-
Posts
78 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Articles
Media Demo
Posts posted by Darth147
-
-
also started working on nico henderson helmet
here are some pics on how it compares to jims helmet
even though nicos helmet is bigger jims helmet has a bigger hole for your head
with nicos you have to do the side twist to put it on (nicos on the left jims on the right)
put some white primer on nicos (left)
- 1
-
3d printed the shins these are easier to join together than the fiberglass ones
-
added bondo to make the eye notch
need to do the outlines on the vents and probably repaint them since the black marker i used was too thick
i order a ultra fine point
side profile before i used the black marker on the details
ukswraths hovi mike speakers arrived
getting closer on the bucket
- 1
-
lost a lot of details on the abbs so i sanded them off and 3d printed some to glue on
still a lot of work to be done on the abb piece but i like the sharper look
just incase it doesnt work out i 3d printed a new abb barrel
- 1
-
in the beginning I cut the all the vents for air flow and thinking the helmets where like that in RO and plan on using a black mesh
well the vents looks pretty bad so I cut the whole thing out and just glued in the nico vents
this is the jimmi helmet
in the future i plan on printing the nico helmet
i actually sanded off the top of the abb greeblies details and cut the greeblie on meshmixer very thin an plan on just gluing it on top
havent been working on this project lately i got side swept with my other projects
too many prints not enough time to finish them all
-
finally glued in the vents
need to touch up the vents a bit
-
armor looks great
great job with what you have done
mine already has a few scratches most of them can be cleaned off and it gives it a natural battle worn look to it
even my abs anovos kit has those scratches from armor rubbing
-
did you scale up your abb armor
curious before i start printing it
-
I hate when the flies think landing on fresh paint is a good idea
good progress so far
-
i say chop the butt plate it will look a lot better
everything looks great so far
-
ived had the same issue going on with my scout trooper build
only way around it is sanding it off and doing light coats and make sure you give it enough time to cure before the other coats are added
-
@BigJasoni i wish i had just printed this armor
would of probably been done by now
fiber glass sucks to work with but it is what it is
i noticed the cod and the butt plates need reworking
- 1
-
a lot more ventilation and work now
besides the vent breaking on that spot
i need to sand it a bit more for it to go in better then fill in the sides with some jb weld and back it with some styrene like @11b30b4 suggested
- 4
-
thinking about replacing the main abb greeblie however im close to being done and dont want to mess it up my removing the original
i downloaded the stls that @BigJasoni has been working on to replace my abb armor and some other pieces in the future
much more detail with the 3d printed piece
- 1
-
havent done any work to the build yet been messing around with my printer(replacing the whole heating assembly ) major clog in the nozzle printed out some greeblies for the back vents on the helmet
it doesnt sit flush
not sure if i should sand them down or cut out all of the back vent and glue it on with some support from the inside
-
this is the last time on those pieces that i am going to cover them up.
at some point enough is enough
plus they kind of look like small grains of sand (battle damage/weathering) which im sure after a few troops it will get scratches and scuff marks
-
It really is
if I had a nickel for a pinhole
$$$$$$$$$- 1
-
found some pinholes and imperfections needing fixing
i got some resin on the abb buttons so they lost some sharpness hopefully i can recover from it
the legs need the most work with sanding
hope to sand down to 600 and give the pieces another coat
- 2
-
happy with the helmet
- 1
-
i was able to to apply some gloss white to the back ,barrel, thighs and helmet
was happy with how it turned out
i found some cracks on the barrel and the back
hopefully i can get away with filling them with spot putty
- 1
-
i get what you mean
the nico henderson helmet is good quality
ived had my printer down for a while
your build makes me want to level the bed and start printing again
keep up the good work
looking forward to seeing you build complete
youll probably be the first 3d print ROTK
-
ived seen this one too
not sure if its more accurate or not
-
good job so far
where did you get the armor files
ived been debating on printing some parts from my current ROTK armor
-
yeah when i wear the chest piece it covers everything even if i stretch my arms up
its the same length as my anovos abb piece.
measure twice cut once
Darth147s R1 BUILD-Part of the SCG Group Build
in Rogue One Build Threads
Posted
nicos has the parts in pieces just like the oxprops
jims hlemet is based of a the black series sculp
a bucket for everyone in the family