Jump to content

Recommended Posts

  • 3 weeks later...

Wow, looks like a very good job on chroming these parts. :duim:

 

And the eyes in the last picture look so real :shok:. Fantastic!

 

Will you add some weathering later?

Link to comment
Share on other sites

Holy movie perfect. However, you listed this thread in the other 501st costume section. 3PO clearly is not 501st thus a clear violation of forum rules. I will send you my address so you can relinquish the costume to me as punishment. You did spectacular work! I will thoroughly enjoy the costume!! ;)

  • Like 1
Link to comment
Share on other sites

  • 3 months later...

Hey everyone! Sorry I have been so absent. School has been doing it's best to kill me for the last year.

 

 

That looks FANTASTIC!  Can you give me any detail on the chromed paint?

I had the whole suit sanded by an automotive shop ( I could have done it myself but it would have taken many more hours than what it took them) and then shipped it off to Canada (http://www.vacuummetallizing.ca/index.html)

 

Without further ado, some updated pics for you all:

 

Hands

10881762_10204499909716358_4731189121700

 

Sizing the belly mat

10394056_10204534024169198_7264564640072

 

Decorating the belly mat

10540626_10204534562662660_4919345430066

 

Dead body in my living room

10411304_10204534746067245_5892374530556

 

Trying some things on

10914934_10204566775747967_2242185252402

 

10344303_10204566775907971_1448932661799

10872781_10204566776667990_3344474927386

10460861_10204566776947997_4199957678528

 

 

And some Abrams effect:

1557222_10204566775267955_34371893054058

 

The plan is for a more complete suit up this weekend. During this session of trying things on I figured out the belly mat was too small so I have remade it. You'll also note that I'm missing 2 finger tips...no idea where they went to so I am working on getting those replaced. The helmet was finished off today so it actually stays closed now. I will try to remember to upload the finished pictures or whatever shots we take this weekend. 

Edited by HockeyTrooper
  • Like 3
Link to comment
Share on other sites

Almost completely finished, here are some more pics from today. My buddy's R2 isn't completely finished yet either.

dwOfLdd.jpg

e7nEaEH.jpg

 

zW3JmLF.jpg

 

Also made a facebook page for the droid! https://www.facebook.com/pages/KC-3PO/917322388313043?ref=aymt_homepage_panel

  • Like 2
Link to comment
Share on other sites

Thank you all for the high regards!

 

Gazmosis, PM replied to! 

 

JohnnyChaos, astromech.net is the R2 builders group. I don't know much about them but from what I have heard they aren't sold as kits. Instead there are patterns and parts available for purchase or use to assemble and cut pieces from wood or styrene, or for those going for a heavy duty build using aluminum parts from runs that occur periodically.

 

As for mine, I've gotten enough comments on the belly that I will probably increase the amount of wiring before I submit photos and make my neck piece slightly larger.

 

Also, gotta grab a nice pair of these to make up for the very slight gap in the sides of the shorts.

 

You enjoyed clicking that link a little too much.

  • Like 2
Link to comment
Share on other sites

 

Also, gotta grab a nice pair of these to make up for the very slight gap in the sides of the shorts.

 

You enjoyed clicking that link a little too much.

 

Can't. Stop. Laughing.

 

-Eric

Link to comment
Share on other sites

Unfortunately there isn't any video yet. The person who took video was using snapchat to send to her friends but forgot to download them to her phone. As I get more pictures at events and such I will post more! I'm still missing 2 finger tips preventing me from doing submission photos

Link to comment
Share on other sites

Thank you all for the high regards!

 

Gazmosis, PM replied to! 

 

JohnnyChaos, astromech.net is the R2 builders group. I don't know much about them but from what I have heard they aren't sold as kits. Instead there are patterns and parts available for purchase or use to assemble and cut pieces from wood or styrene, or for those going for a heavy duty build using aluminum parts from runs that occur periodically.

 

As for mine, I've gotten enough comments on the belly that I will probably increase the amount of wiring before I submit photos and make my neck piece slightly larger.

 

Also, gotta grab a nice pair of these to make up for the very slight gap in the sides of the shorts.

 

You enjoyed clicking that link a little too much.

 

OH MY EYES !!! ... MY EYES ARE BURNING... !!   :blink:  :laugh1:

  • Like 2
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...