existing RT builds out there already.  You can find my build thread in the link in my signature.  

Link to comment
Share on other sites

Big Brown Box arrived yesterday

17705922253_283a5b09cb_z.jpg

which was madly torn open and this happened

17703959754_0aee2e6752_z.jpg

and thats as far as I got...

 

It then went home and sat resealed back up to make sure I didn't start anything before I was reading.

 

I've just spent hours reading your whole thread @Dark CMF and am in awe and hope mine turns out to be even 1/4 that good...

I have another 5-6 build threads to read up before I start playing i think...

 

im still scared though....

  • Like 2
Link to comment
Share on other sites

Thank you, there are a lot of REALLY helpful build threads that helped me to get started.  Read through every one that you're planning to read, they'll help your comfort level substantially.

Of course, you'll still be scared until you've already assembled at least both biceps and probably one forearm.  

 

Then, you'll just be cutting stuff to pieces like it was nothing.  That first cut syndrome though...  You'll be weakened and nauseous about it until you get it over with.

We all go through it, but we've got your back.  ;)

  • Like 1
Link to comment
Share on other sites

YES ANDY!!! CAN'T WAIT!!!! 

WOOOOOOOOOOO!!!!! Super excited for you. 

 

Just some back story with Andy....when he got his officer approved a few months ago he was out trooping every weekend and even came down to Melbourne for a massive troop. Stayed with me for the night and checked out my TK and he's been hitting me up with questions ever since!

I have no doubt this build will turn out great!

Link to comment
Share on other sites

thanks for kind words people!

 

Hans, i might need a trip to Melbourne :P

Q, i might need a holster :D

 

anyway, progress...

 

 

So after two days of reading and weeing myself i decided to unpack the box

18223910060_462f417755_z.jpg

damn. im scared even more now...

which turned into quick lets put stuff on....

17793267824_f601b3176e_z.jpg

after putting everything on as best as I could reason / work out/ willing to try it fits alright

RT Mod is made for bigger person, me thinking sideways didnt think of tall so im still not sure how tall it all is in reality to me but am sure some trimming will be necessary
Right calf wont close as is, no surprise there so that will need shimming
as will the kidney to ab plate, that will need a chunk of shimming i think, on both sides so that will be fun too....
everything else seemed okay, but when you are trying to hold it together and explain what you mean to blank looking father i am still unsure...

Once I rewrapped everything back up in plastic wrap I moved on to tab making...

18228200600_9fb5a1456f_z.jpg
again without any real plan i just made back tabs which will at least get me some idea what im doing...

game plan I think is start with the arms... forearms up I think...

looked at those bits and thoight okay, i think i know what goes where, and was thinking this looks all very symetrical???

17795246813_18edec7009_z.jpg

so in conclusion, slow progress but any progress is progress....

Link to comment
Share on other sites

I'd suggest you do biceps down, as the forearms are a little more complicated to fit typically. I do always suggest/recommend the biceps first for all TK builds.

Link to comment
Share on other sites

thanks for the advise Tim!

 

so after poor planning on my part I missed the Canberra armour party which was silly. It would have given me th confidence and access to people in the know to have some idea what i am doing...

 

And yes this was taken after the Dubs lost today :( damned Dellavedova locked Curry up....

anyway; finally got to take it out of the box again and started on the arms...

first issue encuntered  - i keep cutting my hose putting the bucket on....
18562350986_e51d1e065a_z.jpg
so step one of armour building, bleed is done...

right arm:
18399267610_39040e8ae2_z.jpg
that felt okay until i did the left arm...

Left arm:
18562361896_ab6b396123_z.jpg
the left bicep goes up a lot higher than the right

both shoulders attached to the biceps, and the left is definitely horter, which leaves  the gap between the forearm better
18402769619_661d1d95d0_z.jpg


Once again, hopeless photographer father takes a bunch of shots and this is the only usable one...
18562359046_e83fdd7497_z.jpg

I think the left is good? the right needs some work, will start with getting rid of the return edge as its not so scary, but it might need some off the top as well...

again:
18562368466_424e052e47_z.jpg

and the forearms might be a tad too long but im really scared of cutting them? both are similar to this...
18562584176_14e68cb8e6_z.jpg

Edited by andylah
Link to comment
Share on other sites

Get rid of most of the return edges of your bicep parts so they can slide up and down a bit.

