Jump to content

Ducati's Build


Ducati

Recommended Posts

First off, I like to thank everyone on the forums for all of your help. This build would not have been possible with out you. I am very grateful for everyone that has made a build thread, answered my questions or done a tutorial of some type. I stand on the shoulders of giants.

I started my build last November doing research, modelling and drawings. Fabrication started just before Christmas. Today I've finished. I've done my best to take photos along the way (just over a 1000pics) but looking back I realize that I've missed a few steps. If I were to take a guess I'd say I've put nearly 1000 hours into this project. I've learned a tonne and enjoyed every minute of it. Everything that you will see, with a few small exceptions, I've built myself and I'm very proud of the results.

Please note that I have purposely done some things that are not 100% screen accurate. The reason for these variations are typically for the ease of fabrication or I wanted something a little cooler. If you're a purist you may want to turn back now :) .

 

Anyhow, here is the first set of pics detailing the butt cap construction.

Turning the raw mat

8125999584_a6aeb3cf65.jpg

Starting the bore

8125975533_0b4c6b75b7.jpg

An hour later the bore is done

8125999172_ae6120692a.jpg

Doing the taper

8125973297_5befe1060e.jpg

Out of the lathe and into the dividing head for a slot cut and some milled flats

8125974637_d15fdeb552.jpg

8125974499_79fbe90b6d.jpg

8125974435_2a24e11b96.jpg

Out of the dividing head to the band saw where I removed the extra part for holding. Then back into the mill to clean it up.

8125998094_7a21de27e1.jpg

Here I need to skip ahead a bit. I made some tabs (more on how later) I've bent then and then had them welded onto the butt cap.

8125978017_b7b3aa01a7.jpg

Some filing and then filling with a 2 part epoxy.

8125977519_39372a16fc.jpg

A bunch more sanding and it was off to priming with an aluminum specific primer.

8125976927_6df3e8d06c.jpg

Finally a coat of hammered black then flat black.

8126000368_82725133c1.jpg

I'm out of time for today. I'll post more later.

 

CNC files:

PDFs_and_edwg.zip

Scope sight.dwg.zip

Edited by Locitus
Link to comment
Share on other sites

  • Replies 107
  • Created
  • Last Reply

Top Posters In This Topic

Post #2 D-Ring holder and the D-ring.

 

The original D-Ring holder looks like it was punched out of sheet metal then stamped to shape. Making a set of dies to do that was not practical so I ended up machining this part. It started with a piece of plastic which I turned to the appropriate diameter. Then it went into the mill to machine the "bends" in the sheet metal.

 

8125998976_cd56b402f2.jpg

 

8125974983_2dfcb6c6c8.jpg

 

Next was to flip the part over and clean up the bottom. Then I milled the rest of the "bends".

 

8125974883_c797dce654.jpg

 

A test fit on the cap.

 

8125997832_875027248a.jpg

 

Then off to paint.

 

8125973669_0c6c1cc51b.jpg

 

The D-Ring. This is a case that I didn't take photos of how it made it. It was actually one of the more problematic parts. I tried bending round bar to shape but I didn't have much success with either steel or Aluminum. I ended up machining a "donut" out of flat bar then filing the edges round.

 

8125997730_b7c7bf1cd7.jpg

 

A dab of glue.

 

8125976229_075e39fcf3.jpg

 

Finally some weathering. Note I did a bit more after the final assembly of the entire prop. What I did here was some light stuff to make the edges pop.

 

8125975975_10f901927c.jpg

Edited by Ducati
Link to comment
Share on other sites

On to the counter.

