Doggydoc

I bought stencil templates from trooperbay and they worked great.

Congrats

Great job on the ears. It really is a tedious task and not having a deemed would make it even tougher. Keep up the good work. It seems things are starting to get better for you and you are getting more comfortable with the build. ‘’also love the cat tree? Helmet stand”

Is this the right way to put the neck seal on or is it upside down (I tend to like to put things on upside down apparently).

I went with 2. From what I understand it is more for a backup so you don’t have a strap failure.

Having just done the snaps on my AP set that I am building, there is definitely a learning curve to setting them. As many have recommended, I bought the Tandy snaps as you want quality ones to make sure they hold. I got the 100 pack and likely wasted 10 to 15 when I started with mistakes in setting them, there are lots of videos that show you how. From my experience, don’t hit the snap setting tool too hard as it will bend the snap post and offset the 2 pieces. Make sure you are on a solid surface. I used my garage or basement floor which is concrete. The circular motion with the setting tool is essential to get the snap post to flare out evenly. Just go slow with the hammering. justjoseph has a great resource in the all in one TK Index as Glen and Mario pointed out above.

Have my helmet painted to Mr No Stripes CRL now. LOL I beefed up the vocoder as recommended by @CableGuy to give it more of the stunt look. How are the teeth and gums? Any corrections I need to make if I am going for centurion?

Congrats. Well deserved awards.

I think I figured it out. I believe it was a mixing issue. The store I bought it from is no longer carrying Humbrol paints, actually I think that Humbrol is no longer supplying in Canada unfortunately. As a result I suspect the paint sat on the shelf for a very long time and had settled excessively. Dropping a few ball bearings into the can and shaking for 10 minutes seems to have fixed the issue.

Got a bit more of the strapping completed. one question about the butt plate. Should the edges be even with the back of the notch in the kidney plate? Mine are a little bit longer as you can see in the side shot. Should I trim them back to make the edge line up with the kidney plate notch?

Yes. It is the #5. I stirred it for a few minutes with a toothpick. Could it be because yours is going onto white paint and mine onto very shiny abs? couls also be the brush but the black went on thick. maybe I will drop a few ball bearings into the container at shake better?

Started the first coat of the grey. The Humbrol paints really go on thin. Guess it will need several coats.

Thanks Dan. That is the look I am going for. I will raise them up. I actually have been using your references for this. Thanks for doing the videos. They are all very helpful.

Actually it is on a guitar stand.

Started painting the helmet tonight. Will clean up the edges a bit once dry with a toothpick and alcohol and work on the grey tomorrow. I used a filbert brush with the rounded tip and a chisel shaped tip brush for the tears and traps. Worked well.

One thing that I did notice with the AP kit for anyone making one is that if you follow the guide marks for the ear screws and bolt to attach the face to the cap, the ear screws will be up and down and not angled along the rear of the trap line. This could affect centurion level certification

I did the ears this afternoon. That was a long 4 hours of sanding but I am pretty happy with the result. Had some trouble attaching the right ear as the face piece was not long enough to grab it and the back with the bottom screw. I added a small piece of scrap ABS and extended it to catch the screw. I noticed the right ear was a bit loose. I tightened the screw and it snugged nicely into the helmet.

Made a bunch of snaps today and started gluing to the kidney plate. Took a few try’s to get the technique down. The little circle tapping really makes a difference in how hard you strike the snap tool and how much you angle.

Did a bit more work on the helmet last night. Does the brow height look ok? Rough trimmed the ears and also countersunk the holes. Glad I ordered 2 sets as I forgot that you countersink holding the bit in your hand. Makes a pretty big hole when it’s on the drill. Oops

Thanks for all the info. Very helpful. I think I am going to take a pause on the thighs and work on the torso, so I can see exactly where the thighs will sit at the top. Maybe they will be easier to size then.

I am trying to size my thigh pieces and am having a bit of trouble as I have fairly big thighs. the AP set has raised ridges on the front for the cover strips and none on the back. I need to leave most of the ridge on the front to allow my upper thigh to fit into it. Questions: 1) Here is the front view with a 20 mm cover strip placed on the raised ridge. I suspect that I need a wider cover strip? , or do I just leave the outside edges of the raised ridge exposed? 2). On the back side, I have a 35 mm cover strip which I need to cover a gap at the top of the thigh and the guide line from the molding which I did not cut back to to allow for extra circumference. Is this Ok, or is there another solution? on the last photo, there is some return edge that I will cut away on the back side at the top.

Pretty easy fix. Just filed and sanded a bit deeper into the corners.

Thanks. I will alter that. Was more focused with the amount I took out on the eyes and missed the sharpness of the corners.

Had another run at trimming and sanding all of the torso and leg parts. And cut out the teeth and eyes on the face. Please let me know if there is anything I need to fix on the teeth or eyes before I start assembling the helmet. Thanks.

Guess what I worked on tonight? I guess you need to become a snowman before you become a stormtrooper.