You'll be a lot more comfy an you don't have to cut the length.

Your wrists look like they could be a little tighter, but that also depends on your comfort level.

Just remember, that the wrists don't have any return edge at all.

 

Oh, and btw, your forearms are way too long.

Compare them to reference photos and you will recognize, that the long part with the square indentions is cut off at the wrist and does not end in a return edge.

 

Looking good so far!

Edited by Bone
Link to comment
Share on other sites

Hi Andy!! Just get stuck into it mate ;)

 

If you need help, just give me a yell. I'm not far away from you :)

Link to comment
Share on other sites

  • 3 weeks later...

So I took a heap of photos at Nova and spoke with lots of people and today was the day I finally got down and dirty and some work....  well I thought I got stuff done, but I really think i just opened new questions...

anyway, progress is progress....

1. painted TD pipe grey. woot... means I shoould just be able to do this tomorrow and have something crossed off the list
2. reset and looked at shins
Left looks okay I think; just glue it and velcro in the rear - shave some off the bottom and even it up?  (who thinks they are too long)
19006302510_4f6c4ea327_z.jpg
and
Right leg is again my issue.... how do I ttach them, after this was taken i realised it might be okay just to velcro in the rear if i space out some more in the front -  but i presume i want symeterical?
19197572351_7b54438cd3_z.jpg
Given RT-Mod uses the overlap method im confused to what I should do really

3. I half glued both biceps after trimming the inside return edge which makes them fit a whole heap better...
yay for magnets
18578021464_08d19d557f_z.jpg

4. Thighs.... again problem area; although this time I think they need cutting more so to fit more snugly - but can't tell as they arent attached yet so might not be such an issue
Left, I think I need to cut at inch plus off the top to make them shorter, which will skew the rest of the fit i think?
19009236879_cf3a948ff3_z.jpg
and right with similar issue  - for these I had my sister tape up the back nice and tight and think I need to again cut some off -  this might sort itself out if i lose some length at the top?
19007736860_e6b3c25dcb_z.jpg


5. forearms... I need to cut at least a 1/2" inch off the wrist to get to just the raised bit, and as such probably similar at the other end... looking at other kits at Nova, everyone seemed different and all of them seemed long? not sure if I want to do 1/4" inch off each and reasses / ask the masses to be sure..

6. finally I installed the evil boy fan kit in my bucket which has made a world of difference...

so that was my Saturday...

Sunday I hope for some strapping, some more snap making, first proper cutting.... also will put on shins/thighs and crotch together and see what happens......

Link to comment
Share on other sites

Sunday has begun and leads to more questions...

 

19032031400_0bf6c828fd_z.jpg

 

left end cap isnt on properly atm, right one is stuck on (not by glue) ive taped on the bits to see if the spacing looks okay??

 

but where does that other bit go??? underneath I assume?

 

I've taped it all up and put on properly and it might be too long?

Crl says approx. 7.5" ATM it's 8" as the one end that's on I can't get off, not sure if I'm meant to over lap it or what?

Not sure that's an actual issue or not?

Edited by andylah
Link to comment
Share on other sites

today concluded with my basically giving up after managing to somehow glue the outside to the inside, not the inside to the outside...
with zapagap.

19219586142_4bded2f575_z.jpg

as shown there, I managed to rip it apart but have ugly glue residue left on the outside of my right shin...

so options:

1.  use tge zapagap debonder stuff as best I can and then buff the hell out of it with the dremel and a polishing head and hope it comes good... (on initial trials the debonder stuff seemed to get rid of the bulk of the residue but left it looking matte.)
2.  just stick a covering strip over the top of the face that shows... (one side of the join will have two edges, the overlap and the cover joint)
3.  abandon overlap method and go with butt joints and strips for all... (can the overlap'd armoue be converted to butt strips relatively easily)

Now each has its merits and negatives.....

nobody to blame but myself... yay me.