 

This was really the first item I dug into on the build. The learning process on these parts was tough. Before starting on this process I'd never machined anything before and as a result everything took a long time. I was unsure on everything from the feed rates to the order of operations on each part. The thing that really shocked me is how hard it is to machine small parts on full sized equipment. Its so easy to wreck a detailed part; you can hold it too tight in the vise and distort it or you can not hold it tight enough and then the cutter can do bad things. The smallest miscalculation and you'd be swearing as 8 hours of machining was in the toilet. This realization actually made me stop part way through the process and redesign how the over all assembly would be done. Instead of having a series of small plates that I would glue together, I chose to make the plates as large as I could and machine the detail parts into the large plates. I also made the decision that anything thinner than 1/16" (1.5mm) was gong to have to be made a on something other than a mill. Again more on that later.

 

First up a bit of a better explanation of how every part was done. So I start off by working in a modelling program called Solidworks. Its the go to design program for manufacturing. I use this software every day in my real job. By modelling this prop up before hand you can plan everything out to ensure that everything will fit together correctly. Its a lot of work do but its a lot less work than making 3 parts because the first 2 don't work. But the thing I like the best is that you get to work with quantitative figures; plate "A" is 3.0625" long.

 

Below is the process from start to finish for one part:

 

The finished model of the counter:

 

8135801683_39cef302f9.jpg

 

Just the top plate model

 

8135829960_53af644531.jpg

 

From the model of the individual parts I made drawings for manufacturing. Typically these are a bit more professional but since these are for my personal use I'm a little sloppy with standards.

 

8135801569_9de4b2f089.jpg

 

From there I grabbed a chunk of aluminum from the scrap bin

 

8135483358_001468440f.jpg

 

Then to the band saw where I trim the material to a rough size. Taking a bunch of material is easier with the saw vs the mill

 

8135454737_bf756cdaa5.jpg

 

8135456370_3ac69d8974.jpg

 

Next I stick the part in the mill and through a series of steps take the rough material to the overall size of the finished part. I'm also making all the sides square to each other.

 

8135453289_0a1010e83d.jpg

 

8135483148_71aeb79b10.jpg

 

Drilling a hole on the top

 

8135483016_7d40c404f3.jpg

 

Then counter sinking it

 

8135482894_f3ea908062.jpg

 

Now into milling some of the details in

 

8135454259_3ab4e6025f.jpg

 

8135482696_03ccfa577e.jpg

 

Then the part is turned so I can do some detail on the sides

 

8135482612_1111f05764.jpg

 

Another turn and I start to clean up the back side. This stuff won't ever been seen but it was important so that the whole assembly could fit together.

 

8135481590_ac4882cb8c.jpg

 

After a bunch of additional work on the back its another couple of turns for the sides.

 

8135481418_a68eb897cf.jpg

 

After that I would go in and sand the part down to remove the machining marks, burrs and flashing. Sorry no picks of that. I don't have a pick of this part finished on its own. I'll show the finished goods off in a later post where you see the rest of the counter parts.

Edited by Ducati
Link to comment
Share on other sites

The counter back plate.

 

Raw material

 

8135450591_c15d9e2d77.jpg

 

Detail on the front edge

 

8135478368_28d5f65b27.jpg

 

A flip and onto detail on the other side. This is a case of where I deviate from the original screen used item for reasons you will see later on. No one will be able to see it so don't think it matters anyways.

 

8135478106_a2e3103d1f.jpg

 

Another hole, this time for wiring

 

8135449465_a959057177.jpg

 

Another couple of flips to trim the sides

 

8135477436_cfbf229650.jpg

 

This pic was done much later in the build. Some holes for sound

 

8135445393_d1d13df72b.jpg

 

8135445053_17832e751e.jpg

Edited by Ducati
Link to comment
Share on other sites

The counter bottom plate:

 

This part is almost a mirror of the top plate but with an extra hole for mounting. Again different than the screen used item but it needed to be done to ensure stuff stayed together properly. To give you an idea of how long it was taking me, from start to finish this part took about 6 hours.

