Jump to content

TK 62280 Requesting ANH Stunt EIB Status [ATA][319]


Recommended Posts

Name: Jeff Young

TK ID: 62280

Garrison: Wisconsin Garrison

FISD ID: grishnock

 

Armor: ATA

Helmet: ATA

Blaster: Hyperfirm

Height: 6'2

Weight: 190lbs

Boots: TK Boots

Neck Seal: Trooperbay

Holster: Trooperbay

 

907240_10200754975384279_291434824_n_zps909360_10200754975304277_1763133134_n_zp912107_10200754975344278_575753560_n_zps907397_10200780684706996_568449665_n_zps913258_10200754975184274_702007764_n_zps913155_10200780684666995_1383644219_n_zpDSC_0131_zpsd8c16ab4.jpgDSC_0130_zps5dbf96ba.jpgDSC_0127_zps6b0bd4c0.jpgDSC_0123_zpse60656e1.jpgDSC_0122_zpsda65300e.jpgDSC_0121_zpsf229c0a3.jpgDSC_0114_zps26177de4.jpgDSC_0118_zps8684d3e2.jpgDSC_0116_zps401e0802.jpgDSC_0115_zpsfc11f4d3.jpgDSC_0119_zps3c16012a.jpgDSC_0120_zps994e7a05.jpgDSC_0096_zps17629fd6.jpgDSC_0094_zps31cc1a8f.jpgDSC_0093_zpsaa0057f7.jpgDSC_0070_zps0f6d883d.jpgDSC_0128_zpse2cb58f4.jpgtest_zpsd568a680.jpg

Link to comment
Share on other sites

I've spotted a few painting issues for consideration.

 

1. Your helmet grey frown.

There is no paint after the 4th tooth onto where the 5th tooth would be.

Therefore the helmet appears as a hero

Helmet.

 

2. The AB plate buttons appear to be the old dark midnight blue rather than the helmet tube stripes French blue.

 

As initially mentioned, these points are merely raised for consideration / discussion.

Link to comment
Share on other sites

I've spotted a few painting issues for consideration.

 

1. Your helmet grey frown.

There is no paint after the 4th tooth onto where the 5th tooth would be.

Therefore the helmet appears as a hero

Helmet.

 

2. The AB plate buttons appear to be the old dark midnight blue rather than the helmet tube stripes French blue.

 

As initially mentioned, these points are merely raised for consideration / discussion.

Both valid points, and both easy fixes.

Link to comment
Share on other sites

excellent built there, one thing I would recommend to do is raise your belt to just under the ab button plate. I use snaps to hold mine in place.

Link to comment
Share on other sites

Hi Trooper- nice job on your ATA build!  I wanted to pass on a piece of advice that I received on my ATA EIB build, and that was to decrease the size of your forearms so they aren't as big/ loose on your body.  I was really pleased with how it turned out when I made this adjustment, and I think it could look good on your build too.

 

Again, nice job and good look on earning your EIB!

Link to comment
Share on other sites

  • 2 weeks later...
  • 2 weeks later...

The belt was an issue for me too. I finally just put snaps on either side of my ab to hold it up.

 

Good luck! I just updated my approval post as well, another tall ATA here too!

Link to comment
Share on other sites

  • 3 weeks later...

The missing ear stripe from the helmet pictures, that appears on the full body pictures leaves me quite confused as to whether you have it or not. But you should have it on the last bump if you haven't added it already.

 

And as mentioned, your belt is still sitting too low on the ab, but I take it that because of your cut cod that there is nothing you can do to correct that any more.

 

But for the intents and purposes of EIB, you are approved! :duim:

 

You will however also have to post an action photo for our EIB page.

Link to comment
Share on other sites

The missing ear stripe from the helmet pictures, that appears on the full body pictures leaves me quite confused as to whether you have it or not. But you should have it on the last bump if you haven't added it already.

 

And as mentioned, your belt is still sitting too low on the ab, but I take it that because of your cut cod that there is nothing you can do to correct that any more.

 

But for the intents and purposes of EIB, you are approved! :duim:

 

You will however also have to post an action photo for our EIB page.

 

I actually did the paint job for the ear bump after the initial pictures were taken, I was looking into getting it ready for centurion. Im reworking straps to raise the cod piece up to fix the belt problem. I should have it fixed before I try for centurion. Thanks for the approval man! I'll throw the armor on and take a pic for ya on one of my upcoming days off.

Edited by Grishnock
Link to comment
Share on other sites

  • 4 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
 Share

×
×
  • Create New...