Link to comment
Share on other sites

1 seems like a recipe for disaster... 2 would work. 3 may be your best option.  ukswrath has a build thread going for an AM1.0 kit that was meant to be overlap, but he's making it all butt-joined.  Check that out, and see what you think.

Link to comment
Share on other sites

fairly productive day thanks to Chris788 and hansdc in Melbourne for answering countless silly questions!

made the first cuts with the assistance of Clone Wars, some epic strong coffee and Tamiya lexcan scissors... (these things rule)
18775061583_fd3107bf27_z.jpg
Chopped off the ends of the forearms and got them ready for gluing....  ( they need some cleaning up and sanding)
19208087750_2896863154_z.jpg
broke out the e6000 and did some gluing of the forearms and shins
18780026873_58743cf065_z.jpg
and got the TD good to go
19214438729_88c2130c60_z.jpg

So half the forearms are setting now, will look how they are going tomorrow.
Both shins are now glued with velcro in the back so that is a bonus...
TD needed its clips shortened so also did that.

Tomorrow I hope to finish the TD.
Look at the thighs some more and see whats needed there.
look at the chest bits, kidney, ab plates etc etc to see whats next...

good day overall, actually feels like I achieved something...

  • Like 1
Link to comment
Share on other sites

  • 3 weeks later...

So progress is progressing:

 

Shins, forearms and TD are glued and good to go: (other shin is some where else)

19493452696_b791f11c1f_z.jpg

 

just work on fitting the forearms properly and making them a tad shorter possibly still...

 

And the Echo Fan setup I ordered arrived and is in place now.. still need to attach slightly more permanently..

19334319119_3edc3c6c45_z.jpg

I opted for the custom name and numbers which I think adds to the badass level and makes it feel like mine!

19525034951_7a0ba2d565_z.jpg

 

Now the helmet feels really small; have to pay attention putting it on and pulling off with fans; but I haven't tried with the balaclava on.... (that will solve the beard getting sucked into the fan problem at least)

 

Weekend is looking at thighs and running away, hopefully painting the ab buttons, and I think looking at the belt to try and get that progressing although I have missed buying a holster.... whats a good holster????


 

--------------

 

epic troop on Saturday helping out and I managed to get another good look at some TK kits and progress was had..

 

First go round at painting dots -  the cd label stickers I had weren't quite right so I free handed them, i did them again and they look better

19649025192_ae02eb508a_z.jpg

Second go:

19739291055_4747e5672e_z.jpg

 

Armbourboy big an impolite person storage box arrived

19544733710_2e14818828_z.jpg

 

Then on to the belt:

Some rivet goodness - 1/8" from bunnings

19195597214_a22a52201f_z.jpg

Then some push buttons. Feeling more confident with these now, ready to start strapping soon too i think

19792038416_e56026cc23_z.jpg

both done, woot.

19197651963_d49be7f771_z.jpg

 

and almost done - still have to stick the cover buttons on, and work out if the flappy bits at the ends are too long. Left it warmed up around a bike tyre to get some good curve happening

19630550928_8708cda9c7_z.jpg

 

Next step is connecting the drop boxes and looping with elastic over belt, and attach the still hasnt been purchased holster....

 

New found motivation tonight I want to hit the sniper plate, and the should straps I think; and hopefully look at the beginning of strapping to try and get some of the body fitted up.

Link to comment
Share on other sites

Is the body harness going to act as a garter aswell? If so that's a great idea I may steal.

yeah that is the plan... and a girdle, suck gut in, push this out, and then also give me (in theory) a fixed point to strap thighs too....

Link to comment
Share on other sites

so with a anew self imposed threat / goal in my head I got into it tonight and achieved nothing really lol

Ab buttons are french blue
19885247966_68824e7882_z.jpg

arbitrarily stuck the shoulder straps on just to have a look see
19903931162_9504b04cd3_z.jpg
which lead to taping armour to me to see whats what...
19916554801_d76c134d64_z.jpg
take away points. my torso is really short, so need to hack and slash some length off the lot... and the cod piece is a separate piece to abs? is that normal @chris seemed to think it was odd...  (would top of cod be logical place to shave some space) -  RT Mod has a line drawn over it that says belt line so maybe not? in which case do I cut the bottom of the abs off to the bottom of the chest... actually proper scared about that now....