 

Raw mat

 

8135452509_0707c5d695.jpg

 

Trimmed down

 

8135452433_bb079eded0.jpg

 

Detail work on the top side

 

8135452329_1c666e8aa8.jpg

 

Detail on the bottom side

 

8135480716_2e11edaa2b.jpg

 

8135452157_84827a69c3.jpg

 

Work on the left

 

8135480522_3c32edfb0b.jpg

 

Work on the right/ the finished part

 

8135480440_eebee93920.jpg

Edited by Ducati
Link to comment
Share on other sites

The front plate.

 

Similar to the back plate but with the detail required on something seen all the time.

 

Wookie arms!

 

8135456903_146be76cd0.jpg

 

Some trimming

 

8135485392_1dc5aafc54.jpg

 

A very recognizable feature

 

8135485298_64ecb8427f.jpg

 

Notches at the back of the plate

 

8135456537_d095ab3a14.jpg

 

Taking a layer off of the part on the right of the pic below

 

8135456257_edb2bbe711.jpg

 

This is a blurry pic but adding more depth to the edges

 

8135456125_30ee10eba4.jpg

 

Work on the interior side of the box

 

8135456005_fde03c9558.jpg

 

The finished part

 

8135455733_55f56acc75.jpg

 

8135455873_6a03d0a760.jpg

Link to comment
Share on other sites

Hengstler counter plug and a couple of other detail parts.

 

To make this part I had to use a new piece of equipment. Its basically a vise that lets you tilt the part and cut angles. A neat bit of equipment but as with everything a challenge to figure on the first time around.

 

8135479636_217e5a54eb.jpg

 

8135479398_d63ae0f871.jpg

 

My hands are big, but not that big. Tiny parts are tiny.

 

8135479284_5714ffc842.jpg

 

Back onto the lathe to make some simple round stuff. At this point I was getting really comfortable on the lathe. It only took 15mins per cylinder.

 

8135460831_9bbf2aba7a.jpg

 

8135458763_33ee2fee15.jpg

 

8135486272_9b0a5646e2.jpg

 

How the parts go together

 

8135479184_979f186da8.jpg

 

Now on to the spacers between the cylinders.

 

8135433643_0365da8a6b.jpg

 

8135461146_66e3c9c61e.jpg

 

Flip the piece over and cut away the stuff I don't need.

 

8135432031_096d464cfd.jpg

 

8135459918_4ed913473a.jpg

 

I'll show how these parts go together in a couple of posts

Link to comment
Share on other sites

Some machined sheet metal parts.

 

As I stated a few posts back, something made me change my mind on how I was going to make parts 1/16" or thinner. These parts is what did it. Thin stuff is too hard to hold in the vise. When you try and clamp something it just folds. When you can hold it, the challenge becomes how quickly you can cut material off. I found if I tried to take more than the thickness of a piece of paper per pass the parts would bend. This was a very frustrating process.

 

The raw material> I had to bolt the stuff to a jig to machine it down

 

8135457479_0c8bbfc319.jpg

 

its now the right thickness

 

8135485854_f93a098d02.jpg

 

Now cut to length

 

8135456454_6a7c00ba80.jpg

 

And the finished part

 

8135485664_e6c2a758ae.jpg

 

Believe it or not, these 3 parts took me nearly 6 hours. There were too many failed attempts before these.

 

So the last part was the bracket to hold the counter to the scope rail. I'll get into the process on how this was cut in a couple of posts. Once I had it cut I bent it with something called a break press.

 

8135466286_9228dc71c7.jpg

 

8135437219_3408abf222.jpg

 

8135465392_9fe2122505.jpg

 

8135465144_29360ae903.jpg

 

And the final part

 

8135464686_ca3a349fb9.jpg

Link to comment
Share on other sites

Woot! Onto assembly.

 

If you're confused on how all the above stuff fits together this is the post that will make all clear. The last few post represents weeks worth of work. Its one of those it looks easier that it is kind of things. To glue things together I decided to go with a two part metal epoxy; JB weld. JB works fairly well, but I found that it took too long to cure and while it was curing it tended to drip places that I didn't want it to go. This was part of the leaning process of doing something new. I eventually ended up switching to a few different products to stick stuff together, but this is what I used on these parts.

