-
Posts
19 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Articles
Media Demo
Posts posted by Patricktt
-
-
Patrick To
TK-8136
EIB
A4
Joseph
Thank you very much
-
2 minutes ago, giskard8 said:
Congratulations!
Thank you~Arthur
-
On 10/15/2018 at 6:49 AM, tk4949 said:
Congratulations
Thank you, Joseph
-
On 10/15/2018 at 6:29 AM, gmrhodes13 said:
Congratulations trooper
Thank you, bro
- 1
-
On 10/15/2018 at 5:54 AM, justjoseph63 said:
Hi Patrick, welcome and thank you for your TFA EIB application and your patience. Let's have a look, brother..
CRL and EIB Application Requirements:
All the required submission photos have been posted., your armour displays all necessary element as set out in the level 2 CRL, Congratulations on a job well done!.Other-Armor Fit/Assembly:
In this section we review observations made by your fellow troopers and ourselves. Some observations may lead to suggestions to improve the overall look of your armor. If any suggestions affects any application, it will be listed below.Overall an EXCELLENT build with this TFA armor, sir! Just a few notes for you...
1. Your spats should be lowered a bit to expose the small black rectangle at the bottoms. The one on your left is barely seen, and the one on the right cannot be seen at all. Just a small item, but these are the things that make the difference
Reference image
2. Tightening the strapping on your posterior armor would help eliminate of the gap you have between it and the belt and give you a better look.
Reference image
4. You have a double return edge on your wrist openings, which could use about 2 mm trimmed off and then cleaned up with some fine grit sandpaper for a cleaner look. (Easy fix)!! Be sure to leave a small amount of return edge, though!
Reference images
Centurion Suggestions:
In this section we prepare you the best we can for Centurion. If there are any areas of concern they will be discussed here.1. Your shoulder bells look a bit low, and should sit right at the level with the yoke. You have the required shoulder bell supports (tabs) but they are installed incorrectly. It looks as if you are using ABS for the tabs, and changing them out for metal ones may help with support issues. The tops could also be a bit closer to the yoke itself.
Reference image
2. Hopefully you will be aiming for level 3 next, and if so you will need to replace all the fabric gaskets with ones made from rubber.
Again, a simply awesome job on this armor, Patrick, and one you should certainly be proud to wear! Congratulations!
Thank you very much. I will fix them right now.
-
2 hours ago, justjoseph63 said:
Looking sharp, Patrick! Sorry for the delay, but we are working on this right now. Thanks for your patience!
Thank you Joseph ~please let me know if there are something I have missed
-
Light on F11D and repaint end cap
- 1
-
-
-
Name: Patrick To
Height: 5'7"
Weight: 180lbs
FISD Name: Patricktt
Legion ID#: 8136
Profile Page: http://www.501st.com/members/displaymemberdetails.php?userID=13314
Garrison: Hong Kong Garrison
Build Information
Armor Maker: Anovos
Helmet Maker: Anovos
Boots: Imperial Boots
Gloves: Imperial Boots
Electronics: TFA Helmet Fans - Echo's
Neck Seal: East Asia Supply
Gaskets: East Asia Supply
F11D Blaster: 3D print
SE-44C Blaster: 3D print
Helmet
Neck Seal
Gasket
Under Suit
Gloves
Boot
Armor
Belt
Holster(from R2Dan)
F11D
SE-44C
-
TK-8136 Requesting TFA EIB status (Anovos) (859)
in Request Expert Infantry Status
Posted
Thank you~bro