finally moved on to thighs... my previous guestimate was close, but I loosened a bit given comments by others and they feel much better... ive taped/magetneted and clamped them up overnight to try and get some shape out of them as they dont feel the right shape... hopefully then I can glue the fronts and make proper adjustments to the sizing and possibly shave some more height from the tops... (I need to even out the backs as its lopsided and has a edge that sticks out
right front:
19290538583_146f01045e_z.jpg
right back (excuse half undone shin, photographer didnt mention until after and I couldn't see it
19723454148_bf78ced829_z.jpg
left front
19288848714_5219e82da0_z.jpg
left back
19723440358_19f2eb963c_z.jpg


so again what I hoped would be a productive night has turned meh once I have reviewed the photos again....

Link to comment
Share on other sites

after moving forward and then two steps back I reread Dark CMF's build and

 

this looks much better
19313749204_8da2353b24_z.jpg

stuck the cod piece up behind the abs
19941510511_4e5b193928_z.jpg
19936387535_5f26532d06_z.jpg

still just temporary but a relief none the less

 

then

some more gluing last night got me excited again:
Sniper Plate
19779143469_aff7b1a187_z.jpg

and  fronts of both of the thighs
19779150199_f6eccf4b80_z.jpg

Edited by andylah
Link to comment
Share on other sites

  • 2 weeks later...
began the weekend again with lots of motivation.... ended the weekend in a alcohol induced paralytic state that stopped all my good intentions...

started with me doing the linc.

20157564802_608d230d00_z.jpg

 

Boots have like 7 coats of white on them and look good... ( i peeled off the tape off the soles shortly after this pic was taken)

19566430343_71ddd41ecb_z.jpg

 

Did some more trial fitting with the aim of getting cod piece attached to Ab plate...

20139404706_a5c240a23b_z.jpg

 

hand plates suck. these suckas just dont want to glue on properly -  do i want to glue them on to the dish washing gloves given they suck to troop in?

20000796919_5057e49e4c_z.jpg

 

Now the elephant in the room.... Shims. Do I need them or not... when i got test dressed up and had dad measure them i need 7.5 cm shims to join the ab and kidney plates. When i got properly dressed and threw the belt on it was 4.5cm... In theory I will build them like that temporarily to see what is needed... reading the rules I might not need too? My stupid brain wants me to close the gaps and i would prefer them?

20171266031_ec09278803_z.jpg

 

gave up moved on to the belt...

20000829439_8b9187ffa6_z.jpg

all riveted together now, just need to lop off the edges and cut the 45 degree angles and then attach the holster... good times.

 

ended the day with attaching some of the snap buttons to the ab plate to try and get it attached... my plan was to haev all plates built and ready for gluing this week after work... that didnt happen...
  • Like 1
Link to comment
Share on other sites

getting excited now and I don't think i'm actually scared any more... well within reason

 

20330761972_3022dcbb13_z.jpg

 

belt attached and tight for once and the abs are snapped to the cod piece.

 

20373408461_68a780efe3_z.jpg

internal snaps to attach cod / ab plate... the one of the left likes to twist a bit as it doesnt seem to fit flush.... i lowered the ab down a bit to make it fit better...

 

19746034523_d2d3b1c45b_z.jpg

 

snaps and elastic for the shoulder bells... not sure I like this as I think the snaps will run, but easy to rip out if needed...

 

 

next steps:

 

1. belt... finish it off -  cut the edges off (i think at the tape line) cut the 45 degree angle and attach the buttons. I really want to make one of the boxes usable but cant think how easily

1a. add the Gazmosis holster to the belt.

2. cod snaps and rivet

3. look at back pieces to start lining them up to work out the chest piece to work out if i need shims in ab plate and how high the chest needs to be

4. velcro/elastic/snap combo to attach to the weight belt thing I have... in theory its snaps to some elastic  with a length of velco as high as the belt so they are always in a fixed position

 

I can see reaching a point of needing actual assistance for decent fitting and final cuts before doing approval stuff soon... I cant seem to get any of the family to actually take the photo i want/need...

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...