 

8135444033_5b77345c6a.jpg

 

8135444689_d53189cb8c.jpg

 

I actually ended up making a jig to aid with clamping. That what the white thing is.

 

8135443569_44583bed47.jpg

 

Clamp it all up and wait 24 hours.

 

8135471330_9798a22668.jpg

 

8135442479_6bdc81e61c.jpg

 

A day later with the glue dry I had one half of my counter

 

8135441005_85d41de7d9.jpg

 

Now I repeated the process with the other "half"

 

8135468990_13bb7d909a.jpg

 

24 hours later there were some cracks in the seams where to part met. I ended up filling it with JB weld. I found this process to be the worst way to do it. I came up with another method that I used for joining the mag well to the barrel, but I get to that later.

 

8135468058_b6b4c1d2fe.jpg

 

The two halves with some of the plug parts and a few other bits that I didn't take pictures of

 

8135467562_2c1b0150fb.jpg

 

8135438529_c5c7d472f9.jpg

 

Fitting in the cylinder spacers shown in an earlier post

 

8135430947_054be7e3fe.jpg

 

8135458882_932df40ce5.jpg

 

Attaching the bracket to hold everything to the scope rail.

 

8135434999_1b0b09d29e.jpg

 

Finally off to priming/painting. Priming always the part of the process that really stokes me as it makes everything look like the solidworks model.

 

8135429663_f325e2672c.jpg

 

8135458558_9ef37df5a6.jpg

 

And with a coat of semi gloss black

 

8135457894_efc8f55857.jpg

 

8135428775_4e050e03a2.jpg

 

All put together minus the weathering and the goodies that go inside.

 

8135428463_11e8015e4b.jpg

 

8135456736_2f8bb4b32b.jpg

 

8135427735_ac818b499a.jpg

 

Well that's enough for today. I'm almost at my limit on Flickr before I have to play for uploading pics. I guess my wife is going to have to create an account now :)

Link to comment
Share on other sites

Lasers and Sheet metal.

 

The laser cutter

Blasterbuild05-09-12001.jpg

 

After my frustrating experience described a few posts back, I made the decision to laser cut all my sheet metal parts. Laser cutting is what it sounds like it is; a big an impolite person machine that can cut sheet metal up to 1/2" thick. I don't have a laser cutter but I know some people that do. Its a local business that supplies laser cut stuff for my employer. The also happen to do a bunch of stuff for the movie industry. The most recognizable thing that I know of that they have built is Professor X's door from X-men.

 

BlasterBuild07-31-12002.jpg

 

The advantage of laser cutting is that its super precise and quick. The disadvantage is the cost. My involvement in this process is pretty simple since I modeled everything already. I needed export the solidworks models into a program that the laser cutter can process. This is case I ended up working in AutoCAD. I had to sort the parts by thickness and lay them out in a pattern such that I'm getting maximum usage of the material. The laser cutting people then plug my layout into there machine and we get this: (warning this is a pretty big video). If you watch to the end of the video you will see what is getting cut.

 

VIDEO OF LASER CUTTING:

 

http://s1324.beta.ph...-12007.mp4.html

 

At the end of the day I end up with this a perfectly cut parts that I just punch out then form/weld/glue/paint.

 

BlasterBuild07-31-12003.jpg

 

Blasterbuild05-10-12001.jpg

 

Blasterbuild05-10-12002.jpg

Edited by Ducati
Link to comment
Share on other sites

Wow amazing work!

 

I cannot fathom the skill needed for this (neat toys you have to help though!)

 

I wimped out and bought a sterling parts kit, real hengstler, and real M38 to make my display blaster. And I still had issues getting it all put back together. there is no way in the world I could make it all from scratch and then assemble it!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

×
×
  • Create New...