gmrhodes13

Leaps and bounds compared to the V1

Can't remember if I posted this link earlier, you may find it useful

My question is are the inside of the forearms supposed to look different or trimmed to the same “u” shape. I have them trimmed to where the flash was. Normally the right and left sides are a different shape/size, same as screen suits Also, the bottom cod piece of very bland and no hard lines to see where to exactly shape it too, I have a rough pencil marking for now but curious any tips or tricks. Trim line looks fine Bicep with the thumb print goes on the left arm NOTES ON BICEPS: In the original films, many of the biceps had an indentation, or "thumbprint" (normally worn only on the left) on the inside. As the biceps are interchangeable, this is not a requirement for any level. You can take off all the return edge on the shoulder bells if you wish too Swoop on the shoulder bells goes to the front Note: For ANH S/H and ESB as mentioned in the CRL for basic approval, shoulder bells are interchangeable. However, note that many (but not all of) the originals contained a "swoop" (slight curvature on one side) at the bottoms, which should ideally face the front. Some armor makers have incorporated this detail into their molds, but some have not and many times troopers get them backward. This is not a requirement at any level. <--- Front References to other WTF forearm builds Found from searching that the left forearms have a slight curve to it while the right is more straight Left Wrist Left Elbow Sorry if I've missed anything.

Nice work so far. Just watch out for print lines and cracks 3D printed components must have no visible print lines and must be smooth for a realistic appearance. You may also want to distress/weather your red cogs

If you use the "direct link" or link with the extension ie: .jpg, .png, .gif (or right click, copy and paste) your image will show in your post A good how too here

No issue for me, albeit I do like to give it a little heat so it's easier to bend. I use a heat gun, some use hot water bath or torch. Similar process to the belt I would think rough up the area inside and glue some scrap abs behind the crack, really depends were it is sitting on the thigh. Just make sure you try on some scraps, doesn't need much heat before the plastic is pliable

Lots of different ways to do it, check out some of the threads in this area https://www.whitearmor.net/forum/search/?q=lens&quick=1&type=forums_topic&nodes=4

Shim the sides (ab and kidney) per tutorial (is this required for initial approval?) Not normally but your GML can confirm, some are a little strict. You took a little too much material from the bottom corner of your thigh ammo strip, you could trim the end so it's as noticeable Agian entirely up to your GML Position of sniper knee plate On the sides the ridges should follow the inner ridge, with little gap under the front You could also add some foam behind the sniper plate to help hold it away from your thigh

You can get automotive paint in spray cans and that's what I normally use, albeit I do have spray equipment too as I used to spray cars Again it depends on what you are comfortable using, anything new you have to get used to using it and practice makes perfect, acrylic can go on a lot thicker than you would spray an enamel, but there is a fine line between enough paint and getting runs Having enough painting and drying space is essential. I also use metal hooks which are taped on with duct tape, easily comes apart. When it's too cold outside you have to improvise

You do have quite a lot of room between your shoulder bells and shoulder straps, perhaps tighter strapping. Your white elastic is being pulled quite a bit, doubling over the elastic can sometimes help to reduce this. Looks like you could also clean up the top of your vocoder as it's not well defined When taking your back photo don't tilt your head downwards as it shows a larger gap between your helmet and back Shoulder strap not central to backplate, adding elastic can help Gap between back plate and kidney, perhaps tighter strapping Try to have your armor pieces at the same heights Detonator should sit central to the belt, too much clip showing You have quite a large area on the side between your ab and kidney, you could add side shims to reduce this Sniper plate should not be angled backwards, hitting your thigh Swoop on shoulders normally faces forward, you have it facing backwards A good how to here for side shims You took a little too much material from the bottom corner of your thigh ammo strip, you could trim the end so it's as noticeable Swoop For ANH S/H and ESB as mentioned in the CRL for basic approval, shoulder bells are interchangeable. However, note that many (but not all of) the originals contained a "swoop" (slight curvature on one side) at the bottoms, which should ideally face the front. Some armor makers have incorporated this detail into their molds, but some have not and many times troopers get them backward. This is not a requirement at any level. <--- Front These are just suggestions and not required for base approval although your GML may require them. For Level 3, Drop boxes are vertically aligned with the end of the ammo belt with minimal gap between belt and box. For Level 3, the corners of the plastic ammo belt shall be trimmed at a 45 degree angle that meets the outer edge of the cloth belt. A few adjustments (and a belt) and you should be good Belt references. The top of the ABS belt shall sit at or just above the bottom of the central and vertical ab button panels. A slight overlap is suggested, but not required. Good luck

