-
Posts
12 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Articles
Media Demo
Posts posted by Matt Certain
-
-
Updated photos - cleaned up the frown. Thank you for looking and the recommendations.
- 1
-
Oops- I think I had an older photo list. Will get the rest
- 1
-
Armor purchased from ATA
Helmet also from ATA
Blaster 3d printed by myself
https://www.whitearmor.net/forum/topic/51017-a-certaintk-ata-anh-stunt-build-first-build/
TK 96119 Diamond Garrison
Matthew Certain
6'2" 220 LBS
Boots by ImperialBoots
Canvas belt by TrooperBay
Hand guard by TrooperBay
Holster by DarmansProps
Armor Photos
1.Full Body Front
2.Full Body Back
3. Full Left
4. Full Right
5. Left Side Detail
6. Right Side Detail
7. Action shot
Armor Details
8. ___ Abdomen button plates (close-up)
9. ___ Cod and posterior plate connections showing rivet/snaps (exterior)
10. ___ Interior strapping
11. ___ Wrist openings (close-up)
12. ___ Close-up of ab/kidney rivets
13. ___ "Han" snap
14. ___ Left sniper knee plate close up
15. ___ Right sniper knee plate close up
16. ___ Left thigh ammo pack rivet close up
17. ___ Right thigh ammo pack rivet close up
Helmet Detail Photos (UPDATED PHOTOS)
18. ___ Front
19. ___ Left side
20. ___ Right side
21. ___ Rear
22. ___ Back-lit shot showing lens color
Lens color (Backlit if necessary)
23. ___ Close-up of Hovi tips
Hovi tip detail
Accessory Photos
24. ___ Neck seal
25. ___ TD (Thermal Detonator) front
26. ___ TD Rear, showing close up of screw type.
27. ___ Holster attachment
28. ___ ABS/canvas belt (rear)
29. ___ Boots (showing tops and sides)
30. ___ Rubber gloves
Blaster left side
Blaster right side
-
-
My armor was accepted by my GML . I now have my TK# and am a part of the Diamond Garrison. I am going to try an move forward and get my armor reviewed for expert Infantryman.
Thanks again to everyone here who commented.
- 4
-
Added some additional strapping inside, I think it is helping quite a bit:
after new elastic added inside:
- 1
-
I am using the older style elastic with the brackets - I might swap these out for either stronger elastic or nylon straps with snaps. That way they will stay in position and the shoulder or lower elastic will stretch instead...
- 1
-
One problem I am running into is my height- Once I have everything on, I have a gap between my chest and torso. Same on the back. If I push the chest down some, it does not fit as well in the chest .
You can see here, the shoulder bells do not fit very tight. I might need to do a warm water bath to make them a little wider to fit my shoulders.
The back piece does not fit directly on my back, you can see through the gap. Another piece I might need to do a warm water bend on the top of the back to flatten it out some.
- 1
-
Thanks to anyone who takes a look at my build thread. This is my first time armor build.
Name: Matt Certain
Height - 6 foot 2 inches tall
Weight - 220 lbs
Being a little bigger and taller this should be an interesting build.
I purchased my armor from ATA at the start of 2020 and have been working on it since.
I am a little late starting my thread, but better late than never.
Below is from the BBB day, I will post pictures of where I am now in the process.
- 2
TK96119 Requesting TK ANH Stunt EIB status [ATA] (1035)
in Request Expert Infantry Status
Posted
Thanks for the through and awesome response. I have some work to do over Christmas break! Good time to use up some PDO and get to work
Thanks again!