Welcome back, you may have noticed your build thread had been moved to "Build Threads Requireing Maintenance" this is because most of your images are missing and left with broken links, if you do have a copy it would be great if you could update your build thread A little difficult to see some details as your photos are of a low resolution but here are a few things you may want to address: Definitely looks like your thighs should come up as they are hitting your shins. Are your biceps snug or loose as they could be smaller? With cover strips they normally sit just inside the raised ridges (not all armor makes have the raised ridges), in your case you needed more room, this makes an issue as the raised areas are quite wide. In some cases people remove the raised areas and glue flat pieces, adding ABS paste and sanding/polish. If the gap between the raised ridges is not too big you can add larger cover strips, I would however speak with your GML (garrison membership liaison) as to how wide is acceptable for approval. This is an example of adding a shim after raised ridge has been removed Although these are for thighs but you can see what I mean with the raised areas, they have been removed in these threads You may need to trim your backplate so it sits above the kidney, one corner is stuck inside your kidney the other corner outside, but does look quite low. There are a few build threads which have made mods to the armor to better fit with height https://www.whitearmor.net/forum/topic/38416-crickets-rs-stunt-build-for-the-vertically-challenged/ https://www.whitearmor.net/forum/topic/38842-fragarocks-rs-stunt-build-not-to-scale/ https://www.whitearmor.net/forum/topic/42868-sha-shas-wtf-anh-stunt-build-complete/ For the posterior you may be able to add extra strapping more towards the front edges OR add some V tabs With a heat gun (or in oven) you bend strips of ABS plastic into the shape of a V, only glue one side and the other remains free to allow movement when you bend. Just helps stop the butt plate from pushing back from the back plate. A couple of adjustments you could make. Bring your belt up a little more at the front. The top of the ABS belt shall sit at or just above the bottom of the central and vertical ab button panels. A slight overlap is suggested, but not required. Looks like your gloves have folded over or it may be your sleeves, again hard to see. These are just suggestions and not required for base approval. For Level 3, Drop boxes are vertically aligned with the end of the ammo belt with minimal gap between belt and box. For Level 3, the corners of the plastic ammo belt shall be trimmed at a 45 degree angle that meets the outer edge of the cloth belt.

I stopped using Rust-oleum paint as it wasn't being consistent, no matter how much you shake the tin it would come out sandy at times without warning, make sure you shake as much as you can as well as between coats. I use acrylic automotive paints, doesn't matter if you paint gloss over gloss, dries quickly unlike enamel based paints and can be sanded and polished if needed. Everyone has their own way with painting or what paint they use so go with what ever you are more comfortable with.

I have had lots of issues with Rust-Oleum, mainly it not mixing properly and coming out in places like sand. With primer you are normally ok to give a light sand, personally I would use a 400 or 600 to give the next coat of paint something to grip too, 2000 is normally for final buff/polish. You really have to make sure the paint is fully dry before applying another coat, I've seen a lot of issues with crazing or splitting if not fully dry. Really depends how "smudged' it is but I would not think you would have to remove it all. Definitely try to shake as much as possible between application, even if it appears to be coming out consistently.

Looking forward to seeing your progress, good luck

Unless of course if you include Battlefront 2 references (I don't have the game so can't supply any other references), red variants showing SE style blaster, holster and rifle

Blink and you may have missed them, there were Stormtroopers in Mandalorian Season 3 Ep 7 I gather they must not have had enough IAC troopers for some scenes so they decided to throw in some Stormtroopers "who cares, nobody is going to notice right!" Must have had enough flight suits though as the TK's are wearing grey, did someone say new CRL Pretty easy to spot them here, appears to be 3 of them

I doubt it would be an option for the sidearm, as screen references show the pistol being used and a different holster, but yes no rifle unless you can find screen references. Really up to our DL and the LMO's to discuss whether it will be a new CRL or added as a variant, as you rightly point out many other detachments have multiple variants on single CRL's, such as IOC, Gunners etc, although Pathfinders have separate CRL's for their Shoretrooper variants so it could go either way. Taking a look at one of our own CRL's, TFA and there is additional language when using some optional weapons so that could be an option too, again up to the DL and LMO's OPTIONAL Level three certification (if applicable): Riot shield and riot baton must both be present. Pauldron, backpack, ammo pouches and ammo vest shall not be worn with riot baton/riot shield combination.

Side by side comparison of the holsters

My understanding was they only had 2 of the red variants and I've not seen any on screen of more than two at the same time

I guess you could try some eva foam

Great to get a dialogue to get the conversation started, albeit we do need a finished costume to be able to create a CRL or variant to a CRL. These troopers used the variant pistol, Mando ends up with at the end of S3E08 I would think the holster would be different too to accommodate the pistol, doesn't look as wide

Center looks much better. I'm guessing it's either because it's not glued or from the use of a thinner material but just noticed the curve on the end of the panels, compared with and earlier version which is straight

Great to hear, congratulations trooper and welcome to the FOTK ranks If you feel inclined to keep a record we have a trooping award program, more information here:

Only other thing I would suggest is use the right background, your GWL will thank you for it when it comes to editing your images (also if you want to apply for Expert Infantry as I edit those images )

That looks the biz, much closer.